• 한국유체기계학회 논문집
• /
• 제13권2호
• /
• pp.5-11
• /
• 2010

The nanofluidics is characterized by a large surface-to-volume ratio, so that the surface properties strongly affect the flow resistance. We present here the results showing that the effect of wetting properties and the surface roughness may considerably reduce the friction of fluid past the boundaries. For a simple fluid flowing over hydrophilic and hydrophobic surfaces, the influences of surface roughness are investigated by the nonequilibrium molecular dynamics (NEMD) simulations. The fluid slip at near a solid surface highly depends on the wall-fluid interaction. For hydrophobic surfaces, apparent fluid slips are observed on smooth and rough surfaces. The solid wall is modeled as a rough atomic sinusoidal wall. The effects on the boundary condition of the roughness characteristics are given by the period and amplitude of the sinusoidal wall. It was found that the slip velocity for wetting conditions at interface decreases with increasing effects of surface roughness. The results show the surface rougheness and wettability determines the slip or no-slip boundary conditions. The surface roughness geometry shows significant effects on the boundary conditions at the interface.

• 대한화학회지
• /
• 제8권2호
• /
• pp.57-61
• /
• 1964

It was verified at Part Ⅰ of this investigation that there is a minimum wettability between molten iron and graphite, which was preliminarily coated with magnesium, and thus the spheroidization of graphite might have resulted from the lack of wettability between magnesium-adsorbed graphite and iron matrix. Being continued from the last work, the wettability between pure iron and graphite, coated with the various thickness of cerium, are measured at melting point of pure iron in vacuum and 200 mmHg argon gas atmosphere. The result indicates the presence of a minimum wettability at a critical thickness of cerium film as was proved in the case of magnesium. The experimental analysis shows that, the minimum wettability could be attributed entirely to a minimum work of adhesion between liquid iron and graphite at a critical concentration of cerium in the iron-graphite interface.

• Journal of Welding and Joining
• /
• 제7권3호
• /
• pp.36-43
• /
• 1989

The furnace brazing in a Ar of copper to martensitic stainless steel(13.5Cr) using Cu-(5~8%)P-(0~8%)Sn powders was investigated. Shear strength, wettability, reacted layer, defect ratio at the stainless steel interface was evaluated. As Sn was added to the Cu-P powders, defect ratio and P content at the stainless steel interface decreased. And also as Sn was added, defect form at the stainless steel interface changed from the continuous layer to the discrete type, and shear strength of the brazed joint increased.

• Journal of Welding and Joining
• /
• 제25권6호
• /
• pp.78-83
• /
• 2007

The wettability of Sn-Xwt%Cu(X=$0{\sim}3wt%$) solder was evaluated with wetting balance tester. And, the intermetallic compounds(IMCs) which were formed at the interface between solders and pads were investigated by using scanning electron microscopy(SEM) and energy dispersive spectroscopy(EDS). The wetting force of Sn-0.7wt%Cu solder was higher than that of 100wt%Sn and Sn-3.0wt%Cu solder. The value of $\gamma_{fl}$ and ($\gamma_{fs}-\gamma_{ls}$) had a tendency to increase with increasing the wetting temperature. The activation energy with bare Cu pad and flux with 15% solid content was increased in the following order: Sn-0.7Cu (68.42 kJ/mol) ; Sn-3.0Cu(72.66 kJ/mol) ; Sn solder(94.53 kJ/mol). It was identified that the Cu6Sn5 phase was formed at the interface between Sn-Xwt%Cu solder and Cu pad.

• Tribology and Lubricants
• /
• 제35권2호
• /
• pp.94-98
• /
• 2019

The riblet structure like shark skin has been widely studied owing to its drag reduction and anti-fouling properties. In this study we simulated the wettability of an oil droplet on a riblet surface. We developed a numerical analysis method using the Wenzel equation and Cassie-Baxter equation that can estimate the contact angle with a penetrated depth of the droplet on rough surfaces. Riblet surfaces with nine scales composed of five hemi-elliptical ribs are generated numerically. The variation of contact angles with fractional depth of penetration for the generated riblet surfaces with and without coatings is demonstrated in the condition of solid-air-oil and solid-water-oil interfaces. The contact angle for the uncoated surface decreases with increasing fractional depth of penetration more drastically than that for the coated surface. For the effect of surface roughness on the contact angle of the droplet, the oleophilic surface gives lower contact angle when the surface is rougher, whereas the oleoophobic surface gives higher contact angle with higher roughness To verify the analysis results, the wetting angle was measured in the solid-air-oil interface and solid-water-oil interface for the shark-skin template and shark-skin replica. The effects of teflon coating were also evaluated. It is shown that the simulation results cover the experimental ones.

