• Journal of Labour Economics
• /
• v.33 no.3
• /
• pp.1-23
• /
• 2010

Extension of mandatory retirement age (MRA) differs from other labor supply increases in that it induces a change in the incentive to save for retirement. A simple general equilibrium model indicates that extension of MRA can lead to a decrease in life-time income and social welfare as it excessively discourages domestic savings and thus capital accumulation. However, in an open economy where capital inflow allows capital input in production to remain constant despite lower domestic capital stock, extension of MRA likely increases worker welfare. In such case, extension of MRA can contribute to expansion of hiring demands through lowering wages or mitigating upward pressures on wages.

• Journal of Environmental Science International
• /
• v.18 no.9
• /
• pp.941-952
• /
• 2009

The urban microscale wind field around the air quality monitoring station was investigated in order to check how a building complex influences it. For this study as the high density areas Jwa-dong and Yeonsan-dong monitoring sites in Busan were chosen. As the direction of inflow which is perpendicular to the building of the monitoring station was expected to cause the considerable variation of the wind field, that direction was selected. The model Envi-met was used as the diagnostic numerical model for this study. It is suitable for this investigation because Envi-met has the microscale resolution. After simulating it, on the leeward side around a building complex the decrease of flow velocity and some of vortexes or circulation area were discovered. In addition, on the edge of the top at the building and at the back of the building the upward flow was developed. If the sampling hole of monitoring site were located in this upward flow, it would be under the influence of upward flow from the near street.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.12
• /
• pp.1588-1595
• /
• 2000

Natural convection heat transfer in an enclosure with an opening in the right veritcal wall and a heat source at the bottom surface is investigated using a holographic interferometric technique. The effects of the opening length, divider length attached to the top wall, and heater temperature on the temperature distribution are examined. The opening length as well as the divider length greatly affects the degree of inflow and outflow of air. In the case of small opening length, the opening doesnt affect much the upward warm air flow resulting in the symmetric temperature distribution .The upward flow in hindered by the divider resulting in the decrease of heat transfer from the heater region to the upper region. The longest divider shows the highest temperature in the lower region of enclosure. In the case of large opening length, the inward cold flow moves the upward flow to the left direction. Among the cases of different divider length, the case of H(sub)d=0.25H shows the highest temperature in the lower region of enclosure.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.6
• /
• pp.487-497
• /
• 2011

Numerical analysis has been performed to investigate the rotor speed and pitch range variations when the airspeed is increased in autorotation. Transient Simulation Method(TSM) was used to obtain the steady states of autorotation. The rotor blade was analyzed by the two-dimensional compressible Navier-Stokes solver in order to adapt to the airspeed increase and the results were used in the transient simulation method. Meanwhile, the Pitt/Peters inflow theory was used to supply the induced velocity fields. For the prescribed torque equilibrium state, the combinations of velocity, shaft angle, and pitch angle were produced to investigate the rotor speeds and variable ranges. The rotor tip Mach number and rotor speed were correlated and the trim range of pitch angle was observed with respect to the shaft angle decrease.

• Journal of Korean Society of Rural Planning
• /
• v.19 no.4
• /
• pp.203-212
• /
• 2013

The aging of farm households has caused serious problems such as productivity slowdown and aggravated income polarization in South Korea. Urban-to-rural migration has been recently suggested as a measure to attenuate the aging of rural population and other related problems. The inflow of migrants for farming can have a substantial effect on agriculture and rural communities while the natural adjustment of rural population caused by birth and death is slow. This paper forecasts population distribution of different provinces using the Origin-Destination (OD) analysis, taking into account both the size and directions of migration. In the analysis, nodes where the migration takes place are divided by the industrial sectors (agriculture and non-agriculture), regions, and ages. The results of a ten-year forecast shows that the aging of total population in most provinces will be intensified, but the portion of people over sixty will decrease in the agricultural sector. This finding implies that migration into rural areas, when occurring by a large extent, can mitigate the aging process and attendant problems.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.14 no.1
• /
• pp.1-9
• /
• 2016

