• Geomechanics and Engineering
• /
• 제12권3호
• /
• pp.399-415
• /
• 2017

A series of direct shear tests were conducted to investigate the frictional properties of the interface between structures and the filling soil of Chongqing airport fourth stage expansion project. Two types of structures are investigated, one is low carbon steel and the other is the bedrock sampled from the site. The influence of soil water content, surface roughness and material types of structure were analyzed. The tests show that the interface friction and shear displacement curve has no softening stage and the curve shape is close to the Clough-Duncan hyperbola, while the soil is mainly shear contraction during testing. The interface frictional resistance and normal stress curve meets the Mohr-Coulomb criterion and the derived friction angle and frictional resistance of interface increase as surface roughness increases but is always lower than the internal friction angle and shear strength of soil respectively. When surface roughness is much larger than soil grain size, soil-structure interface is nearly shear surface in soil. In addition to the geometry of structural surface, the material types of structure also affects the performance of soil-structure interface. The wet interface frictional resistance will become lower than the natural one under specific conditions.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.319-320
• /
• 2002

Numerical simulation of chip formation during high speed machining requires knowing the friction at tool/chip interface. This parameter is hardly identified and generally the loadings (temperature, force) during the identification are not similar to those encountered during machining. Thus, Coulomb friction identified with pin-on-disc device is often used to conduct numerical simulation. The used of this technique cannot leads to good numerical results of chip formation compared to the experimental tests especially in the case of low uncut chip thickness. In this contribution, we propose a new method to evaluate the friction at tool/chip interface. In fact several Coulomb friction parameters are identified corresponding to several parts of the cutting tool. Experimental tests have been conducted allowed us to determinate both the level and the distribution of the Coulomb friction. Experimental results are also compared to the results of orthogonal cutting simulation. We show that this technique allows predicting accuracy results of chip formation.

• 한국지반공학회논문집
• /
• 제17권6호
• /
• pp.207-213
• /
• 2001

조밀한 건조조립토와 건설재료(콘크리트재)사이의 경계에서의 동마찰계수를 구하기 위하여 진동대를 사용하여 동적직접전단시험을 실시하였다. 조밀한 건조조립토와 건설재료사이의 동마찰계수는 본 연구에서 고려한 미끄러짐 속도의 범위안에서는 크게 변하지 않음을 알 수 있었다. 그리고 동마찰계수는 조립토의 평균입경이 증가함에 따라 감소하였고, 이에 대한 관계식을 제안하였다. 또한 이 계수를 같은 조립토에 대하여 실시한 평면변형률시험으로 얻어진 내부마찰각으로부터의 마찰계수와 비교하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.621-628
• /
• 2003

To prevent the percolation of leachate through the bottom of waste landfills, the liner system of various layers, such as compacted clay, geomembrane, geonet, geotextiles, and geocomposite is designed. Since the friction angle between a geomembrane and other geosynthetics is usually lower than that of the soil alone, the interfaces between soil and geosynthetic or geosynthetic-geosynthetic may become a possible plane of weakness, which leads to potential instability of the system under load of waste at side slopes. In this study, large triaxial tests are carried out with samples of remoulded wastes and direct shear interface friction tests are carried out to understand the frictional properties of geosynthetic-geosynthetic interfaces, which are required for analyzing the safety of side-slope liner systems.

• Tribology and Lubricants
• /
• 제29권6호
• /
• pp.372-377
• /
• 2013

This study investigated the interface temperatures for the sliding friction of three types of pins fabricated with thermocouple wires by the suction casting method. Optical microscopy was used to examine the surrounding material state at the bonding interface with the thermocouple wires. Friction tests were performed under dry sliding conditions against stainless steel 304 at nominal stresses of 1.42-4.25 MPa and sliding speeds of 0.5-1.25 m/s. Tribological data were collected using a custom-made pin-on-disk apparatus that measured the interface temperature and corresponding friction coefficient. Static tests were performed to demonstrate the functionality and reliability of the thermocouple wires-combined temperature sensor (TCTS). Each TCTS showed good linearity and sensitivity and very similar response times for the thermocouple and critical temperature during sliding friction.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.813-818
• /
• 2009

Shear properties of plastic bottle film/plastic bottle film and plastic bottle film/granitic soil which were evaluated from static friction tests. The monotonic shear experiments were performed by using an tilt table apparatus and large direct shear device. The test results showed that the friction angle of each interface and the interface depended on the amount of normal stress, the type of the interface used. Therefore, the testing method should be determined carefully by considering the type of loads and normal stress expected in the field with using the materials installed in the site.

