• 한국지반공학회논문집
• /
• 제34권5호
• /
• pp.37-51
• /
• 2018

우리나라의 산지사면은 풍화잔류토 층의 깊이가 얕아 강우의 침투로 인한 사면파괴가 많이 발생한다. 이때 파괴면의 깊이는 얕고 토사층과 기반암의 경계면 근처를 통과하는 특징을 가지고 있다. 강우의 침투로 인한 불포화 토사사면의 불안정성에 중요한 영향을 미치는 지반 정수들은 큰 불확실성을 포함한다. 따라서 본 연구에서는 강우로 인한 사면파괴를 예측하기 위하여 지반의 수리학적 특성과 강도특성을 랜덤변수로 고려하는 몬테카를로 시뮬레이션에 의한 확률론적 해석 절차를 제안하였다. 일정한 강우강도에 대한 기반암이 얕게 존재하는 불포화 토사사면의 안정성 예측을 위하여 강우강도에 따른 사면 표면에서의 경계조건을 반영하여 Green-Ampt 모델을 수정하고 얕은 기반암의 경계조건을 도입하였다. 침투해석의 결과를 무한사면 해석에 적용하여 안전율을 계산하였다. 제안된 확률론적 해석법은 강우의 침투에 따른 사면의 시간 의존적 파괴확률을 계산할 수 있다.

• 한국표면공학회지
• /
• 제50권2호
• /
• pp.98-107
• /
• 2017

Pd-based membranes have been widely used in hydrogen purification and separation due to their high hydrogen diffusivity and infinite selectivity. However, it has been difficult to fabricate thin and dense Pd-based membranes on a porous stainless steel(PSS) support. In case of a conventional PSS support having the large size of surface pores, it was required to use complex surface treatment and thick Pd coating more than $6{\mu}m$ on the PSS was required in order to form pore free surface. In this study, we could fabricate thin and dense Pd membrane with only $3{\mu}m$ Pd layer on a new PSS support manufactured by metal injection molding(MIM). The PSS support had low surface roughness and mean pore size of $5{\mu}m$. Pd membrane were prepared by advanced Pd sputter deposition on the modified PSS support using fine polishing and YSZ vacuum filling surface treatment. At temperature $400^{\circ}C$ and transmembrane pressure difference of 1 bar, hydrogen flux and selectivity of $H_2/N_2$ were $11.22ml\;cm^{-2}min^{-1}$ and infinity, respectively. Comparing with $6{\mu}m$ Pd membrane, $3{\mu}m$ Pd membrane showed 2.5 times higher hydrogen flux which could be due to the decreased Pd layer thickness from $6{\mu}m$ to $3{\mu}m$ and an increased porosity. It was also found that pressure exponent was changed from 0.5 on $6{\mu}m$ Pd membrane to 0.8 on $3{\mu}m$ Pd membrane.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.458-458
• /
• 2010

The process window for the etch selectivity of silicon nitride ($Si_3N_4$) layers to extreme ultra-violet (EUV) resist and variation of line edge roughness (LER) of EUV resist were investigated durin getching of $Si_3N_4$/EUV resist structure in a dual-frequency superimposed capacitive coupled plasma (DFS-CCP) etcher by varying the process parameters, such as the $CH_2F_2$ and $N_2$ gas flow rate in $CH_2F_2/N_2$/Ar plasma. The $CH_2F_2$ and $N_2$ flow rate was found to play a critical role in determining the process window for infinite etch selectivity of $Si_3N_4$/EUV resist, due to disproportionate changes in the degree of polymerization on $Si_3N_4$ and EUV resist surfaces. The preferential chemical reaction between hydrogen and carbon in the hydrofluorocarbon ($CH_xF_y$) polymer layer and the nitrogen and oxygen on the $Si_3N_4$, presumably leading to the formation of HCN, CO, and $CO_2$ etch by-products, results in a smaller steady-state hydrofluorocarbon thickness on $Si_3N_4$ and, in turn, in continuous $Si_3N_4$ etching due to enhanced $SiF_4$ formation, while the $CH_xF_y$ layer is deposited on the EUV resist surface. Also critical dimension (and line edge roughness) tend to decrease with increasing $N_2$ flow rate due to decreased degree of polymerization.

• 대한기계학회논문집A
• /
• 제22권4호
• /
• pp.779-789
• /
• 1998

In this paper, the thermal shock responses of collinear cracks in a layered medium are investigated based on the uncoupled, quasi-static plane thermoelasticity. The medium is modeled as a bonded structure composed of a surface layer and a semi-infinite substrate. Between these two dissimilar homogeneous constituents, a functionally graded interfacial zone exists with the nonhomogeneous features of continuously varying thermoelastic properties. Three cracks are assumed to be present in the layered medium, one in each one of the constituent materials, aligned collinearly normal to the nominal interfaces. A system of singular integral equations is solved, subjected to the forcing terms of equivalent transient thermal tractions acting on the locations of cracks via superposition. Main results presented are the transient thermal stress intensity factors to illustrate the parametric effects of various geometric and amterial combinations of the medium with the thermoelastically graded interfacial zone and the collinear cracks.

