• Journal of the Korean GEO-environmental Society
• /
• v.20 no.10
• /
• pp.39-46
• /
• 2019

The interaction between the ground and structures should be considered for seismic design of group piles supporting the superstructure. The p-y curve has been used widely for the analysis of nonlinear relationship between the ground and structures, and various researches have conducted to apply the dynamic p-y curve for seismic design of group piles. This curve considers the interaction between the ground and structures under the dynamic load such as an earthquake. However the supported effect by the pile cap and the interaction by inertia behavior of superstructures. Therefore, the shaking table test was conducted to verify the effect of the change of the pile cap in group piles supporting superstructures embedded in sandy soil. The test condition is that the arrangement and distance between centers of piles are fixed and the length of the pile cap is changed for various distances between the pile cap side and the pile center. The result shows that the distance between the pile cap side and the pile center have an effect on the dynamic p-y curve and the effect of group piles.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.2
• /
• pp.355-365
• /
• 2014

Concrete-filled tubes (CFTs) have been used in civil engineering practices as a column of buildings and a bridge pier. CFTs have several advantages over the conventional reinforced concrete columns, such as rapid construction, enhanced buckling resistance, and inherited confinement effect. However, CFT component have not been widely used in civil engineering practice, since the design provisions among codes significantly vary each other. It leads to conservative design of CFT component. In this study, the design provisions of AISC and EC4 for CFT component were examined, based on the extensive test results conducted by previous researchers and finite element analysis results obtained in this study. Especially, the focus was made on the validation of P-M interaction curves proposed by AISC and EC4. From the results, it was found that the current design codes considerably underestimated the strength of CFT component under general combined axial load and bending. Finally, the modified P-M interaction curve was proposed and successfully verified.

• Structural Engineering and Mechanics
• /
• v.49 no.1
• /
• pp.95-110
• /
• 2014

The study deals with physical modeling of space frame-pile foundation and soil system using finite element models. The superstructure frame is analyzed using complete three-dimensional finite element method where the component of the frame such as slab, beam and columns are descretized using 20 node isoparametric continuum elements. Initially, the frame is analyzed assuming the fixed column bases. Later the pile foundation is worked out separately wherein the simplified models of finite elements such as beam and plate element are used for pile and pile cap, respectively. The non-linear behaviour of soil mass is incorporated by idealizing the soil as non-linear springs using p-y curve along the lines similar to that by Georgiadis et al. (1992). For analysis of pile foundation, the non-linearity of soil via p-y curve approach is incorporated using the incremental approach. The interaction analysis is conducted for the parametric study. The non-linearity of soil is further incorporated using iterative approach, i.e., secant modulus approach, in the interaction analysis. The effect the various parameters of the pile foundation such as spacing in a group and configuration of the pile group is evaluated on the response of superstructure owing to non-linearity of the soil. The response included the displacement at the top of the frame and bending moment in columns. The non-linearity of soil increases the top displacement in the range of 7.8%-16.7%. However, its effect is found very marginal on the absolute maximum moment in columns. The hogging moment decreases by 0.005% while sagging moment increases by 0.02%.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.1
• /
• pp.5-15
• /
• 2020

Dynamic behavior of pile foundation is significantly influenced by the dynamic interaction between soil and pile. Especially, in the sloping ground, the soil-pile interaction becomes very complex due to different resistance according to loading direction, soil residual displacement and so on. In this study, dynamic centrifuge tests were performed on the piles in the sloping ground. The model structures consisted of a single pile and 2×2 group pile. The soil-pile interaction has been investigated considering various conditions such as slope, single and group piles, and amplitude of input motions. The phase differences between soil and pile displacement and dynamic p-y curves were evaluated. The analysis results showed that the pile behavior was largely influenced by the kinematic forces between soil and pile. In addition, the dynamic p-y curve showed the complex hysteresis loop due to the effect of slope, residual displacement, and kinematic forces.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.4
• /
• pp.760-780
• /
• 1988

Using the fatigue test results obtained in the SAE Fatigue Cumulative Damage Test Program, prediction methods of fatigue crack initiation life for notched members undergoing random loaming histories were discussed in detail. Conventional fatigue life predictions based on so-called modified Miner's rule were found to be apt to give nonconservative estimate, due to lack of sufficient consideration for stress-interaction effect. A modified .epsilon.-N curve concept was proposed to account for the stress-interaction effect. The predicted fatigue life based on the modified .epsilon.-N curve concept was in good agreement with the experimental results of SAE Test Program. Specifically for the cases when fatigue data was not available at hand, was proposed a procedure to give conservative estimate of fatigue life.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1992.04a
• /
• pp.80-85
• /
• 1992

