• Structural Engineering and Mechanics
• /
• 제4권2호
• /
• pp.139-148
• /
• 1996

Vector algorithms and the relative importance of the four basic modules (computation of element stiffness matrices, assembly of the global stiffness matrix, solution of the system of linear simultaneous equations, and calculation of stresses and strains) of a finite element computer program for inelastic analysis of reinforced concrete shells are presented. Performance of the vector program is compared with a scalar program. For a cooling tower problem, the speedup factor from the scalar to the vector program is 34 for the element stiffness matrices calculation, 25.3 for the assembly of global stiffness matrix, 27.5 for the equation solver, and 37.8 for stresses, strains and nodal forces computations on a Gray Y-MP. The overall speedup factor is 30.9. When the equation solver alone is vectorized, which is computationally the most intensive part of a finite element program, a speedup factor of only 1.9 is achieved. When the rest of the program is also vectorized, a large additional speedup factor of 15.9 is attained. Therefore, it is very important that all the modules in a nonlinear program are vectorized to gain the full potential of the supercomputers. The vector finite element computer program for inelastic analysis of RC shells with layered elements developed in the present study enabled us to perform mesh convergence studies. The vector program can be used for studying the ultimate behavior of RC shells and used as a design tool.

• Earthquakes and Structures
• /
• 제5권2호
• /
• pp.239-259
• /
• 2013

Typically, beams that form part of structural systems are subjected to vertical distributed loading along their length. Distributed loading affects moment and shear distribution, and consequently spread of inelasticity, along the beam length. However, the finite element models developed so far for seismic analysis of frame structures either ignore the effect of vertical distributed loading on spread of inelasticity or consider it in an approximate manner. In this paper, a beam-type finite element is developed, which is capable of considering accurately the effect of uniform distributed loading on spreading of inelastic deformations along the beam length. The proposed model consists of two gradual spread inelasticity sub-elements accounting explicitly for inelastic flexural and shear response. Following this approach, the effect of distributed loading on spreading of inelastic flexural and shear deformations is properly taken into account. The finite element is implemented in the seismic analysis of plane frame structures with beam members controlled either by flexure or shear. It is shown that to obtain accurate results the influence of distributed beam loading on spreading of inelastic deformations should be taken into account in the inelastic seismic analysis of frame structures.

• 전산구조공학
• /
• 제5권1호
• /
• pp.83-89
• /
• 1992

사용하중하의 철근콘크리트 스래브의 비탄성 처짐을 산정하는 실용적인 방법을 제시하였다. 선형 유한요소 해석의 탄성해석결과와 설계된 철근량을 이용하여 비탄성 처짐계수(.betha.)를 결정하고, 이를 이용하여 설계된 슬리브의 사용성을 검토하기 위한 사용하중하의 처짐을 구할 수 있도록 하였다. 모서리에 지지된 슬래브 예에서 제시한 방법으로 구한 비탄성처짐과 실험 및 비선형해석 결과와 비교해 본 결과 서로 매우 잘 일치함을 보여주었다. 제시된 방법을 비정형 슬래브 설계에 응용한 문제도 고려하였다.

• 한국지진공학회논문집
• /
• 제9권5호
• /
• pp.63-74
• /
• 2005

이 연구의 목적은 비탄성 유한요소해석을 이용하여 철근콘크리트 교각의 내진성능을 평가하는데 있다. 정확하고 올바른 성능평가를 위하여 신뢰성 있는 비선형 유한요소해석 프로그램을 사용하였다. 사용된 프로그램은 철근콘크리트 구조물의 해석을 위한 RCAHEST이다. 손상지수는 지진하중하의 철근콘크리트 교각의 손상을 수치적으로 정량화하는 방법으로서 제안되었다. 이 연구에서는 철근콘크리트 교각의 내진성능평가를 위해 제안한 해석기법을 신뢰성 있는 연구자의 실험결과와 비교하여 그 타당성을 검증하였다.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2006년도 학술발표회 논문집
• /
• pp.292-299
• /
• 2006

The purpose of this study is to investigate the inelastic behavior of precast segmental prestressed concrete bridge columns. A computer program, named RCAHEST (Reinforced Concrete Analysis in Higher Evaluation System Technology), for the analysis of reinforced concrete structures was used. Material nonlinearity is taken into account by comprising tensile, compressive and shear models of cracked concrete and a model of reinforcing steel. An unbonded tendon element based on the finite element method, that can represent the interaction between tendon and concrete of prestressed concrete member, is used. A joint element is newly developed to predict the inelastic behaviors of segmental joints. The proposed numerical method for the inelastic behavior of precast segmental prestressed concrete bridge columns is verified by comparison with reliable experimental results.

