• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.6
• /
• pp.819-828
• /
• 2001

The operating point of a small-sized axial fan is strongly dependent upon the system resistance. Therefore, the turbulent flow characteristics around a small-sized axial fan may change significantly according to the operating point. This study represents three-dimensional turbulent flow characteristics around a small-sized axial fan measured at the ideal design point $\phi$=0.25, which is equivalent to the maximum total efficiency point, by using three dimensional fiber-optic type LDA system. This LDA system is composed of a 5 W Argon-ion laser, two optics in back-scatter mode, three BSAs, a PC, and a three-dimensional automatic traversing system. A kind of paraffin fluid is used to supply particles by means of fog generator. Mean velocity profiles downstream of a small-sized axial fan along the radial distance show that the streamwise and the tangential components exist in a predominant manner, while the radial component has a small scale distribution and shows the inflection which its flow direction is inward or outward. Moreover, the turbulent intensity profiles show that the radial component exists the most greatly among turbulent energies.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.3 s.174
• /
• pp.761-768
• /
• 2000

In order to investigate how the fatigue damage effects on the critical properties of superconductor, a fatigue test at room temperature and an Ic measurement test at 4.2K were carried out in this study, respectively, using a 9 strand Cu-Ni/NbTi/Cu composite cable. Through the fatigue test of a 9 strand Cu-NUNbTi/Cu composite cable, a conventional S-N curve was plotted even though there was a possibility of fretting among strands. It was found that the maximum stress corresponding to the inflection point on the S-N curve obtained was nearly the same value as the yielding strength of cable obtained from the static tensile test. However, the effect of cabling in multi-strands superconducting cable on the fatigue strength was not noticeable. The critical current(Ic) measurement was carried out at 4.2K in a NbTi strand out of the fatigued cable. It showed a degradation of lc at high stress amplitude regions over 380NTa, and the degradation became significant as the applied stress amplitude increased.

• Transactions of Materials Processing
• /
• v.8 no.6
• /
• pp.576-582
• /
• 1999

The high temperature behavior of Al 6061 alloy was characterized by the hot torsion test in the temperature ranges of 400∼550℃ and the strain rate ranges of 0.05∼5/sec. To decide optimum deformation condition, three types of deformation maps were individually made from the critical strain (εc). deformation resistance(σp) and deformation efficiency (η). The critical strain(εc) for dynamic recrystallization (DRX) which was decided from the inflection point of strain hardening rate(θ) - effective stress (σ) curve was about 0.65 times of peak strain (εp). The relationship among deformation resistance (peak stress, σp), strain rate (ε), and temperature (T) could be expressed by ε=2.9×1013[sinh(0.0256σp]7.3exp (-216,000/RT). The deformation efficiency (η)which was calculated on the basis of the dynamic materials model (DMM) showed high values at the condition of 500∼550℃, 5/sec for 100% strain. The results from three deformation maps were compared with microstructures. The best condition of plastic deformation could be determined as 500℃ and 5/sec.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.975-978
• /
• 2001

For machining auto-mobile cam, the developed biarcs-fitting method eliminates the ridge problems in conventional straight-line fitting approximation or single-arc fitting of curve tool path where it leaves ridges of tool marks on the machined surface of the workpiece. The powerful advantage of this biarc method is demonstrated by applying it to the numerically controlled machining of a curved cam profile, also verified by using a CNC simulating program for auto-mobile cam profile. As a result, this algorithm may be used in CNC milling and turning for cam profile machining with short block line.

• Journal of Power System Engineering
• /
• v.5 no.2
• /
• pp.43-49
• /
• 2001

For machining auto-mobile cam, the developed biarcs-fitting method eliminates the ridge problems in conventional straight-line fitting approximation or single-arc fitting of curve tool path where it leaves ridges of tool marks on the machined surface of the workpiece. The powerful advantage of this biarc method is demonstrated by applying it to the numerically controlled machining of a curved cam profile, also verified by using a CNC simulating program for auto-mobile cam profile. As a result, this algorithm may be used in CNC milling and turning for cam profile machining with short block line.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.6
• /
• pp.111-124
• /
• 2011

The objective of this study is to develop the blind control strategy and method which reduce negative effect of incoming daylight on visual comfort of occupants, minimize psychological anxieties caused by frequent motions of a blind, and maximize positive effect of incoming daylight by opening/closing of a blind. In previous researches on blind controls, major problem is that the time interval and amount of blind movement do not meet the control objective at the inflected zone of solar profile curve. To overcome these limitations revealed in theprevious researches, following tasks were performed in this study. i)To establish the control objective to accomplish the goal of this study. ii)To develop the control methods and algorithms which prevent glare on the work-plane at any time and which control the time interval and amount of blind movement to follow the control objective at various solar profile angle curves. This study proposed the control strategy and method that define the base control section implying the inflection point within the control objective zone and subsequently, divide the control sections for the residual time zones. The proposed strategy and method are found to increase the incoming daylight and solar irradiation by 0 to 15 %.