• 한국지반환경공학회 논문집
• /
• 제13권8호
• /
• pp.65-73
• /
• 2012

우리나라 화강암 분포지역에서 주로 발견되는 토사-암 경계면은 토사 자체의 전단강도보다 더 작은 값을 갖기 때문에 강우 시 비탈면 붕괴의 중요한 요인 중 하나로 알려져 있다. 그러나 토사-암 경계면이 비탈면의 안정성에 미치는 영향에 대한 연구가 부족한 실정이다. 따라서 본 연구에서는 토사-암 경계면이 비탈면 안정성에 미치는 영향을 파악하기 위한 기초 연구로써 서로 다른 입도를 갖는 세 종류의 모래와 이를 이용한 인공 암석을 제작하여 모래, 모래-인공암석 경계면에서의 전단강도를 얻기 위한 직접전단시험을 실시하였다. 직접전단시험 결과, 경계면 마찰각은 입도와 표면 거칠기에 따라 변화하며, 경계면 마찰각비 ${\mu}(={\delta}/{\Phi})$는 약 0.75 ~ 0.96의 범위를 갖으며, 이러한 시험 결과들은 모래 자체보다 모래-인공암석 경계면의 마찰각이 더 작은 값을 갖는다는 것을 나타낸다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.356-363
• /
• 2004

In this research, the shear behavior of four different interfaces consisting of 4 types of geosynthetics was examined, and both static and dynamic tests for the geosynthetic interface were conducted. The monotonic shear experiments were performed by using an inclined board apparatus and large direct shear device. The interface shear strength obtained from the inclined board tests were compared with those calculated from large direct shear tests. The comparison results indicated that direct shear tests are likely to overestimate the shear strength in low normal stress range where direct shear tests were not performed. Curved failure envelopes were also obtained for interface cases where two static shear tests were conducted. By comparing the friction angles measured from three tests, i.e. direct shear, inclined board, and shaking table tests, it was found that the friction angle might be different depending on the test method and normal stresses applied in this research. Therefore, it was concluded that the testing method should be determined carefully by considering the type of loads and the normal stress expected in the field.

• 한국지반환경공학회 논문집
• /
• 제8권1호
• /
• pp.49-55
• /
• 2007

폐타이어의 트레드를 지반보강재로서 활용하기 위해서는 타이어 외면 및 내면과 흙간의 내부마찰각 그리고 폐타이어 연결부의 강도특성을 알아야 한다. 본 연구에서는 폐타이어 트레드와 모래 및 풍화토간의 접촉면마찰각을 알기 위해 흙의 다짐정도를 달리하여 대형직접전단시험을 수행하였다. 직접전단시험 결과 모래-타이어 외면간의 마찰각비(${\delta}/{\phi}$)는 1.06배 이상, 모래-트레드 내면간의 ${\delta}/{\phi}$는 0.93배 이상, 풍화토의 마찰각비(${\delta}/{\phi}$)는 트레드 외면과 내면에 대하여 각각 0.98, 0.92로 나타났다. 또한 UTM을 이용하여 폐타이어 연결부의 재료에 따른 인장강도시험을 수행하였다. 시험 결과 고장력 볼트를 사용한 인장시험에서 볼트의 개수 및 와셔의 크기가 증가할수록 연결부에서의 인장강도는 증가하였으며 폴리프로필렌 로프 연결의 경우가 볼트연결의 경우보다 작은 강도를 나타내었다.

• Steel and Composite Structures
• /
• 제5권4호
• /
• pp.259-269
• /
• 2005

Many slab-on-girder bridges around the world are being assessed because they are approaching the end of their anticipated design lives or codes are permitting higher allowable loads. Current analytical techniques assume that the concrete and steel components act independently, typically requiring full-scale load testing to more accurately predict the remaining strength or endurance of the structure. However, many of the load tests carried out on these types of bridges would be unnecessary if the degree of interaction resulting from friction at the steel-concrete interface could be adequately modeled. Experimental testing confirmed that interface friction has a negligible effect on the flexural capacity of a slab-on-girder beam however, it also showed that interface friction is significant under serviceability loading. This has led to the development of an improved analytical technique which is presented in this paper and referred to as the slab-on-girder mixed analysis service load assessment approach.