In this study, thermal-hydrological-chemical modeling for the alteration of a bentonite buffer is carried out using a simulation code TOUGHREACT. The modeling results show that the water saturation of bentonite steadily increases and finally the bentonite is fully saturated after 10 years. In addition, the temperature rapidly increases and stabilizes after 0.5 year, exhibiting a constant thermal gradient as a function of distance from the copper tube. The change of thermal-hydrological conditions mainly results in the alteration of anhydrite and calcite. Anhydrite and calcite are dissolved along with the inflow of groundwater. They then tend to precipitate in the vicinity of the copper tube due to its high temperature. This behavior induces a slight decrease in porosity and permeability of bentonite near the copper tube. Furthermore, this study finds that the diffusion coefficient can significantly affect the alteration of anhydrite and calcite, which causes changes in the hydrological properties of bentonite such as porosity and permeability. This study may facilitate the safety assessment of high-level radioactive waste repositories.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.50 no.1
• /
• pp.13-21
• /
• 2008

Water losses in irrigation canals are mainly estimated as the sum of conveyance and delivery water loss. The losses occur via the evaporation, infiltration, gate operation and water distribution processing. Recently, the study regarding these water losses are not satisfactory enough, also delivery water loss has not been mainly considered on field design. The objective of this study is to investigate and analyze the volume of water loss in irrigation canals considering condition of actual farm land. A field measurement was performed at four research sites, which are managed by Korea Rural Community & Agriculture Corporation, to evaluate conveyance and delivery water loss for 2 years. The measurement was performed by canal type, size and designed flow using the inflow-outflow method at a major points such as start and end of each canal, derivation point of canal and inlet of paddy fields. Results of this study showed that water loss ratio in lateral canals was bigger than that of main canal unlike current design standard and the loss decrease as flow increase. The total of water loss ratio including conveyance and delivery water loss in several irrigation canals ranged between 33.25 and 45.0%.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.3
• /
• pp.268-278
• /
• 2009

The present study focused on evaluation for the performance of the Flow Control Flat Plate (FCFP) attached in the stern side of the ship. The important function of this FCFP is to enhance the resistance performance through the decrease of stern sinkage and the propulsive performance by the adjustment of inflow velocities in the propeller plane. Two different hull forms were considered to identify the effects of the FCFP. The attachment position, the angle and the size of the FCFP were studied in this numerical simulation. In this paper, the roles of the FCFP were intended to analyze fully through the numerical interpretation.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.7 no.4
• /
• pp.51-60
• /
• 1987

A two dimensional negatively buoyant flow from a shallow channel into rectangular ponds is analysed numerically by a finite difference scheme in a stretched coordinate system. In rectangular ponds, the confuguration of plunge flow largely depends on the densimetric Froude number, $Fr_e$, of the inflow. The velocity of front of the plunging flow increases with increasing negative buoyanty(decrease of $Fr_e$). The location of stable plunge point and maximun travel distance of plunge point are found to be a function of dimensionless time and densimetric Froude number. Large vortices develop on the both sides of negative buoyant flow or plunge flow.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.17 no.1
• /
• pp.1-6
• /
• 2009

The optimum design of back pressure chamber is one of the most important factors in designing scroll compressors because it has a great influence on the efficiency and other design parameters. The design process can be divided into 2 parts. One is obtaining the optimum pressure of the chamber and keeping it in constant value. The other is finding out the minimum inflow rate of medium with which back pressure chamber is filled. In this study we are focused on the first step. At first we added a simple structure that can change back pressure without reassembling compressor. It makes possible to obtaining optimum back pressure. Then we designed an equipment that the back pressure control valve assembly could be independently tested with. Spring was redesigned to decrease stiffness variation. Also sealing mechanism of back pressure control valve was improved to more effective way. As a result, it was verified that in a real mode test back pressure variation could be retained in 2.3% with discharge pressure and operating frequency varied. In addition the integrated structure of back pressure control valve is expected to contribute to effective manufacturing process.