• Journal of Acupuncture Research
• /
• v.17 no.2
• /
• pp.139-152
• /
• 2000

This study was designed to evaluate the analgesic effect of bee venom (BV) Acupuncture into different treatment points, Chok-samni (ST36) and blank loci of the gluteal muscle and back. We investigated the changes in formalin-induced pain behavior according to the pretreatment with different concentrations of BV, thirty minutes before the formalin injection. The results were summarized as follows: 1. The formalin-induced pain behavior was suppressed by pretreatment with BV into Chok-samni (ST36) in a dose dependent manner. During the early phase, 0.08mg/kg of BV showed a statistically significant suppression in the formalin-induced pain behavior. Moreover, 0.008mg/kg, 0.016mg/kg, and 0.08mg/kg of BV, except 0.0016mh/kg of BV, had significant suppresive effects on the formalin-induced pain behavior during the late phase. Therefore, these data indicated that the suppressive effect of BV acupuncture on the formalin-induced pain behavior was stronger in the late phase rather than the early phase 2. In order to investigate the analgesic effect of BV acupuncture into different treatment points, the experimental animals were divided into three groups: Chok-samni (ST36) group, gluteal group and back group. In the Chok-samni (ST36) group, the formalin-induced pain behavior during all the phases was significantly reduced as compared with that of the back group. However, as compared with that of the gluteal group, the formalin-induced pain behavior in the Chok-samni (ST36) group was decreased only in the late phase, not in the early phase. The formalin-induced pain behavior in the gluteal group was significantly reduced as compared with that of the back group in the late phase, not in the early phase. We suggested that the analgesic effect of BV acupuncture into Chok-samni (ST36) was most effective among Chok-samni (ST36), gluteal, and the back groups in formalin-induced pain behavior.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.213-216
• /
• 2007

LGP (light guide plate) of LCD-BLU (Liquid Crystal Display - Back Light Unit) is one of the major components which affects the product quality of LCD. In the present study, the optical patterns of LGP(2.2") are manufactured by three different methods, namely, laser ablation, chemical etching and LiGA - reflow, respectively. The pattern surface images and roughness of mold and product were compared to check the optical characteristics. From the results of measurement the optical patterns fabricated by LiGA - reflow method showed the best geometric structure as intended in design and the lowest roughness among those.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.3
• /
• pp.376-380
• /
• 2006

Temperature distribution measured to estimate the condition of an electrical apparatus is an absolute reference for the apparatus conditions and the difference between the reference temperature and the current temperature. Because of passive thermography, without the external thermal stimulation, the difference in surface temperature between the region of interest and back ground shows that the results can apply only to the estimation or the monitoring for the condition of loose terminal and the overload pertaining to the rise in temperature. However, a thermal diffusion in the active thermography is differently generated by the structure and condition of the surface and subsurface. This paper presents a nondestructive test using this behavior and deals with the results by heat injection and cooling to the apparatus. The buried discontinuity of subsurface could be detected by these techniques.

• The Journal of Korean Physical Therapy
• /
• v.20 no.3
• /
• pp.69-74
• /
• 2008

Purpose: The majority of patients with radiculopathy caused by a herniated nucleus pulposus (HNP) heal spontaneously without surgery. The aim of this report is to describe the spontaneous regression of lumbar disc herniation and the results of clinical follow-up. Methods: Three patients with radiating low back pain presented with an extruded intervertebral disc on magnetic resonance imaging (MRI). We performed follow-up with conservative treatment (epidural injection, medication, physical therapy, exercise) and clinical assessments on the 6th, 10th and 22nd months. Results: The extruded intervertebral disc almost complete regressed, and correlated with clinical improvement and follow-up MRI. Conclusion: Conservative treatment can be an effective approach for a herniated lumbar discs if no neurological deficits are present.

