• Journal of Korean Tunnelling and Underground Space Association
• /
• v.24 no.4
• /
• pp.305-316
• /
• 2022

Hydrogen energy is emerging as an alternative to the depletion of fossil fuels and environmental problems, and the use of hydrogen vehicles is increasing in the automobile industry as well. However, since hydrogen has a wide flammability limit of 4 to 75%, there is a high concern about safety in case of a hydrogen car accident. In particular, in semi-enclosed spaces such as tunnels and underground parking lots, a fire or explosion accompanied by hydrogen leakage is highly likely to cause a major accident. Therefore, it is necessary to review hydrogen safety through analysis of flammability areas caused by hydrogen leakage. Therefore, in this study, the effect of the air velocity in the tunnel on the flammability area was investigated by analyzing the hydrogen concentration according to the hydrogen leakage conditions of hydrogen vehicles and the air velocity in the tunnel in a road tunnel with standard section. Hydrogen leakage conditions were set as one tank leaking and three tanks leaking through the TPRD at the same time and a condition in which a large crack occurred and leaked. And the air velocity in the tunnel were considered 0, 1, 2.5, and 4.0 m/s. As a result of the analysis of the flammability area, it is shown that when the air velocity of 1 m/s or more exists, it is reduced by up to 25% compared to the case of air velocity of 0 m/s. But there is little effect of reducing the flammability area according to the increase of the wind speed. In particular, when a large crack occurs and completely leaks in about 2.5 seconds, the flammability area slightly increases as the air velocity increases. It was found that in the case of downward ejection, hydrogen gas remains under the vehicle for a considerably long time.

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.4
• /
• pp.359-370
• /
• 2022

Despite continuous efforts to reduce on-site safety accidents, the construction industry remains a high-risk sector with a high rate of fatal accidents. Design for Safety(DFS), which manages safety risk factors at the design stage, is being used as a method to lower the construction safety accident rate. However, due to limited knowledge, designers are unaware of the design-results risks during the different of the project lifecycle, including construction, operation, and maintenance. Effective DFS can be conducted if the designer understands the effect of the building shape on the safety accident rate and corresponding safety management cost(SMC). The cost of safety facilities such as fall prevention nets and safety fences will vary depending on the shape of the building. This study analyzes the outer perimeter length's impact on SMC. Following the data collection from 21 projects for this study, an analysis was conducted using the independent variables of the building perimeter(BP), building shape factor(BSF), and building area(BA), the dependent variable of SMC. The correlation R2 was found to be 0.876, 0.801 and 0.792 between the BP and SMC, BSF and SMC, BA and SMC, respectively, indicating that these factors were closely related.

• Journal of the Society of Disaster Information
• /
• v.18 no.4
• /
• pp.828-838
• /
• 2022

Purpose: Through the establishment of a computerized system of risk assessment, the purpose is to analyze the case of whether the co-workers who are subject to the risk assessment at the construction site can easily fill it out and expect disaster reduction through efficient risk assessment activities. Method: By providing the risk factors and safety measures for the work by selecting the type of work, the risk estimation and the establishment of countermeasures can be made, and a system has been established to enable practical disaster prevention activities by presenting disaster cases for the work. Result: Through the analysis of the change in the scaled disaster rate for the years following the on-site application after the establishment of the risk assessment computer system of H Construction Company, it was confirmed that the scaled disaster rate of the domestic construction industry increased, while the conversion disaster rate of H Construction Company decreased. Conclusion: Through the computational systemization of risk assessments, workers in the field can easily access the risk assessment, evaluate the risk factors of the process and establish risk prevention measures, and it has been analyzed that there is an impact on the reduction of the disaster rate during the operational analysis period.

• Industry Promotion Research
• /
• v.9 no.2
• /
• pp.37-44
• /
• 2024

This study selected the worst-case scenario for fireball and vapor cloud explosion (VCE) of a styrene monomer storage tank installed in a petrochemical production plant and performed damage prediction and accident impact analysis. The range of influence of radiant heat and overpressure due to fireball and vapor VCE during the abnormal polymerization reaction of styrene monomer, the main component of the mixed residue oil storage tank, was quantitatively analyzed by applying the e-CA accident damage prediction program. The damage impact areas of radiant heat and explosion overpressure are analyzed to have a maximum radius of 1,150m and 626m, respectively. People within 1,150m of radiant heat of 4kW/m2 may have their skin swell when exposed to it for 20 seconds. In buildings within 626m, where an explosion overpressure of 21kPa is applied, steel structures may be damaged and separated from the foundation, and people may suffer physical injuries. In the event of a fire, explosion or leak, determine the risk standards such as the degree of risk and acceptability to workers in the work place, nearby residents, or surrounding facilities due to radiant heat or overpressure, identify the hazards and risks of the materials handled, and establish an emergency response system. It is expected that it will be helpful in establishing measures to minimize damage to workplaces through improvement and investment activities.

