• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.29 no.2
• /
• pp.67-76
• /
• 2017

In this study, the effect of caisson heel on the active earth pressure is investigated. Using limit analysis method, inclinations of slip surface developed above the heel with different lengths are analyzed. The shorter the heel length, the larger those of inside slip surface, however those of outside slip surface are not changed. According to the relative heel length, relationships of internal friction angle of backfill material - wall friction angle between caisson structure and backfill - friction angle acting on virtual section at the end of heel are presented. Earth pressures acting against caisson structure with relatively short heel are smaller than Rankine earth pressure but always greater than Coulomb earth pressure which does not consider the heel length.

• KSTLE International Journal
• /
• v.7 no.2
• /
• pp.51-55
• /
• 2006

In order to design an effective foot surface which can provide adequate friction for a self-propelled medical microrobot moving inside the small intestine, frictional mechanisms between the small intestine inner wall and the foot surface of the robot must be understood. In this paper, mechanical interlocking effect was considered to design the surface of the foot that can generate the desired frictional force. The concept of the design was derived from the hookworm that lives inside the small intestine. Hookwarms are known to adhere to the small intestine wall by interlocking with villi on the surface of the small intestine. The interlocking mechanism was considered as the main frictional mechanism for the design of the microrobot foot surface in this work. 2 mm and 6 mm diameter solid and hollow cylindrical shaped foot specimens were designed and tested to assess the frictional force between the specimens and the porcine small intestine specimen.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.7
• /
• pp.91-97
• /
• 2001

When a body including a crack inside is subjected to the compressive forces, the crack is closed and sliding occurs on the crack surfaces. In this work, a subsurface crack subjected to a static compressive load is analyzed with the finite element method considering friction on the crack surface. The friction on the crack surface is assumed to follow the Coulomb friction law, and a numerical method based on the finite element method and iterative method is applied in this work. The result is compared with those of ANSYS and references.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.107-109
• /
• 1998

This paper presents mechanical analysis of gas turbine generator (113MVA, $3{\phi}$, 2P, 0.9PF, F class, 3600rpm, 60Hz, 13.8kV, 4.72kA, Air-Cooling) field coil deformation. Rotor end coil deformation is only appeared on turbine end but collector end coil is normal. Expansion direction of end coil is tangential not axial. Deformation appears more severe at top turn. Retaining ling is expanded by centrifugal force of coil and itself. In case friction coefficient between coil top surface and retaining ring insulation inner surface is small, coil end length ${\ell}$ does not change. However, in case friction coefficient big condition, coil end is expanded ${\Delta}{\ell}$ due to start and stop. Deformation is assumed about 30mm by watching photograph inner surface of retaining ring is coated by Teflon at manufacturing condition. Usually Teflon coating insulation surface is small friction coefficient. It's value 0.08${\sim}$0.15. However it's value exceeds more than 0.297. Since top turn deformation appears. The distortion and subsequent failure have occurred because of the lack of a sufficient slip-plane between the top field coil conductors and the inside surface of the retaining ring insulation on the turbine end of the field-winding.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.60-63
• /
• 2000

In this study, efficient force reflection algorithm is developed for the Haptic Display by using a proxy concept and friction model. When there are not any contacted obstacles the proxy is following human operator's command trajectory in the 3D virtual space. But when the operator's command trajectory is locating inside of the object, the proxy is constrained by the surface of the object. Here only with the information of the proxy position and operator's command trajectory at every time step, we can calculate the reflection force and its orientation. To display the friction force between two virtual stiff material which are sliding against each other, modified Karnopp's friction model is used. In the friction model, a damping term and a Stribeck effect term are included to display the relative velocity effect and stick-slip effect at the very low relative velocity region respectively.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.4
• /
• pp.318-324
• /
• 2005

The objectives of this paper are to study the heat transfer characteristics on enhanced surfaces, to develop experimental correlations of friction factor and Nusselt number, and to provide a guideline for optimum operation conditions at low temperature boiling for practical refrigeration applications. The working fluid (water, EG $30\%$) flows inside the enhanced tube and R134a boils on the outer surface. Two different types of Turbo-B tubes (Tube I and Tube II) are tested in the present study. The results show that Tube I gives a higher heat transfer coefficient with higher friction factor than Tube II. The present study provided experimental correlations for friction factor and heat transfer coefficient with error bands of ${\pm}5\%\;and\;{\pm}\;15\%$, respectively.

• Journal of computational fluids engineering
• /
• v.14 no.4
• /
• pp.56-61
• /
• 2009

This study deals with the numerical investigation on two-dimensional lubrication characteristics of micro-dimple shapes fabricated on solid surfaces by using the commercial CFD code (Fluent V.6.3) to examine the influence of micro dimple depth and width on the reduction in friction under the sliding plate condition. In addition, single and multiple dimple arrays are simulated, all for a fixed area fraction of dimple on the surface. As a result, it is found that the existence of micro-dimpled surface makes it possible to substantially reduce the friction forces exerted on the surfaces, and such an optimum dimple depth would be present because the dimple depth larger than the optimum value did no longer affect the reduction in shear stresses, indicating that the reduction of friction is likely to be associated with inner flows of lubricant inside dimples. Moreover, it is observed that at the fixed area fraction, the friction reduction increases with the increase of dimple diameter.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.255-256
• /
• 2002

In this paper, the frictional behavior according to the contact geometry was investigated using a micro-tribotester built inside a Scanning Electron Microscope (SEM) and an Atomic Force Microscope (AFM). FFT (Fast Fourier Transform) analysis for friction was conducted as a method to interpret the contact condition. From the experimental results, it could be concluded that the relative dimensions and distribution of contact asperities on the surface could be predicted by the power spectrum and main frequency in the FFT analysis of the friction signal.

• Journal of Korean Society of Steel Construction
• /
• v.10 no.1 s.34
• /
• pp.101-113
• /
• 1998

In this study, we research the influence of butt-welded joints in high tension bolted joints on the static and fatigue strength. As a results, if it's located inside or outside of the friction surface, the fatigue strength decrease, and the decrease of fatigue strength is greater in cases that the butt-welded joints exist outside of the friction surface. But the influence of butt-welded joint on the fatigue strength satisfies category B of the Specifications.

• Journal of Korean Society of Steel Construction
• /
• v.9 no.3 s.32
• /
• pp.421-430
• /
• 1997

In this study, the static and the fatigue tests were performed with high tension bolted joints, of which the surfaces were spread with inorganic zinc-primer after shot-blast, and milling surface, and steel-natural surface, difference of friction surface condition were examined by comparing the esults of tests. From the result of synthetical investigation of this study. it is proper that using the torque management method in order to introduce design axial force to blots, and the provision of specifications that initial axial forces must be 110% of design axial forces is proper. Decreasing ratio of axial forces to initial force is proportional to common lorgarithms of time progress, it converge constant value after 20 hours, and decreasing ratio is little related to the roughness of friction surface. Sliding coefficient of milling, spreading inorganic zinc-primer, just producting is great in order and sliding forces are dependent on the applied axial forces, but if the applied axial forces are great, sliding coefficient become small by a loss of roughness. So it is confirmed that relation between the applied axial forces and the sliding forces are not proportional linearly. From the result of estimation on fatigue strength, all specimens satisfy the specifications with B-grade and milling surface is lower than the others about 14% in fatigue strength because in milling surface lose the function of friction-types joints at lower number of cycles. From the result of eximination for the distribution area of compressive force, friction area near to inside bolt is wider in the direction of stress than near to outside. It is guessed that this situation occurs because outside bolts firstly change from the friction connection to the bearing connection.