• 한국주조공학회지
• /
• 제12권2호
• /
• pp.149-154
• /
• 1992

The wetting behaviour of SiC/Al-Li composite interface has been investigated by using an infiltration method. The critical pressure for melt infiltration into SiC particulate preform has been determined by measuring the melt infiltration distance changes with the variation of applied pressure. The threshold pressure of pure Al, Al-0.2wt%Li, Al-0.5wt%Li for melt infiltration are 3.94, 3.93, $3.7Kg/cm^2$ respectively, which implies a slight improvement in wettability of SiC/Al composite by addition of Li. The threshold pressure for melt infiltration also changes with the variation of other parameters such SiC particulate size, SiC particulate fraction and melt temperature.

• 한국염색가공학회지
• /
• 제13권1호
• /
• pp.18-22
• /
• 2001

Effects of cationic surfactants old the wetting behavior of the DMDHEU treated cotton fibers were investigated using a technique based on the Wilhelmy principle. The results indicated that Interactions between the fiber and water ill the interface make contributions to wettability of the cotton fiber surface because of reorientation of polar groups at the interface. The effects of types and concentration of cationic surfactant on the wettability of both control and durable press(DP) finished cotton fiber are discussed. Below and near the critical micelle concentration(cmc), the adsorption of hexadecyltrimethylammoniumbromide(HTAB) on the control fiber makes the fiber surface more hydrophobic. Near and above the cmc of octadecyltrimethylammouniumbromide(OTAB) , the decrease in advancing contact angles indicates that the control cotton surface became hydrophilic. By the adsorption of both HTAB and OTAB onto the fiber surface, the hydrophobicity of the DP finished fiber surface became mere hydrophilic.

• 접착 및 계면
• /
• 제3권2호
• /
• pp.17-29
• /
• 2002

Micromechanical 시험법과 표면 젖음성 측정을 이용한 implant용 생분해성 복합재료의 계면물성과 미세파괴 분해 메카니즘을 연구하였다. 분해시간이 경과함에 따라서 poly(ester-amide) (PEA)와 생활성 유리섬유의 인장강도와 탄성률 그리고 신율은 점차적으로 감소하는 경향을 보인 반면, chitosan 섬유는 거의 변화가 없었다. 생활성 유리섬유와 poly-L-lactide(PLLA) 사이의 계면전단강도는 PEA나 chitosan 섬유 시스템의 경우보다 더 큰 값을 보였으나, 계면전단강도 감소 속도는 가장 빨랐고 chitosan 섬유의 경우가 가장 느린 결과를 보였다. 접착일 ($W_a$)은 생활성 유리섬유와 PLLA 사이에서 가장 높은 값을 나타냈으며, 이러한 표면 젖음성 결과는 계면전단강도 결과와 잘 일치하였다. 계면물성과 미세파괴 분해 메카니즘은 생분해성 복합재료의 성능을 조절할 수 있는 가장 중요한 요인들이다.

• International Journal of Fluid Machinery and Systems
• /
• 제3권4호
• /
• pp.386-395
• /
• 2010

The article is focused in three areas. In the first part there are analyzed the adhesion forces at the liquid and solid surface interface. There are shown the measured values of surface energy for different types of surfaces. The value of surface energy is decisive for determining the extent of the surface wettability by the liquid. The second part points to the possible negative effects of partly wettable surfaces, showing susceptibility to cavitation. The third section describes the practical aspects of surface wettability by the liquid. Under the new boundary conditions bases, expressing the effect of adhesion forces, there are determined the centrifugal pump characteristics.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제52권5호
• /
• pp.206-206
• /
• 2003

It is hard to expect excellent electrical, mechanical and chemical properties from most of the composite materials presently used as insulators due to insufficient wettability property caused by the difference of interfacial properties between the matrix material and the reinforcer. Therefore, various interfacial coupling agents have been developed to improve the interfacial properties of composite materials. But if the wettable coupling agents are used outdoor for a long time, change in quality takes place in the coupling agents themselves, bringing about deterioration of the properties of the composite materials. In this study, glass surface was treated by plasma to examine the effect of dry interface treatment without coupling agent. It was identified that the optimum parameters for the best wettability of the samples at the time of generation of plasma were oxygen atmosphere, 0.1 torr of system pressure, 100 W of discharge power, and 3 minutes of discharge time. Also, the surface resistance rate and dielectric property were improved.