• Journal of the Society of Disaster Information
• /
• v.20 no.1
• /
• pp.106-116
• /
• 2024

Purpose: This paper conducts IoT and CCTV-based safety monitoring to analyze accidents and potential risks occurring at construction sites, and detect and analyze risks such as falls and collisions or abnormalities and to establish a system for early warning using devices like a walkie-talkie and chatbot service. Method: A safety management service model is presented through smart construction technology case studies at the construction site and review a relevant literature analysis. Result: According to 'Construction Accident Statistics,' in 2021, there were 26,888 casualties in the construction industry, accounting for 26.3% of all reported accidents. Fatalities in construction-related accidents amounted to 417 individuals, representing 50.5% of all industrial accident-related deaths. This study suggests implementing AI chatbot services for construction site safety management utilizing IoT-based health monitoring technologies in smart construction practices. Construction sites where stakeholders such as workers participate were demonstrated by implementing an artificial intelligence chatbot system by selecting major risk areas within the workplace, such as scaffolding processes, openings, and access to hazardous machinery. Conclusion: The possibility of commercialization was confirmed by receiving more than 90 points in the satisfaction survey of participating workers regarding the empirical results of the artificial intelligence chatbot service at construction sites.

• Journal of the Korea Convergence Society
• /
• v.11 no.6
• /
• pp.173-182
• /
• 2020

Since 2000, Korea has seen a big trend in the market, as the EU tightened regulations on environment due to global warming, high oil prices and aging rural population distribution, strengthening the need for multi-purpose electric moto vehicles for small farmers based on eco-friendly energy. Multi-purpose electric motor vehicles for rural small businesses will be a very innovative means of transportation, not only maintained at a low cost and to reduce greenhouse gases through the activation of eco-friendly energy, but also be a very innovative means of transportation for reducing the labor intensity of the aging farming industry and transporting night work and logistics. In this paper, with the implementation of eco-friendly energy policies, small and medium-sized rural small business owners can easily operate on unpaved roads and well-drawn farming environments, while the intensity of labor can be reduced when transporting crops also can simply replace parts at a low cost in the event of an accident. To propose rural multi-purpose modular electric vehicles, the existing literature is reviewed and 12 modular parts are presented by benchmarking electric vehicles at home and abroad. This paper is thought to be helpful for the research of the industry as well as the design industry of modular electric vehicles.

• Journal of the Korea Convergence Society
• /
• v.9 no.7
• /
• pp.231-240
• /
• 2018

Automobile industry is facing a variety of risks, including the rise of international oil price and the increase of car prices. In addition to the government's deregulation, efforts should be made to improve management aiming at higher production efficiency. In this study, we established a model for evaluating the procurement logistics based on the Fuzzy-AHP-TOPSIS by using the factors that are actually used in real companies aimed at the improvement of procurement logistics. A total of three automobile factories of Company G were chosen as the evaluation subject. In the result of the Fuzzy-AHP analysis that was conducted on a sample of three car factories, solving the long-term quality problems, minimizing the stop time due to the shortage of materials, preventing the of equipment accident, and solving the short-term quality problems were proven to be the most important factors. TOPSIS analysis result indicated that Factory B had the best procurement logistics. Our study has significance that it can contribute to the improvement of efficiency in the automobile industry as the evaluation model suggested in this study can be used for regular evaluation related to the procurement logistics in the future.

