• 콘크리트학회논문집
• /
• 제26권1호
• /
• pp.79-86
• /
• 2014

이 연구는 표면매입 보강된 FRP 판과 콘크리트사이의 응력전달기구를 이론적으로 연구한 것으로서 이선형 부착모델을 이용하여 부착거동을 묘사하고 이를 실험 결과와 비교하여 신뢰성있는 해석방법을 제시하였다. 연구로부터, 표면매입된 FRP 판과 콘크리트사이의 계면특성을 고려한 미분방정식에 이선형 부착-미끄러짐 관계곡선을 사용하여 해석할 경우, 모델의 임계값인 최대전단강도와 미끄러짐 변위, 그리고 박락에 의한 연화거동이 시작될 때의 변위값 선정과정이 제시되었다. 또한 제안된 모델을 사용하여 부착길이가 다르게 보강된 표면매입 FRP 판의 미끄러짐 거동을 해석한 결과 실제 거동을 매우 근사하게 묘사할 수 있는 것으로 나타났다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 추계학술발표대회 논문집
• /
• pp.79-83
• /
• 2000

Interfacial and microfailure properties of carbon liber/bismaleimide (BMI) composites were evaluated using both tensile fragmentation and compressive Broutman tests with acoustic emission (AE). Since BMI is rather difficult matrix to apply for the conventional fragmentation test because of its too low elongation and too brittle and high modulus properties, dual matrix composite system was applied. After carbon fiber/BMI composite was prepared for rod shape by controlling differing curing stage, composites rod was embedded in toughened epoxy as outer matrix. The typical microfailure modes including fiber break, matrix cracking, and interlayer failure were observed during tensile testing, whereas the diagonal slippage in fiber ends was observed during compressive test. On the other hand, AE amplitudes of BMI matrix fracture were higher than carbon fiber tincture under tensile test because BMI matrix has very brittle and high modulus. The waveform of signals coming from BMI matrix fractures was consistent with AE amplitude result under tensile tests.

• Geomechanics and Engineering
• /
• 제13권5호
• /
• pp.881-892
• /
• 2017

Design and management of concrete slabs in concrete-faced rock-fill dams are crucial issues for stability and overall dam safety since cracks in the concrete face induced by stress, shrinkage, and deterioration can cause severe leakage from the reservoir into the dam. Especially, the increase of dam height to a certain level to enhance the storage capacity and to improve hydraulic stability can lead to undesirable deformation behavior and stress distribution in the existing dam body and in the concrete slabs. In such conditions, simulation of a concrete slab with a numerical method should involve the use of an interface element because the behavior of the concrete slab does not follow the behavior of the dam body when the dam body settles due to the increase of dam height. However, the interfacial properties between the dam body and the concrete slab have yet to be clearly defined. In this study, construction sequence of a 125 m high CFRD in South Korea is simulated with commercial FDM software. The proper interfacial properties of the concrete slab are estimated based on a comparison to monitored vertical displacement history obtained from the concrete slab. Possibility of shear strength failure under the critical condition is investigated based on the simplified model. Results present the significance of the interfacial properties of the concrete slab.

• The Journal of Advanced Prosthodontics
• /
• 제12권5호
• /
• pp.251-258
• /
• 2020

PURPOSE. The bond strengths between resin denture teeth with various compositions and denture base resins including conventional and CAD/CAM purposed materials were evaluated to find influence of each material. MATERIALS AND METHODS. Cylindrical rods (6.0 mm diameter × 8.0 mm length) prepared from pre-polymerized CAD/CAM denture base resin blocks (PMMA Block-pink; Huge Dental Material, Vipi Block-Pink; Vipi Industria) were bonded to the basal surface of resin teeth from three different companies (VITA MFT^®; VITA Zahnfabrik, Endura Posterio^®; SHOFU Dental, Duracross Physio^®; Nissin Dental Products Inc.) using resin cement (Super-Bond C&B; SUN MEDICAL). As a control group, rods from a conventional heat-polymerizing denture base resin (Vertex™ Rapid Simplified; Vertex-Dental B.V. Co.) were attached to the resin teeth using the conventional flasking and curing method. Furthermore, the effect of air abrasion was studied with the highly cross-linked resin teeth (VITA MFT^®) groups. The shear bond strengths were measured, and then the fractured surfaces were examined to analyze the mode of failure. RESULTS. The shear bond strengths of the conventional heat-polymerizing PMMA denture resin group and the CAD/CAM denture base resin groups were similar. Air abrasion to VITA MFT^® did not improve shear bond strengths. Interfacial failure was the dominant cause of failure for all specimens. CONCLUSION. Shear bond strengths of CAD/CAM denture base materials and resin denture teeth using resin cement are comparable to those of conventional methods.

• 콘크리트학회논문집
• /
• 제26권6호
• /
• pp.741-749
• /
• 2014

프리스트레스트 중공(PHC) 슬래브는 장경간에 적합하도록 경량화된 효율적인 프리캐스트 부재이며, 국내 외에서 많이 사용되고 있다. 특히, 국내에서는 현장타설콘크리트와 같이 사용되는 합성슬래브 형태로 주로 적용되고 있다. 그러나, 압출성형방식으로 제작되는 PHC 슬래브 부재는 매우 낮은 슬럼프의 콘크리트로 제작되어 타설 직후에도 표면경도가 높기 때문에 계면의 거친면 처리 및 전단연결재 배치가 어려운 단점이 있다. 이 연구에서는 PHC slab 부재와 토핑콘크리트 사이의 합성성능을 고찰하기 위하여 다양한 계면상태를 변수로 직접전단실험을 수행하였으며, 기존 실험결과를 수집하여 국내 외 수평전단강도 설계기준을 평가하였다.