• Plant Journal
• /
• v.15 no.2
• /
• pp.46-55
• /
• 2019

This paper presents a LNG Liquefaction cycle configuration using two stages of methane expansion (i.e. spliting into two stages as warm & cold to generate an additional inflection point within a cold composite curve) and a single stage of nitrogen expansion to improve the efficiency of the conventional Methane & Nitrogen Expansion Cycle. In comparison with Double Nitrogen Expansion Cycel and Methane & Nitrogen Expansion Cycle, the cycle efficiency has increased approximately from 13.92 and 13.13 to 12.08 kW/ton/day (8~15% efficiency increase). A Life Cycle Cost (LCC) analysis based on Net Present Value (NPV) also show an improvement in therms of project NPV, against a minor increment of a CAPEX.

• Journal of Animal Science and Technology
• /
• v.45 no.4
• /
• pp.509-516
• /
• 2003

Growth curves were estimated for 1083 female Korean cattle raised in Daekwanryeong branch, National Livestock Research Institute (NLRI). Comparisons were made among various growth curve models for goodness of fit for the growth of the cows. Estimated growth curve functions were $W_t=370.2e^{-2.208e^{-0.00327t}$ for Gompertz model, for von Bertalanffy model, and $W_t=341.2(1+5.652e^{-0.00524t})^{-1}$ for Logistic model. Ages at inflection estimated from Gompertz model, von Bertalanffy model and Logistic model were 242.2 days, 191.5 days, and 330.5 days respectively, body weight at inflection were 136kg, 115kg, and 170kg, and daily gain at inflection were 0.445kg, 0.451kg, and 0.446kg. The predicted weights by ages from Gompertz model, von Bertalanffy model, and Logistic model were onsistently overestimated at birth weight and underestimated at 36 month weight. The von Bertalanffy model which had a variable point of inflection fit the data best.

• Journal of Animal Science and Technology
• /
• v.48 no.2
• /
• pp.151-160
• /
• 2006

This study was conducted to investigate the genetic characteristics of growth stages in Hanwoo, to provide useful information in farm management decisions. Data were taken from the nucleus herds of three farms, Namwon, Daegwalyong and Seosan, comprising 27,647 cows, 14,744 bulls, and 1,290 steers in between 1980 and 2004. According to the growth curve by year, the residuals for cows and bulls were 68.49 and 54.29, respectively, under the Gompertz model. The values were lower than in other years. Parameters, A, b and k were estimated as 423.6±5.8, 2.387±0.064 and 0.0908±0.0033 in cows and 823.3±15.3, 3.584±0.070, 0.1139±0.0032 in bulls, respectively. The fitness was higher under the Gompertz model than under the logistic model: monthly and daily estimation for cows were 379.3±7.509, 2.499±0.057, 0.114±0.0045 and 367.1±1.9003, 2.3983±0.012, 0.004±0.00003, respectively. Estimated residual mean squares were 31.85 and 998.4 in their respective models. Monthly and daily estimation of bulls were 834.6±22.00, 3.319±0.062, 0.104±0.0037 and 796.0±6.128, 3.184±0.014, 0.003±0.00003, respectively. Estimated residual mean square were 66.18 and 2106.5. Monthly and daily estimation of steers were 1049.1±144.2, 3.024±0.008, 0.067±0.0096 and 1505.1±176.6, 2.997±0.067, 0.001±0.0001, relatively. Squares, 186.0 and 1119.1. In terms of growth characteristic estimated by Gompertz model, body weight for cows and bulls were 139.53kg and 307.03kg, and the daily gains were 0.52kg and 1.04kg, respectively. Body weight for steers was 385.94kg at the inflection point. Body weight gain was 0.84kg in both models. Our results showed that cows had lower mature weight and daily weight gain, and reached the inflection point earlier than bulls or steers.

• Textile Coloration and Finishing
• /
• v.22 no.3
• /
• pp.187-193
• /
• 2010

The effects of molecular weight (MW) and concentration on the rheological properties of poly(vinyl alcohol) (PVA) solutions in dimethyl sulfoxide (DMSO) were investigated at $30^{\circ}C$. Ubbelohde viscometer and rotational rheometer were employed for dilute and concentrated regime, respectively. In the dilute regime, the Mark-Houwink exponent ($\alpha$) of the solutions determined from three different MWs proved 0.73. The critical concentration (C*), in which the entanglement and overlap of polymer molecules began to take place, decreased with increasing the MW of PVA. Huggins constant ($K_H$) values ranged from 0.33 to 0.45 over the MW examined. In the log-log plot of $\eta_{sp}$ versus [$\eta$]C, the PVA with higher degree of polymerization (DP) gave a greater slope exhibiting the inflection point in the vicinity of C*. In the dynamic viscosity ($\eta'$) curve, the PVA solutions of DP 1700 presented Newtonian fluid behavior over most of the frequency range examined. However, the lower Newtonian flow region reduced with increasing the DP. As the PVA concentration increased, $\eta'$ was increased and the onset shear rate for pseudoplasticity was decreased. In the Cole-Cole plot, PVA solutions showed almost a single master curve in a slope of ca. 1.65 regardless of the DP. However, the increase of the concentration from 8 to 12 wt% for PVA solutions of DP 5000 decreased the slope from 1.73 to 1.57. In the tan $\delta$ curve, the onset frequency for sol-gel transition was shifted from 154 to 92 rad/s with increasing the DP from 3300 to 5000 and from 192 to 46 rad/s with increasing the concentration from 8 to 12 wt%. In addition, longer relaxation time ($\lambda$) was observed with increasing the DP and concentration.