• 전자공학회논문지C
• /
• 제34C권7호
• /
• pp.28-37
• /
• 1997

In this paper, we designed a motion estimator for MPEG-2 video coder using VHDL. Motion estimation is indispensable for encoding MPEG 2 video. Motion estimation takes over 50% computation power of video encoding 37 frames per second and is suitable for real-time processing. The number of data accesses for computation is fewer than 2 times compared with that of old one. This makes slower memory module available. We minimize input pins to migrate input data through PEs. This processor can compute various motio estimation modes at one calculation that is supported by MPEG-2 video standard. Also independent control architecture makes this processor a single processor or a sub module in amultimedia chip.

• Journal of Communications and Networks
• /
• 제7권3호
• /
• pp.284-293
• /
• 2005

A critical issue in applications involving networks of wireless sensors is their ability to synchronize, and mitigate the fading propagation channel effects. Especially when distributed 'slave' sensors (nodes) reach-back to communicate with the 'master' sensor (gateway), low power cooperative schemes are well motivated. Viewing each node as an antenna element in a multi-input multi-output (MIMO) multi-antenna system, we design pilot patterns to estimate the multiple carrier frequency offsets (CFO), and the multiple channels corresponding to each node-gateway link. Our novel pilot scheme consists of non-zero pilot symbols along with zeros, which separate nodes in a time division multiple access (TDMA) fashion, and lead to low complexity schemes because CFO and channel estimators per node are decoupled. The resulting training algorithm is not only suitable for wireless sensor networks, but also for synchronization and channel estimation of single- and multi-carrier MIMO systems. We investigate the performance of our estimators analytically, and with simulations.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 D
• /
• pp.2182-2184
• /
• 2004

This paper presents a systematic and straightforward fault estimation approach for process fault detection. isolation and accommodation. The approach includes the design of a reduced-order observer and an algebraic-fault estimator. The observer is designed for an unknown input and fault-free system, which is obtained by coordinate transformations of original systems with unknown inputs and faults. The observer information is devoted to- the fault estimation for fault detection and isolation. The fault estimates can be used to form an additional control input to accommodate the fault. The suggested scheme is verified through simulation studies performed on the control of a vertical takeoff and landing (VTOL) aircraft in the vertical plane.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.110-110
• /
• 2001

By the state transformation including independent outputs functions, a nonlinear process model can be decomposed into two subsystems; the one(design model) is described in output variables as new states and used for control system synthesis and the other(disturbance model) is described in the original unavailable states and its couplings with the design model are treated as uncertain time-varying parameters in the design model. Its existence with respect to the design model is ignored. So, the design model is and uncertain time-variant system. Control synthesis based on a reduced design model is a combined form of a time-variant input-output linearization with parameter estimation. The parameter estimation is also based on the design model and it gives the parameter estimates such that the estimated outputs follow the actual outputs in a specified way. The disturbances form disturbance model and as well all the other uncertainties affecting the outputs will be reflected into the estimated parameters used in the linearizing control law.

• 한국물환경학회지
• /
• 제21권6호
• /
• pp.575-583
• /
• 2005

In this study the flow curve estimation is discussed using TANK model which is one of hydrologic models. The main interest is the accuracy of TANK model parameter estimation with respect to the sampling frequency of input data. For doing this, input data with various sampling frequencies is used to estimate model parameters. As a result, in order to generate relatively accurate flow curve, it is recommendable to measure stream flow at least every 8 days.

• International Journal of Control, Automation, and Systems
• /
• 제4권5호
• /
• pp.529-538
• /
• 2006

Separating a reentry vehicle into warhead and body is a conventional and efficient means of producing a huge decoy and increasing the kinetic energy of the warhead. This procedure causes the radar to track the body, whose radar cross section is larger, and ignore the warhead, which is the most important part of the reentry vehicle. However, the procedure is difficult to perform using standard tracking criteria. This study presents a novel tracking algorithm by integrating input estimation and modified probabilistic data association filter to solve this difficulty in a clear environment. The proposed algorithm with a new defined association probability in this filter provides a good tracking capability for the warhead ignoring the radar cross section. The simulation results indicate that the errors between the estimated and the warhead trajectories are reduced to a small interval in a short time. Therefore, the radar can produce a beam to illuminate to the right area and keep tracking the warhead all the way. In conclusion, this algorithm is worthy of further study and application.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -3
• /
• pp.1799-1802
• /
• 2002

This paper proposes an improved method for formant frequencies estimation based on the complex autocorrelation function of the speech signal. Instead of using the incoming signal as an input fur the LPC analysis, the analytic signal of the autocorrelation function of the speech signal is computed and itself used as an input for the LPC analysis. Due to the properties of the analytic signal, which occupies half of the bandwidth of the original signal, the required model order for the LPC analysis is halved. The accuracy of the proposed method in noisy environments is examined on five natural vowels. The effectiveness of the proposed method is shown by the estimated spectral shapes and the estimation errors of the formant frequencies.

• 전기학회논문지P
• /
• 제63권4호
• /
• pp.241-247
• /
• 2014

This paper propose a variable parameter estimations of five-phase squirrel-cage induction motor(IM) for speed control system. In order to high performance control of AC motor using a field oriented control(FOC) and direct torque control(DTC) algorithm, there are required precise motor parameters for slip calculation, flux observer, controller gain, rotor position, speed estimation, and so on. We are suggest a analyzed estimation results of the motor parameters that developing five-phase squirrel-cage IM have a stator of concentrated winding for experimental of variable input power frequency. There are results of stator winding test, no-load test, locked-rotor test, variable actual load test, and estimated parameters of equivalent circuits using manufactured experimental apparatus by IEEE Standard Test Procedure for Polyphase Induction Motors and Generators 112-2004.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 D
• /
• pp.2545-2547
• /
• 2000

In this paper, a hybrid fuzzy controller using genetic algorithm based on parameter estimation mode to obtain optimal control parameter is presented. First, The control input for the system in the HFC is a convex combination of the FLC's output in transient state and PID's output in steady state by a fuzzy variable, namely, membership function of weighting coefficient. Second, genetic algorithms is presented to automatically improve the performance of hybrid fuzzy controller utilizing the conventional methods for finding PID parameters and estimation mode of scaling factor. The algorithms estimates automatically the optimal values of scaling factors, PID parameters and membership function parameters of fuzzy control rules according to the rate of change and limitation condition of control input. Computer simulations are conducted to evaluate the performance of proposed hybrid fuzzy controller. ITAE, overshoot and rising time are used as a performance index of controller.

• ETRI Journal
• /
• 제29권5호
• /
• pp.607-613
• /
• 2007

Most signal-to-noise ratio (SNR) estimation techniques in digital communication channels derive the SNR estimates solely from samples of the received signal after the matched filter. They are based on symbol SNR and assume perfect synchronization and intersymbol interference (ISI)-free symbols. In severe channel distortion where ISI is significant, the performance of these estimators badly deteriorates. We propose an SNR estimator which can operate on data samples collected at the front-end of a receiver or at the input to the decision device. This will relax the restrictions over channel distortions and help extend the application of SNR estimators beyond system monitoring. The proposed estimator uses the characteristics of the second order moments of the additive white Gaussian noise digital communication channel and a linear predictor based on the modified-covariance algorithm in estimating the SNR value. The performance of the proposed technique is investigated and compared with other in-service SNR estimators in digital communication channels. The simulated performance is also compared to the Cram$\acute{e}$r-Rao bound as derived at the input of the decision circuit.