• Journal of Radiation Protection and Research
• /
• v.46 no.1
• /
• pp.14-23
• /
• 2021

Background: For radiological protection and control, the International Commission on Radiological Protection (ICRP) provides the nominal risk coefficients related to radiation exposure, which can be extrapolated using the excess relative risk and excess absolute risk obtained from the Life Span Study of atomic bomb survivors in Hiroshima and Nagasaki with the dose and dose-rate effectiveness factor (DDREF). Materials and Methods: Since it is impossible to directly estimate the radiation risk at doses less than approximately 100 mSv only from epidemiological knowledge and data, support from radiation biology is absolutely imperative, and thus, several national and international bodies have advocated the importance of bridging knowledge between biology and epidemiology. Because of the accident at the Tokyo Electric Power Company (TEPCO)'s Fukushima Daiichi Nuclear Power Station in 2011, the exposure of the public to radiation has become a major concern and it was considered that the estimation of radiation risk should be more realistic to cope with the prevailing radiation exposure situation. Results and Discussion: To discuss the issues from wide aspects related to radiological protection, and to realize bridging knowledge between biology and epidemiology, we have established a research group to develop low-dose and low-dose-rate radiation risk estimation methodology, with the permission of the Japan Health Physics Society. Conclusion: The aim of the research group was to clarify the current situation and issues related to the risk estimation of low-dose and low-dose-rate radiation exposure from the viewpoints of different research fields, such as epidemiology, biology, modeling, and dosimetry, to identify a future strategy and roadmap to elucidate a more realistic estimation of risk against low-dose and low-dose-rate radiation exposure.

• Journal of Environmental Health Sciences
• /
• v.17 no.2
• /
• pp.78-94
• /
• 1991

The purpose of this study is to research the actual conditions of industrial accident patients and to produce worker satisfaction and a rational and effective counter measure pain. Direct interviews with 179 cases (in and out patients) were carried out during a three month period from April to July 1990, at six hospitals two general hospitals Sun Lin and Sung Mo in Po Hang, and four general hospitals in Taegu Kyung Pook University Hospital, Dong San Medical Center, Young Nam Medical Center and Catholic Hospital. The results of this study are summarized as follows: 1. Among the 179 cases, 51.6 % were male and 48.4 % were female. The two largest age groups were 30~39, 31.8 % and 20~29, 27.4 %. Among the 179 cases, 51.6% were married, the largest family number was 2 to 3, 41.1% and 4 to 5, 25.6%. Educationally, graduation from high school was the largest group, 46.4% among the patients, followed by middle school and primary school. The largest group income level was from 40~69만원, 45.2%. The largest group of patients who worked over 50 hrs. a week was 52.0%. The largest group of patients who worked less than 1 year was 44.7%, of the patients in work places of less than 100 people, 60.3% were injured and in work places of 100~299 people, 20.1% were injured. In manufacturing, the lagest group injured was 55.3%, the next group was transport, stroage, communication. The largest group of production workers injured was 40.2%. 2. The cause of injury in the largest group was facility problems, 33.5%. The next group was unsafe habits, 30.2% a lack of safety knowledge, 17.9% and insufficient supervision, 12.3%. The 30~39 year age group was head the highest number of injuries, 40.4% work places with more than 10 yeras of work, 44.4% work palces with more than 1000 people, 56.3% and mining accidents, 80.0%. Among these groups the highest cause of injury was due to facility problems. 3. The accident pattern showed machinery injuries 28.5% as the largest group, followed by falls & falling objects 17.3%, fire & electric 15.1%, struke by an object 14.5%, followed by overaction and vehicular accidents. The accident pattern showed 46.4 % among workers over the 50 year age group, workers in the 5~10 year group, 50.0 % places employing more than 1000 workers, 35.3 % : construction 73.7%, and construction workers 57.1%, among these fall & falling objects caused the greatest number of injuries. 4. The largest group of injuries was fractures 54.8%, trauma 14.5%, amputation 11.7%, open wound, and burns. The largest number of fractures occurred in people in the 30~39 year age group, 63.2 % over 10 years of work, 55.6% in work places of 300~400 people, 63.6% construction 63.2% and general workers 57.2 %. 5. The largest group of injuries was upper extremity 45.3%, lower extremity 24.0%, trunk 18.5 % and head or neck 12.2%. Of these groups, upper extremity injuries were the highest in those less 20 years old 75.0%, less than 1 years of work 59.5%, in work places of 500~999 people 60.0%, manufacturing 56.6 % and production workers 55.6%. 6. Periods of injury showed 34 people injured in September, to be the largest followed by October, 32 August, 22 people July, 19 people and the lowest December, 2 people. During the week, Friday had the largest group injured, 35 people followed by Saturday, 26 people and the lowest was Wednesday, 17 people, During the day 1400 hours had the largest group injured, 38 people followed by 800 hours, 31 people. 7. On a basis of 5 as the highest mark, the average, according to worker satisfaction showed facility safety 3.55, work environment 3.47, income 3.44, job 3.21 and treatment 2.98. 8. The correlation between general characteristics and injury showed that age was directly correlated to the duration of work(r=.2591) p<0.01, age was directly correlated to industry (r=2311) p<0.01, and the duration was directly correlated to occupation(r =.4372) p<0.001.

