• 비파괴검사학회지
• /
• 제28권6호
• /
• pp.504-511
• /
• 2008

This paper proposes an ultrasonic measurement method for measurement of linear interfacial stiffness of contacting surface between two steel plates subjected to nominal compression pressures. Interfacial stiffness was evaluated by using shear waves reflected at contact interface of two identical solid plates. Three consecutive reflection waves from solid-solid surface are captured by pulse-echo method to evaluate the state of contact interface. A non-dimensional parameter defined as the ratio of their peak-to-peak amplitudes are formulated and used to calculate the quantitative stiffness of interface. Mathematical model for 1-D wave propagation across interfaces is developed to formulate the reflection and transmission waves across the interface and to determine the interfacial stiffness. Two identical plates are fabricated and assembled to form contacting surface and to measure interfacial stiffness at different states of contact pressure by means of bolt fastening. It is found from experiment that the amplitude of interfacial stiffness is dependent on the pressure and successfully determined by employing pulse-echo ultrasonic method without measuring through-transmission waves.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.528-533
• /
• 2002

The mechanical and metallurgical properties of friction welded joints type 5052 Al alloy/A36 steel have been studied in this paper. The joint strength increased with increasing upset pressure and friction time till it reached the critical value. The joint strength was fixed at low strength compare to that of base metal in the case of increasing friction time. Microstructure of 5052 Al alloy was greatly deformed near the weld interface. The very fine and equaxied grain structure was observed at the near interface. The elongated grain was formed outside dynamic recrystallizatoin region at the peripheral part, while the A36 steel' side was not deformed. The hardness of the near interface was slightly softer than that of 5052 Al alloy base metal. The maximum softening width was about 8mm from the interface. In the present work, the friction welding condition, t$_1$=0.5sec, P$_2$=137.5MPa, showed a maximum joint strength (202MPa) when friction pressure, upset time and rotation speed were fixed at 75MPa, 5sec, 2000rev/min and these were the optimum friction welding condition of 5052Al/A36 steel joints.

• 한국전산유체공학회지
• /
• 제17권3호
• /
• pp.99-107
• /
• 2012

In this paper, the shock waves in compressible solids and liquids are simulated using a six-equation diffuse interface multiphase flow model that is extended to the Cochran and Chan equation of state. A pressure relaxation method based on a volume fraction function and a pressure-correction equation are newly implemented to the six-equation model. The developed code has been validated by a shock tube problem with liquid nitromethane and an impact problem of a copper plate on a solid explosive. In addition, a new problem, an impact of a copper plate on liquid nitromethane, has been solved. The present code well shows the wave structures in compressible solids and liquids without any numerical oscillations and overshoots. After the impact of a solid copper plate on liquid, two shock waves (one propagates into liquid and the other into solid) are generated and a material interface moves to the impacting direction. The computational results show that the shock velocity inside the liquid linearly increases with the impact velocity.

• 한국생산제조학회지
• /
• 제19권6호
• /
• pp.841-846
• /
• 2010

The present study examined the mechanical properties of the friction welding with hollow and solid shaft of SM45, of which the diameter is 25.2mm and 33mm. Friction welding was conducted at welding conditions of 2,000rpm, friction pressure of 50MPa, upset pressure of 70MPa, friction time of 0.4sec to 1.4sec by increasing 0.2sec, upset time of 2.0 sec including variable such as friction time are following. Under these conditions, a tensile test, a hardness test and a microstructure of weld interface were studied. The results were as follows : When the friction time was 1.0 seconds under the conditions, the maximum tensile strength of the friction weld happened to be 1,094MPa, which is 120% compared with the tensile strength of SM45C base metal. The upset length linearly increased as friction time increased. According to the hardness test, the hardness distribution of the weld interface was formed from 475Hv to 739Hv. HAZ(Heat Affected Zone) was formed from the weld interface to 2mm of SM45C.

• 항공우주시스템공학회지
• /
• 제12권2호
• /
• pp.15-22
• /
• 2018

7개의 방정식으로 구성된 DIM을 사용하여 압축성 다상 유동에 대해 연구하였다. 액체와 기체의 상세한 경계면 유동 구조를 얻기 위해 5 차의 MLP와 변형된 HLLC 근사 리만 해법을 포함하는 고차 수치기법이 구현되었다. 수치 방법의 유효성 검증을 위해 물과 공기로 구성된 다양한 1차원 충격관 문제를 해석하였고, 불연속면에 대해 뛰어난 해상도를 얻을 수 있었다. 마하수 1.22의 충격파 조건에서의 2차원 공기-헬륨 기포에 대한 충격파 상호 작용을 수치 해석하였고, 충격파 현상들을 잘 모사하였으며 실험결과와 비교 검증하였다.