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.4
• /
• pp.188-191
• /
• 2012

This paper introduces a new method regarding deuterium incorporation in the gate dielectric including deuterium implantation and post-annealing at the back-end-of-the process line. The control device and the deuterium furnace-annealed device were also prepared for comparison with the implanted device. It was observed that deuterium implantation at a light dose of $1{\times}10^{12}-1{\times}10^{14}/cm^2$ at 30 keV reduced hot-carrier injection (HCI) degradation and negative bias temperature instability (NBTI) within our device structure due to the reduction in oxide charge and interface trap. Deuterium implantation provides a possible solution to enhance the bulk and interface reliabilities of the gate oxide under the electrical stress.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.119-120
• /
• 2016

회전자 자속기준 벡터제어(FOC)의 센서리스의 기법은 다양하지만, 크게 역기전력을 이용하는 방식과 인덕턴스를 기반으로 하는 방식으로 나눌 수 있다. 역기전력을 기반으로 하는 기법은 중속이상의 영역에서는 뛰어난 성능을 보이지만, 저속영역에서 역기전력이 작기 때문에 저속에서 불리함이 있다. 반면, 인덕턴스를 기반으로 하는 기법 중 캐리어 신호를 주입하는 기법은 전동기의 자기적 돌극성(Magnetic saliency)을 이용하므로 저속에서도 사용가능하지만, 고속에서는 전압제한으로 인하여 전압주입에 불리함이 있으며, 고주파잡음의 문제가 있다. 따라서 본 논문은 저속영역에서 사각파 형태의 고주파 주입 센서리스기법을 사용하고, 중속이상의 영역에서 역기전력 센서리스기법으로 절환(Crossover)하는 방식을 제안한다. 기존의 속도추정 기법과 제안하는 기법을 시뮬레이션을 통해 비교한다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1233-1235
• /
• 2004

We have designed High Performance Prism LGP in 17 inch TFT-LCD. In test result to embody high brightness BLU in case of LGP of base and upper surface with 17 inch, thickness 8mm adding prism construct, it is superior brightness improvement than previous that of printing form about some 20% and in this course to embody actual material it succeeded prism LGP production by 17 inch injection form process.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.9
• /
• pp.56-62
• /
• 1999

The disintegration of transient diesel spray in early was investigated at different opening pressure and chamber pressure by measns of shadowgraph method using nanolite and still camera. Diesel spary was injected into the spray chamber which was charged with high pressure nitrogen gas. Atthe begining of injection, a liquid column that was almost the same diameter as the nozzle hole was observed . Spray tip penetration and spray angle were always increased with an increase in opening pressure.

• 한국생물공학회:학술대회논문집
• /
• 2001.11a
• /
• pp.791-795
• /
• 2001

This study was conducted to develop a new biomaterial to be used for skin whitening. The melanin elimination effect of chondroitin sulfate and phelinus linteus mushroom in rabbit back skin were evaluated. Rabbit dorsum was exposed to chronic UV irradiation(320nm) once daily for 30 days after initial melanin injection (100mg/kg). And then, chondroitin sulfate and phelinus linteus mushroom at dose of 0.7g for 30days were applied on the zone. The dorsal skin was histologically examined. Furthermore, we investigated free-radical extinction effect, antioxidation and tyrosinase activity inhibition effects. The histological study indicated that chondroitin sulfate and phelinus linteus mushroom decreasd melanine pigment significantly. As a result, chondroitin sulfate and phelinus linteus mushroom have a remarkable effect on the skin whitening by melanin elimination.

• Transactions of the Korean hydrogen and new energy society
• /
• v.4 no.1
• /
• pp.1-9
• /
• 1993

To find performance and knock limit for compression ratio in hydrogen fueled engine, the variable compression ratio hydrogen fueled engine which was able to vary compression ratio during firing was manufactured and estimated. The characteristics of the variable compression ratio hydrogen fueled engine were as follows : 1) compression ratio variation by moving of cylinder head, 2) OHC which can be realized low S/V ratio, short flame propagation distance and unvariable configuration of combustion chamber for compression ratio variation, 3) direct injection of hydrogen gas to restrict back fire.