• 펄프종이기술
• /
• 제32권2호
• /
• pp.26-34
• /
• 2000

Understanding the nip geometry and heat transfer phenomena of soft nip calenders, which has been used in the production of newsprint and coated papers for many years, is very important since improper setting of soft nip calendering conditions causes deterioration of paper quality and productivity. In this study theoretical analysis on nip pressure and heat transfer phenomena in the nip of soft nip calenders has been made. The variables examined were calendering pressure, surface temperature of the heating roll, nip residence time and ingoing sheet moisture, By measuring nip widths and maximum nip pressure with Prescale film at a normal temperature, accurate line load has been obtained. With this line load, nip pressures at different temperature and nip widths were calculated. Results showed that as temperature increased, nip widths increased and nip pressures decreased. Equations derived for the heat conduction phenomena in soft nip calender nip were derived based on the semi-infinite plate and finite difference method and were used for the analysis of heat transfer within the nip. Temperature profiles in z-direction of paper within the nip were obtained. Finite difference method allowed more accurate analysis of the heat transfer in the calender nip. In this study newsprint and coated paper were considered as a single plate and two-layer plate consisted of sheet and coating layers, respectively. Heat trans-fer to paper increased as heated roll surface temperature and nip residence time were increased.

• Wind and Structures
• /
• 제26권5호
• /
• pp.317-329
• /
• 2018

Wake characteristics of the flow over a finite square prism at different incidence angles were experimentally investigated using an open-loop wind tunnel. A finite square prism with a width D = 15 mm and a height H = 7D was vertically mounted on a horizontal flat plate. The Reynolds number was varied from $6.5{\times}10^3$ to $28.5{\times}10^3$ and the incidence angle ${\alpha}$ was changed from $0^{\circ}$ to $45^{\circ}$. The ratio of boundary layer thickness to the prism height was about ${\delta}/H=7%$. The time-averaged velocity, turbulence intensity and the vortex shedding frequency were obtained through a single-component hotwire probe. Power spectrum of the streamwise velocity fluctuations revealed that the tip and base vortices shed at the same frequency as that ofspanwise vortices. Furthermore, the results showed that the critical incidence angle corresponding to the maximum Strouhal number and minimum wake width occurs at ${\alpha}_{cr}=15^{\circ}$ which is equal to that reported for an infinite prism. There is a reduction in the size of the wake region along the height of the prism when moving away from the ground plane towards the free end.

• 한국통신학회논문지
• /
• 제27권8C호
• /
• pp.729-740
• /
• 2002

본 논문에서는 광 인터넷 망의 가상망 재구성을 위하여 최적의 망 재구성 정책을 고려한 보상-비용 함수를 최대화하는 다단계 결정 문제로 정의 하였다. 그리고 트래픽 요구사항을 만족하기 위해서 노드 교환 기법에 근거한 새로운 휴리스틱 알고리즘을 제안하였다. 또한 트래픽 예측 기법을 사용하여 휴리스틱 알고리즘에 의해 발생하는 근사 문제를 해결 하고, 이를 바탕으로 트래픽 예측 다단계 재구성 정책을 제안하였다. 실험결과 다단계 재구성 정책은 물리적 자원이 제한된 환경에서 기존의 방법에 비해 뛰어난 성능을 보였다.

• 대한기계학회논문집
• /
• 제16권4호
• /
• pp.775-786
• /
• 1992

본 연구에서는 DVM의 이론적 배경과 수치계산에 대해 자세히 다루었다. 음향 교란이 가졌을 때의 재부착에 대한 수치해석결과는 Kiya등의 실험결과와 비교하 였으며 만족할만한 일치를 보여주었다. 결과 및 고찰에서는 주로 음향교란이 있는 경우의 재부착길이를 최소화하는 주파수와 교란이 없는 유동의 난류구조해석을 평균속 도 및 압력과 그의 섭동치, 그리고 파워 스펙트럼과 상관계수등을 통해 자세히 비교검 토하였다.

• 대한기계학회논문집A
• /
• 제24권7호
• /
• pp.1740-1747
• /
• 2000

Under repeated rolling, initial plastic deformation introduces residual stresses which render the steady cyclic state purely elastic. This is called the process of shakedown. Many studies have been done about the shakedown in semi-infinite half space using calculated Hertizian pressure. In this paper shakedown processes in a shaft are studied by finite element analyses of a two dimensional(plane strain) model with elastic-linear-kinematic-hardening-plastic material subjected to repeated, frictionless rolling contact. Symmetric and non-symmetric pressure distributions are obtained using a simplified model of the bearing-shaft assembly. The rolling contact is simulated by repeatedly translating both pressure distributions along the surface of the shaft. By the influence of the non-symmetric pressure, larger residual radial tensile stress is generated in the immediate subsurface layer, which may make a crack propagate and, the subsurface undergoes a zigzag plastic deformation during the shakedown process, which may lead to a crack initiation.

• Structural Engineering and Mechanics
• /
• 제74권1호
• /
• pp.91-104
• /
• 2020

A mathematical analysis has been carried out for understanding the traversal attributes of torsional waves in a Voigt-type viscoelastic porous layer bounded with corrugated surfaces resting over a heterogeneous transversely isotropic gravitating semi-infinite medium. Both the media are assumed to be under the effect of initial stresses acting along horizontal directions. In the presumed geometry, continuous and periodic type of corrugation has been considered. The condensed form of dispersion relation has been obtained analytically with the aid of the Whittaker's function and suitable boundary conditions. The influence of viscoelasticity, porosity, initial stresses, heterogeneity, gravity, undulation and position parameters on the phase and damped velocities has been illustrated graphically. In addition, relative examination investigating the impact of corrugated and planar bounded surfaces on the dispersion and damping characteristics is one of the important highlights of this study.