• Journal of Adhesion and Interface
• /
• v.10 no.2
• /
• pp.90-97
• /
• 2009

Dispersion and self-sensing evaluation for single-carbon fiber reinforced in three different acid-treated CNT-epoxy nanocomposites were investigated by electro-micromechanical techniques and wettability tests. Self-sensing based on contact resistivity exhibited more noise for single carbon fiber/acid-treated CNT-epoxy composites than it did for untreated CNT. However, the apparent modulus was higher the acid treated case than the untreated case which is attributed to better stress transfer. The interfacial shear strength (IFSS) between carbon fibers and the CNT-epoxy was lower than that between carbon fiber and neat epoxy due to the increased viscosity associated with the addition of the CNT. The CNT-epoxy nanocomposite exhibited more hydrophobicity than did neat epoxy. Change in the thermodynamic work of adhesion was consistent with changes in the IFSS but disproportional to that of the apparent modulus. The optimum condition of acid treatment on the need can be obtained instead of the maximum condition.

• Polymer(Korea)
• /
• v.27 no.4
• /
• pp.340-348
• /
• 2003

A previous stud-pull test was modified to measure the bond strength of polyurethane foam to carbon steel substrate. This test was appropriate in that the specimen foamed on Zn phosphated steel (0.95 kN) was broken at higher load than that of smooth galvanizing treated steel (0.38 kN). Among the samples foamed on the substrate atvarious preheating temperatures, the polyurethane foam to the steel held over 60$^{\circ}C$ exhibited very high bond strength. The samples were exposed at water vapor absorption, and, then, their bond strengths were measured. The adhesion was significantly reduced in the samples foamed on the steel at temperatures below 40$^{\circ}C$ and above 70$^{\circ}C$. For the polyurethane foams formulated with two blowing gases, the adhesion was higher by 0.03 kN in the samples with HCFC-l4lb than that with HFC-245fa. When the these samples were exposed at water vapor soaking, the reduction of the bond strength for the HFC-245fa blown sample was negligible due to smaller area fraction of void area filled with gas at interfacial area. Consequently, it was found that adhesion of polyurethane foam to metal substrate was determined by variation of microstructural features with substrate preheating, surface treatment type of blowing agent.

• Journal of the Korean Vacuum Society
• /
• v.10 no.2
• /
• pp.234-240
• /
• 2001

The diffusion barrier properties of TiN by using Cu(Mg) alloy film have been investigated. Cu(Mg) alloy film was deposited on air-exposed TiN film. Upon annealing, interfacial MgO of 100 $\AA$ has been formed due to the reaction of Mg with oxygen existed on the surface of TiN. Combined MgO/TiN structure prevented the interdiffusion of Cu and Si up to $800^{\circ}C$. To improve the adhesion of Cu(Mg) alloy film to the TiN, TiN layer was treated by $O_2$ plasma, followed by vacuum annealing at $300^{\circ}C$. It was found that increased oxygen on the surface of TiN film by plasma treatment enhanced segregation of Mg toward the interface, resulting in the formation of dense MgO layer. Improved adhesion characteristics have been formed through this treatment. However, increased power of $O_2$ plasma led to the formation of TiO$_2$ and decreased the Mg content to be segregated to the interface, resulting in the decrease in adhesion property. In addition, the deposition of 50 ${\AA}$ Si on the TiN enhanced the adhesion of Cu(Mg) alloy to TiN without deteriorating the TiN diffusion barrier characteristics.

• Journal of Adhesion and Interface
• /
• v.16 no.2
• /
• pp.69-75
• /
• 2015

Stone board for the rock bed was needed to reduce weight using thin thickness and reinforced materials. In this work, stone/wood board for rock bed was studied. Stone and wood were attached to reduce total weight of stone for rock bed. For reinforcing wood heat treatment method was used to change surface and mechanical properties. Mechanical strength of heat treated wood increased more than neat condition. The optimum heat treatment condition was set on $100^{\circ}C$ under tensile, flexural loads whereas surface energy was also obtained by contact angle measurement. Optimum adhesive condition was to get the maximum adhesion between stone and wood. Lap shear test was performed for stone/wood board with different adhesives such as amine type epoxy, polyurethane, chloro-rubber and vinyl chloride acetate type. Fracture surface of lap shear test was shown at wood fracture part on stone using amine type epoxy adhesive. It was found that for high adhesion between stone and wood the optimum adhesive was epoxy type for the rock bed.

• Journal of Adhesion and Interface
• /
• v.22 no.3
• /
• pp.98-105
• /
• 2021

In this study, we prepared a silver nanoparticle transferable adhesive composition with transparency and adhesive properties using UV-curable urethane acrylate containing silane groups. The urethane-based adhesive composition was applied between the Ag/PET film in which silver nanoparticles were patterned on PET and the PC film to be transferred. Immediately after UV-curing with UV, PET was removed to complete the manufacture of Ag/PC film. UV-curable urethane acrylate containing silane groups was synthesized using polycaprolactone diol (PCL), isophrone diisocyanate (IPDI), 2-hydroxyethyl methacrylate (HEMA), and (3-aminopropyl) triethoxysilane (APTES). The silane group of APTES can improve interfacial adhesion by reacting with the specially treated silver nanoparticle surface of the Ag/PET film. In addition, we improved the adhesion between silver nanoparticle and PC film by mixing UV-curable urethane acrylate containing a silane group and a functional acrylic diluent used as a diluent. We analyzed the synthesis process of urethane acrylate using FT-IR, and compared the adhesive properties, optical properties, and transfer properties according to the molar ratio of APTES and the acrylic diluent composition. As a result, the best transfer properties were confirmed in the adhesive composition prepared under the conditions of PUA2S1_0.5.