• 한국세라믹학회지
• /
• 제30권7호
• /
• pp.549-556
• /
• 1993

Interfacial shear strength plays an important role in determining the mechanical properties of a fiber-reinforced ceramic composites. In this study, the effect ofinterlayer thickness on mechanical properties of Nicalon-fiber-reinforced SiC composites fabricated via polymer solution infiltration/chemical vapor infiltration (PSI/CVI) was studied. It was found that the flexural strength and fracture toughness of the composites were increased with the interlayer thickness and showed maximum value at the interlayer thickness of 0.66${\mu}{\textrm}{m}$. Typical flexural strength and fracture toughness of Nicalon-fiber-reinforced SiC composites with interlayer thickness of 0.66${\mu}{\textrm}{m}$ were 391.7$\pm$34.6MPa and 15.1$\pm$1.8MPa.m1/2, respectively.

• International Journal of Korean Welding Society
• /
• 제5권1호
• /
• pp.15-28
• /
• 2005

The ball shear test was investigated in terms of the effects of test parameters, i.e., shear height and shear speed, with an experimental and non-linear finite element analysis for evaluating the solder joint integrity of area array packages. Two representative Pb-free solder compositions were examined in this work: Sn-3.5Ag-0.75Cu and In-48Sn. The substrate was a common SMD type with solder bond pad openings of 460 $\mu$m in diameter. The microstructural investigations were carried out using SEM, and the IMCs were identified with EDS. Shear tests were conducted with the two varying test parameters. It could be observed that increasing shear height, at fixed shear speed, has the effect of decreasing shear force for both Sn-3.5Ag-0.75Cu and In-48Sn solder joints, while the shear force increased with increasing shear speed at fixed shear height. Too high shear height could cause some undesirable effects on the test results such as unexpected high standard deviation values or shear tip sliding from the solder ball. The low shear height conditions were favorable for screening the type of brittle interfacial fractures or the degraded layers in the interfaces. The shear speed conditions were discussed with the stress analyses of the solder ball, and we cannot find any conspicuous finding which is related to optimum shear speed from the stress analyses.

• 폴리머
• /
• 제24권3호
• /
• pp.326-332
• /
• 2000

유리섬유/불포화 폴리에스터 복합재료에서 섬유에 처리된 사이징제가 복합재료의 최종 물성에 미치는 영향을 상온에서의 접촉각 측정을 통해 고찰하였다. 본 연구에서는 폴리비닐알코올, 폴리에스터, 그리고 에폭시계 사이징제를 사용하여 유리섬유의 표면을 처리하였으며 각각의 물성을 비교하였다. 유리섬유의 접촉각은 증류수와 diiodomethane을 젖음액으로 사용하여 Washburn식을 기본으로 한 wicking법으로 측정하였다. 결과적으로 접촉각 측정에 의해 구한 표면자유에너지는 에폭시계 사이징제로 치리된 유리섬유에서 최대값을 나타내었다. 복합재료의 층간 전단 강도 (ILSS)와 파괴 인성 ( $K_{IC}$ )의 측정 결과로부터 사이징제의 처리에 따라 계면 결합력이 증진되며 결과적으로 복합재료의 기계적 강도가 증가함을 알 수 있었다. 이것은 복합재료에서 유리섬유의 표면 자유에너지 증가에 기인한다고 사료된다.

• 대한치과보철학회지
• /
• 제29권2호
• /
• pp.85-101
• /
• 1991

The purpose of this study was to determine the optimum range of laser energy density to the enamel surface of permanent incisors when they are irradiated with the pulsed Nd : YAG laser, Laser impacts on each experimental group were made at energy density of $20\sim50J/cm^2$ by 20 pulses of the pulse width 1.2 msec. The author investigated the enamel surface with the sunning electron microscope(SEM) and the surface roughness tester, and measured the shear bond strength between electrolytically etched Ni-Cr-Be alloy casting and composite resin. The obtained results were as follows: 1. The surface roughness of enamel after laser irradiation showed the significant difference level from the energy density $40J/cm^2(P<0.05)$. 2. The mean shear bond strength of etched-metal resin-bonded specimens were $154.23{\pm}33.30kg/cm^2$ at unlased enamel surface and $195.72{\pm}29.56kg/cm^2$ at lased energy density $30J/cm^2$, and showed a significant difference(P<0.05). 8. SEM photographs showed the irregular microcracks and the structural changes of lased enamel surface. 4. SEM photographs of the fracture surface after testing the shear bond strength showed the aspect of interfacial fracture between bonding agent and composite resin at the metal sides.

• 폴리머
• /
• 제36권5호
• /
• pp.612-616
• /
• 2012

본 연구는 표면처리에 따른 탄소나노튜브의 표면특성변화가 탄소섬유 강화 복합재료의 기계적 물성에 미치는 영향에 대하여 살펴보았다. 표면처리된 탄소나노튜브의 표면특성은 산-염기도 측정, FTIR, 그리고 XPS를 통하여 알아보았다. 복합재료의 기계적 계면특성은 층간전단강도(interlaminar shear strength; ILSS)와 임계응력세기인자(critical stress intensity factor; $K_{IC}$)를 통하여 고찰하였다. 실험결과 산-염기 상호반응에 의한 각각의 표면처리된 탄소나노튜브의 표면특성의 변화를 가져오며, 산처리한 MWNTs/탄소섬유/에폭시 복합재료의 경우 미처리 MWNTs, 염기 처리 MWNTs와 비교하여 우수한 기계적 물성을 보였다. 이는 산성을 가지는 MWNTs와 염기성의 에폭시 수지가 산-염기 및 수소결합에 의한 계면 결합력의 향상 때문이라 판단된다.