• 한국세라믹학회지
• /
• 제26권5호
• /
• pp.617-624
• /
• 1989

Piezoelectric composites of O-3 connectivity were prepared by thermosetting barium titanate-phenolic resin composite under various cruing pressure. Among three kinds of pore in O-3 type ceramic-polymer composite, such as matrix pores, particle pores, and ceramic-polymer interface pores, the effect of interface porosity on the dielectric and piezoelectric constant was investigated. In pure barium titanate ceramics, the porosity factor of dielectric and piezoelectric constants were 5.7 and 5.0, respectively. However, in BaTiO3-polymer composite, the interface porosity factor of the piezoelectric constant was greater than that of the dielectric constant, interface porosity factor b in d33 was 9.8 and in r 4.6. On the other, piezoelectric voltage constant g33 was independent of the porosity of barium titanate ceramics. But in composite system, the piezoelectric voltage constant g33 was decreased with interface porosity.

• 한국지반공학회논문집
• /
• 제38권9호
• /
• pp.45-52
• /
• 2022

암반내 불연속면이나 지반-구조물의 접촉면은 열-수리-역학적으로 연계된 거동 특성을 보이므로, 온전한 지배방정식에 근거한 경계면 요소의 개발이 필요하다. 본 논문은 경계면 요소에 대한 힘평형 방정식, 유체의 연속방정식 그리고 에너지 평형 방정식을 유도하였다. 그리고 경계면 요소에 대한 탄소성 역학 모델의 강성행렬을 제시하였다. 개발된 유한요소는 2차원 조건에서 변위는 6절점, 수압과 온도는 4절점을 사용한다. 단층내 유체 주입에 대한 완전연계된 THM 해석은 단층내의 유효응력 감소와 주위 암반의 온도 수축에 의한 주입압의 복합적인 변화을 모델링 할수 있었다. 하지만, 열적 현상을 무시한 HM해석은 수리-역학적 변수를 과다하게 산정하였다.

• Structural Engineering and Mechanics
• /
• 제15권3호
• /
• pp.315-329
• /
• 2003

As shear occurs along a soil-structure interface, a localized zone with a thickness of several grain diameters will develop in soil along the interface, forming an interfacial layer. In this paper, the behaviour of a soil-structure interface is studied numerically by modelling the plane shear of a granular layer bounded by rigid plates. The mechanical behaviour of the granular material is described with a micro-polar hypoplastic continuum model. Numerical results are presented to show the development of shear localization along the interface for shearing under conditions of constant normal pressure and constant volume, respectively. Evolution of the resistance on the surface of the bounding plate is considered with respect to the influences of grain rotation.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.589-592
• /
• 2008

For the system of a droplet on an insulator-coated electrode, the Lippmann-Young equation is derived by considering the deformation of interface near the three-phase contact line. The equation governing the deformation of interface, which describes the local balance of the Maxwell stress and the capillary pressure, is integrated along the interface. The integration leads to the Lippmann-Young equation which is shown to represent the macroscopic balance of horizontal force acting on entire meniscus. Young's angle is assumed to be not affected by the Maxwell stress. The meaning and validity of the assumption are discussed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.442-447
• /
• 2008

This paper presents a new approach to simulate fluid-solid interaction problems involving non-matching interfaces. The coupling between fluid and solid domains with dissimilar finite element meshes consisting of 4-node quadrilateral elements is achieved by using the interface element method (IEM). Conditions of compatibility between fluid and solid meshes are satisfied exactly by introducing the interface elements defined on interfacing regions. Importantly, a consistent transfer of loads through matching interface element meshes guarantees the present method to be an efficient approach of the solution strategy to fluid-solid interaction problems. An arbitrary Lagrangian-Eulerian (ALE) description is adopted for the fluid domain, while for the solid domain an updated Lagrangian formulation is considered to accommodate finite deformations of an elastic structure. The stabilized equal order velocity-pressure elements for incompressible flows are used in the motion of fluids. Fully coupled equations are solved simultaneously in a single computational domain. Numerical results are presented for fluid-solid interaction problems involving nonmatching interfaces to demonstrate the effectiveness of the methodology.