• 대한토목학회논문집
• /
• 제32권6A호
• /
• pp.399-409
• /
• 2012

비세장 복부판을 갖고 균일모멘트를 받는 HSB 강재가 적용된 플레이트거더의 비탄성 횡비틀림좌굴 영역 휨강도 특성을 비선형 유한요소해석으로 분석하였다. HSB600 및 HSB800 강재로 제작된 균질단면 강거더와 HSB800 강재와 SM570-TMC 강재를 함께 적용한 하이브리드단면 거더를 고려하였으며, 일반강재와의 상대 비교를 위하여 SM490-TMC 강거더에 대한 해석도 수행하였다. 해석대상 비합성 I-거더 단면의 플랜지와 복부판을 쉘요소로 모델링하고 ABAQUS 프로그램을 이용하여 재료 및 기하학적 비선형 유한요소해석을 수행하였다. 강재는 탄소성-변형경화 재료로 모델링하였고 초기변형과 단면의 잔류응력을 고려하였으며, 이들이 비탄성 횡비틀림좌굴 영역에서 휨거동에 미치는 영향을 분석하였다. HSB 고강도강을 적용한 플레이트거더의 FE 해석과 한계상태법 도로교설계기준, AASHTO LRFD, Eurocode 등 국내외 주요 설계기준에 의한 공칭휨강도와 비교하고 이들 설계기준을 평가하였다.

• 대한기계학회논문집A
• /
• 제21권7호
• /
• pp.1042-1049
• /
• 1997

LMFBR(Liquid Metal Fast Breeder Reactor) vessel is operated under the high temperatures of 500-550.deg. C. Thus, transient thermal loads were severe enough to cause inelastic deformation due to creep-fatigue and plasticity. For reduction of such inelastic deformations, Y-piece structure in the form of a thermal sleeve is used in LMFBR vessel under repeated start-up, service and shut-down conditions. Therefore, a systematic method for inelastic analysis is needed for design of the Y-piece structure subjected to such loading conditions. In the present investigation, finite element analysis of heat transfer and inelastic thermal stress were carried out for the Y-piece structure in LMFBR vessel under service conditions. For such analysis, ABAQUS program was employed based on the elasto-plastic and Chaboche viscoplastic constitutive equations. Based on numerical data obtained from the analysis, creep-fatigue damage estimation according to ASME Code Case N-47 was made and compared to each other. Finally, it was found out that the numerical predictio of damage level due to creep based on Chaboche unified viscoplastic constitutive equation was relatively better compared to elasto-plastic constitutive formulation.

• Computers and Concrete
• /
• 제20권3호
• /
• pp.351-360
• /
• 2017

This paper presents an efficient membrane finite element for the cyclic inelastic response analysis of RC structures under complex plane stress states including shear. The model strikes a balance between accuracy and numerical efficiency to meet the challenge of shear wall simulations in earthquake engineering practice. The concrete material model at the integration points of the finite element is based on damage plasticity with two damage parameters. All reinforcing bars with the same orientation are represented by an embedded orthotropic steel layer based on uniaxial stress-strain relation, so that the dowel and bond-slip effect of the reinforcing steel are presently neglected in the interest of computational efficiency. The model is validated with significant experimental results of the cyclic response of RC panels with uniform stress states.

• 대한기계학회논문집
• /
• 제18권4호
• /
• pp.1009-1018
• /
• 1994

An attempt is made to develop a kind of hybrid numerical method for computations of the thermal stresses during a solidification process. In this algorithm, the phase-change heat transfer analysis is perrformed by a finite volume method(FVM) and the thermal stress analysis in a solidifying body by a finite element method(FEM). The temperatures at the grid points calculated in the heat transfer analysis are transferred to those of gauss points in elements by a bi-cubic surface patch technique for the thermal stress analysis. A hyperbolic-sine constitutive law is used to prescribe the inelastic strain rate of material. Results for the unidirectional solidification process of a pure aluminum are compared with those of others and shows good agreement.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1992년도 춘계학술대회 논문집 92
• /
• pp.115-130
• /
• 1992

The analysis of thermoplastic automotive bumpers needs not only characterizations of the thermomechanical properties of thermoplastic materials but also the finite element method which can solve the problems with a large deflection, an elastic-inelastic deformation, and a change of a contact state. This paper describes the modeling techniques in the finite element analysis in order to get a good prediction of thermoplastic bumper behaviors. Simplification effects of a complex geometry of thermoplastic bumpers are studied by comparing the results from static loading tests and the finite element analysis.