• Journal of the Korean Vacuum Society
• /
• v.8 no.2
• /
• pp.158-158
• /
• 1999

The post ion implantation has been applied to modify early-grown BN layer and improve the adhesion of the BN films. The effect of ion implantation doses on microstructure and interlayer was investigated by FTIR and HRTEM. And the hardness and delamination life time of N+-implanted BN films were measured. With increasing the ion dose up to 5.0×1015atoms/㎠, the change of IR spectrum is observed. At 5.0×1016atoms/㎠, a drastic transition of cubic phase into hexagonal phase is detected. The change of microstructure of early-grown layers by ion implantation is confirmed using HRTEM. Both microhardness and delamination life time of BN films increase with ion dose. The modification model of early-grown BN layers is briefly discussed based on the displacement per atom and excess boron in the BN film induced by ion irradiation.

• Polymer(Korea)
• /
• v.26 no.3
• /
• pp.326-334
• /
• 2002

The purpose of this work was the producing of a biodegradable poly($\varepsilon$-caprolactone) (PCL) microcapsule and the analyzing of form and features for the manufacturing conditions which could be observed in a prospective drug delivery systems (DDS) through drug release. The effects of different stirring rates, stirring times and concentrations of emulsifier for the diameter and form of the microcapsules were observed using image analyzer (IA) and scanning electron microscopy (SEM). As a result, the microcapsules were made in wrinkle and spherical forms with a mean particle size of 40~300$\pm$20 $mu extrm{m}$. PCL microcapsules containing drugs were confirmed using FT-IR spectra. The role of interfacial adhesion between PCL and drug was determined by contact angle measurements. The drug release test of PCL microcapsules was characterized by UV/vis. spectra. It was found that the drug release rate of the microcapsules prepared with high concentration emulsifier was significantly fast.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.90-98
• /
• 2004

Nano/micro-scale studies on friction properties were conducted on Si (100) and three self-assembled monolayers (SAMs) (PFOTC, DMDM, DPDM) coated on Si-wafer by chemical vapor deposition technique. Experiments were conducted at ambient temperature $(24{\pm}1^{\circ}C)$ and humidity $(45{\pm}5\%)$. Nano-friction was evaluated using Atomic Force Microscopy (AFM) in the range of 0-40nN normal loads. In both Si-wafer and SAMs, friction increased linearly as a function of applied normal load. Results showed that friction was affected by the inherent adhesion in Si-wafer, and in the case of SAMs the physical/chemical structures had a major influence. Coefficient of friction of these test samples was also evaluated at the micro-scale using a micro-tribotester. It was observed that SAMs had superior frictional property due to their low interfacial energies. In order to study of the effect of contact area on friction coefficient at the micro-scale, friction was measured for Si-wafer and DPDM against Soda Lime balls (Duke Scientific Corporation) of different radii 0.25 mm, 0.5 mm and 1 mm at different applied normal loads $(1500,\;3000\;and\;4800{\mu}N)$. Results showed that Si-wafer had higher friction coefficient than DPDM. Furthermore, unlike that in the case of DPDM, friction was severely influenced by wear in the case of Si-wafer. SEM evidences showed that solid-solid adhesion to be the wear mechanism in Si-wafer.

• Composites Research
• /
• v.27 no.3
• /
• pp.109-114
• /
• 2014

Manufacture of nancomposites has simple process for developing nanocomposites due to the increasing applications using nanofillers. This work studied nanofiller coated glass fiber for reinforcing material with good wetting and conductivity and the morphology of nanofiller coated glass fiber was analyzed by FE-SEM. The durability of reinforced glass fiber was investigated with different shapes of nanofillers using sonication rinsing method. Fatigue test was performed to evaluate the adhesion of reinforcing interface and stability of nanofiller coating layer for single fiber reinforced composites. Apparent modulus and conductivity of nanofiller coating layer were evaluated to realize multifunctional of nanocomposites. Fiber type of nanofiller was better than plate type due to better cohesion between fiber and nanofillers. At last, the stability of fiber type nanofiller of coating layer has better durability and conductivity than plate type case.

• Journal of Adhesion and Interface
• /
• v.14 no.1
• /
• pp.36-42
• /
• 2013

To improve hydrolytic stability of polyurethane (PU) adhesives, a silane coupling agent (SCA) was added. 3-Isocyanatopropyl triethoxy silane (ITS) as a SCA has two functional groups in the main chain and it is used to improve an interfacial interaction between polymer and inorganic material or metal. In this study, PU adhesives with different amounts of ITS from 0 to 1 wt% were synthesized. Pot time, modulus, thermal stablilty, and adhesive force of the obtained samples were measured. The results showed that the adhesives with ITS showed better properties than that of pure one.