A nonlinear second-order analysis program that properly describes the nonlinear behavior of concrete was developed by using the layering technique. As the slenderness ratio of column is increased, the peaks of P-M curve lie remote from the section interaction diagram for the same eccentricities. But the peaks of P-M curve lie rather close to the section interaction diagram for very large eccentricities. In this study , the effects of compressive strength of concrete, longitudinal steel ratio, and yield strength of steel on second-order moment of concrete columns were analyzed. As the compressive strength of concrete and the yield strength of steel are increased, the ratio of peak axial force to maximum axial strength for concentrically loaded short column( Pu/Po) is decreased. But as the longitudinal steel ratio is increased, the ratio , Pu/Po increases.

• Structural Engineering and Mechanics
• /
• v.32 no.2
• /
• pp.321-335
• /
• 2009

When a roof frame is subjected to the airblast loading, the conventional way to analyze the damage of the frame or design the frame is to use single degree of freedom (SDOF) model. Although a roof frame consists of beams and girders, a typical SDOF analysis can be conducted only separately for each component. Thus, the rigid body motion of beams by deflections of supporting girders can not be easily considered. Neglecting the beam-girder interaction in the SDOF analysis may cause serious inaccuracies in the response values in both Pressure-Impulse curve (P-I) and Charge Weight-Standoff Diagrams (CWSD). In this paper, an inelastic two degrees of freedom (TDOF) model is developed, based on force equilibrium equations, to consider beam-girder interaction, and to assess if the modified SDOF analysis can be a reasonable design approach.

• Journal of Magnetics
• /
• v.2 no.3
• /
• pp.105-109
• /
• 1997

The Preisach model neds a density function or Everett function for the hysterisis operator to simulate the hysteresis phenomena. To obtain the function, many experimental data for the first order transition curves are required. However, it needs so much efforts to measure the curves, especially for the hard magnetic materials. By the way, it is well known that the density function has the Gaussian distribution for the interaction axis on the Preisach plane. In this paper, we propose a simple technique to determine the distribution function or Everett function analytically. The initial magnetization curve is used for the distribution of the Everett function for the coercivity axis. A major, minor loop and the initial curve are used to get the Everett function for the interaction axis using the Gaussian distribution function and acceptable results were obtained.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.6
• /
• pp.63-69
• /
• 2005

For the case that center crack is surrounded by four small cracks which are symmetrically distributed around center crack, the same values of normalized stress intensity factor of center crack according to the position of the tip of small cracks are located on the smooth curve. And the stress intensity factor according to any position of small cracks can be sufficiently obtained from this curve. The plastic zones between distributed cracks are also investigated by changing the positions of nearly small cracks. The occurrence of plastic zone due to the interaction between center crack and small cracks are analyzed by finite element method. The mechanical behavior at the vicinity of crack tips is investigated by plastic areas. The changes of plastic zones according to positions of distributed cracks are drawn schematically. The safety of materials is also analyzed.

• Geomechanics and Engineering
• /
• v.25 no.2
• /
• pp.123-134
• /
• 2021

In this paper, the carbon fiber reinforced plastic (CFRP) grids embedded in polymer cement mortar (PCM) shotcrete (CFRP-PCM method) was conducted to repair the degraded tunnel linings with a cavity. Subsequently, the reinforcing effect of the CFRP-PCM method under different degrees of lining deterioration was quantitatively evaluated. Finally, the limit state design method of the M-N interaction curve was conducted to determine whether the structure reinforced by the CFRP-PCM method is in a safe state. The main results indicated that when the cavity is at the shoulder, the lining damage rate is more serious. In addition, the remarkably reinforcing effect on the degraded tunnel linings could be achieved by applying a higher grade of CFRP grids, whereas the optimization effect is no longer obvious when the grade of CFRP grids is too high (CR8); Furthermore, it is found that the M-N numerical values of the ten reinforcing designs of the CFRP-PCM method are distributed outside the corresponding M-N theoretical interaction curves, and these designs should be avoided in the corresponding reinforcing engineering.