• Journal of Information Display
• /
• 제7권3호
• /
• pp.5-8
• /
• 2006

A novel a-Si TFT integrated gate driver circuit using multi-thread driving has been developed. The circuit consists of two independent shift registers alternating between the two modes, "wake" and "sleep". The degradation of the circuit is retarded because the bias stress is removed during the sleep mode. It has been successfully integrated in 14.1-in. XGA LCD Panel, showing enhanced stability.

• 전력전자학회논문지
• /
• 제25권1호
• /
• pp.21-28
• /
• 2020

Integrated bidirectional OBC/LDC was developed to reduce the volume for elements, avoid space restriction, and increase efficiency in EV vehicles. In this study, a DC-DC converter in integrated OBC/LDC circuits was composed of an SRC circuit with a stable output voltage relative to an LLC circuit using a theoretical method and simulation. The resonant network of the selected circuit was optimized to minimize the power loss and element volume under constraints for the buck converter and the battery charging range. Moreover, the validity of the optimal model was verified through an analysis using a theoretical method and a numerical analysis based on power loss at the optimized resonant frequency.

• 센서학회지
• /
• 제14권1호
• /
• pp.28-32
• /
• 2005

In this paper, a CMOS integrated detection circuit for capacitive type fingerprint sensor signal processing is described. We designed a detection circuit of charge-sharing sensing scheme. The proposed detection circuit increases the voltage difference between a ridge and valley. The test chip is composed of $160{\times}192$ array sensing cells (12 by $12.7{\;}mm^{2}$). The chip was fabricated on a 0.35 m standard CMOS process. Measured difference voltage between a ridge and valley was 0.95 V.

• ETRI Journal
• /
• 제31권3호
• /
• pp.247-253
• /
• 2009

We propose a Ku-band driver and high-power amplifier monolithic microwave integrated circuits (MMICs) employing a compensating gate bias circuit using a commercial 0.5 ${\mu}m$ GaAs pHEMT technology. The integrated gate bias circuit provides compensation for the threshold voltage and temperature variations as well as independence of the supply voltage variations. A fabricated two-stage Ku-band driver amplifier MMIC exhibits a typical output power of 30.5 dBm and power-added efficiency (PAE) of 37% over a 13.5 GHz to 15.0 GHz frequency band, while a fabricated three-stage Ku-band high-power amplifier MMIC exhibits a maximum saturated output power of 39.25 dBm (8.4 W) and PAE of 22.7% at 14.5 GHz.

• 대한전자공학회논문지
• /
• 제12권2호
• /
• pp.28-30
• /
• 1975

2선식-4선식 접속을 위한 새로운 회로구성을 제안하였다. 이 회로구성은 현재까지 알려져 있는 회로구성과는 달라 전화기잡음방지회로 뿐만 아니라, 전화전송계의 임의의 중계장치에 이용될 수 있다. 이것은 또 IC화한 형태로 실현될 수 있다. In this paper a new network configuration for two-line four-line connection in telephone transmission system is proposed. It is proved that this network configuration is useful not only in an anti-sidatone circuit for telephone substation but also in a repeater station in the telephone system. It can ba realized in an integrated circuit.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.822-824
• /
• 2007

This paper investigated a gate driver circuit with amorphous silicon for mobile TFT-LCD. In the conventional circuit, the fluctuation of the off-state voltage causes the fluctuation of gate line voltages in the panel and then image quality becomes worse. Newly designed gate driver circuit with dynamic switching inverter and carry out signal reduce the fluctuation of the off-state voltage because dynamic switching inverter is holding the off-state voltage and the delay of carry signal is reduced. The simulation results show that the proposed a-Si:H gate driver has low noise and high stability compared with the conventional one.

• Journal of Electrical Engineering and Technology
• /
• 제7권2호
• /
• pp.221-224
• /
• 2012

We propose a Readout Integrated Circuit (ROIC), which applies a fixed current bias sensing method to the input stage in order to simplify the circuit structure and the infrared sensor characteristic control. For the sample-and-hold stage to display and control a signal detected by the infrared sensor using a two-dimensional (2D) focal plane array, a differential delta sampling (DDS) circuit is proposed, which effectively removes the FPN. In addition, the output characteristic is improved to have wider bandwidth and higher gain by applying a two-stage variable gain amplifier (VGA). The output characteristic of the proposed device was 23.91 mV/$^{\circ}C$, and the linearity error rate was less than 0.22%. After checking the performance of the ROIC using HSPICE simulation, the chip was manufactured and measured using the SMIC 0.35 um standard CMOS process to confirm that the simulation results from the actual design are in good agreement with the measurement results.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -1
• /
• pp.235-237
• /
• 2002

As the integrated circuit technology gets developed, a circuit size of more than thousands of transistors becomes normal. A hierarchical design is unavoidable due to a huge circuit size. It is important how we can consider hierarchical structure in circuit delay analysis. In this paper we present an accurate method to analyze the delay of circuit with hierarchical structure. Adding the notion of global false path to the hierarchical timing analysis performs more accurate timing analysis.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(5)
• /
• pp.247-250
• /
• 2002

This paper proposes a PWM circuit using CMOS OTAs. The features of the proposed PWM circuit are IC oriented circuits, simple configuration, and bias current controlled output. In order to verily the validity of the proposed circuit, it is simulated by H-SPICE program. Futhermore, the proposed circuit is integrated on chip using 0.35 $\mu\textrm{m}$ CMOS technology.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 1993년도 Fifth International Fuzzy Systems Association World Congress 93
• /
• pp.925-928
• /
• 1993

In this paper the caracteristics of the fuzzy flip-flop which was proposed as a fuzzy sequential circuit is firstly mentioned. Secondly the circuit construction of typical fuzzy flip-flip circuits using VHDL (Very high speed integrated circuit Hardware Description Language) compiler and simulator is presented. Finally the possibility of the application of the fuzzy sequential circuit will be mentioned.