• The Journal of Korean Physical Therapy
• /
• v.3 no.1
• /
• pp.151-174
• /
• 1991

The purpose of this study is to research the actual conditions of industrial accident patients and to produce worker satisfaction and a rational and effective counter measure plan. Direct interviews with 179 cases (in and out patients) were carried out during a three month period from April to July 1990, at six hospitals : two general hospitals Sun Lin and Sung Mo in Po Hang, and four general hospitals in Taegu : Kyung pooh University Hospital, Dong San Medical Center, Young Nam Medical Center and Catholic Hospital. The results of this study are summarized as fellows : 1. Among the 179 cases, $51.6\%$ were male and $48.4\%$ were female. The two largest age groups were 30-39, $31.8\%$ and 20-29, $27.4\%$. Among the 179 cases, $51.6\%$ were married, the largest family number was 2 to 3, $41.1\%$ and 4 to 5, $25.6\%$. Educationally, graduation from high school was the largest group, $46.4\%$ among ,the patients, followed by middle school and primary school. The largest group income level was from 40-69 만원, $45.2\%$. The largest group of patients who worked over 50 hrs. a week was $52.0\%$. The largest group of patients who worked less than 1 year was $44.7\%$, of the patients in work places of less than 100 people, $60.3\%$ were injured and in work places of 100-299 people, $20.1\%$ were injured. In manufacturing, the largest group injured was $55.3\%$, the next group was transport, storage, communication. The largest group of production workers injured was $40.2\%$. 2. The cause of injury in the largest group was facility problems, $33.5\%$. The next group was unsafe habits, $30.2\%$ ; a lack of safety knowledge, $17.9\%$ ; and insufficient supervision, $12.3\%$. The 30-39 year age group head the highest number of injuries, $40.4\%$ ; work places with more than 10 years of work, $44.4\%$ ; work places with more than 1000 people, $56.3\%$ and mining accidents, $80.0\%$. Among. these groups the highest cause of injury was due to facility problems. 3. The accident pattern showed machinery injuries $28.5\%$ as the largest group, followed by falls & falling objects $17.3\%$, fire & electric $15.1\%$, strucke by an object $14.5\%$, followed by overaction and vehicular accidents. The accident pattern showed $46.4\%$ among workers over the 50 year age group, workers in the 5-10 year group, $50.0\%$ ; places employing more than 1000 workers, $35.3\%$ ; construction $73.7\%$, and construction workers $57.1\%$, among these fall & falling objects caused the greatest number of injuries. 4. The largest group of injuries was fractures $54.8\%$, trauma $14.5\%$, amputation $11.7\%$, open wound, and burns. The largest number of fractures occurred in people in the 30-39 year age group, $63.2\%$ : over 10 years of work, $55.0\%$ ; in work places of 300-490 people, $63.6\%$ ; construction $63.2\%$ and general workers $57.2\%$. 5. The largest group of injuries was upper extremity $45.3\%$, lower extremity $24.0\%$, trunk $18.5\%$ and head or neck $12.2\%$. Of these groups, upper extremity injuries were the highest in those less than 20 years old $75.0\%$, less than 1 year or work $59.5\%$, in work places of 500-999 people $60.0\%$, manufacturing $56.6\%$ and production workers $55.6\%$. 6. Periods of injury showed 34 people injured in September, to be the largest followed by October, 32 ; August, 22 people : July, 19 people and the lowest December, 2 people. During the week, Friday had the largest group injured, 35 people ; followed by Saturday, 26 people and the lowest was Wednesday, 17 people, During the day 1400 hours had the largest group injured, 38 people ; followed by 800 hours, 31 people. 7. On a basis of 5 as the highest mark, the average, according to worker satisfaction showed facility safety 3.55, work environment 3.47, income 3.44, job 3.21 and treatment 2.98. 8. The correlation between general characteristics and injury showed that age was directly correlated to the duration of work (r=2591) p<0.01, age was directly correlated to industry (r=2311) p<0.01, and the duration was directly correlated to occupation (r=4372) p<0.001.