• Proceedings of the KIEE Conference
• /
• 2005.07d
• /
• pp.2658-2660
• /
• 2005

This paper presents a stator winding fault diagnosis technique of induction motor on the PC - based virtual instrumentation system designed using the graphical programming language LabVIEW. This method collects the 3-phase current signals using the current probe amplifier and PXI/DAQ system then the preprocessing removes the noise using LPF, after then this method transforms the stator current to Park's vector and obtains the each Park's Vector pattern and detects stator winding fault by comparing the obtained faulted pattern with the healthy pattern. This proposed LabVIEW based diagnosis system is applied to the 3 phase 1 hp induction motor and obtained the reasonable results under no load condition. The test results give us the possibility a simple and realistic on-line winding fault diagnosis system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.2
• /
• pp.294-299
• /
• 2002

This paper presents a faults diagnosis technique of induction motors based on a neural network. Only stator current is measured, transformed by using FFT and normalized for the training. Healthy, bearing fault, stator fault and rotor end-ring fault motors are prepared to obtain the learning data and diagnose the several faults. For more effective diagnosis, the load rate is changed by 100%, 60%, 30% of full load and the obtained are applied to the teaming process. The experimental results show the proposed method is very detectable and applicable to the real diagnosis system.

• 전기의세계
• /
• v.30 no.11
• /
• pp.734-746
• /
• 1981

This paper suggests on-load torque measurement for 3 phase induction motors by input -voltage and current utilizing symmetric coordinate analysis technique on the basis of the induction motor equivalent circuit. In this paper, two cases are treated with, i.e, one is the case where the motors' exciting current and primary leakage impedance voltage drop are compensated automatically, adopting the ideal wattmeter whose current coil impedance and voltage coil impedance are 0 and .inf. respectively, and the other is the case where non-ideal wattmeter is adopted and the compensation above is made by computation. As a result of the case study, following conclusions are obtained. 1) By proper combination of the error propagation law and the limit of power consumption, the desirable overall measurement error of the apparatus can be obtained on the basis of the inherent errors of CT and PT. 2) The measurement error is larger in current simulation circuit than in voltage simulation circuit. 3) Between the two cases, the latter is more advantageous than the former from the viewpoint of feasibility and the measurement error. 4) As the attachment of Ammeter in the current simulation circuit influences the measurement error considerably, its internal impedance should be large considerably. 5) The larger the consumption power of the apparatus is, the easier the feasibility is.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.41 no.3
• /
• pp.1-8
• /
• 2004

This paper proposes an LQ-PID controller to reduce errors occurring between input and output speeds in braking or emergency braking and to solve delay of speed or the excessive overshoot problems occurring at the speed control of induction motor. The conventional LQ controller is a method that move the poles in locations that satisfy design specifications such as overshoot and settling time etc. by state-feedback. So it may not be able to satisfy the overshoot requirement in case of the existence of zero in the closed loop transfer function. To attack this zero-problem it is presented a new design methodology of LQ-PID controller by introducing an analytic technique to eliminate the effect of zeros on the closed loop transfer function.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.4
• /
• pp.21-27
• /
• 2015

Induction bending is a method that allows the bending of any material that conducts electricity. This technology applies a bending force to a material that has been locally heated by an eddy current induced by a fluctuating electromagnetic field. Induction bending uses an inductor to locally heat steel through induction. This results in a narrow heat band in the shape to be bent. In general, the reduction of thickness attenuation of a large-diameter steel pipe is not allowed to exceed 12.5%. In this paper, in order to meet the standard of thickness attenuation reduction, a non-uniform heating temperature jump-bending process was investigated. As a result, the developed bending technique meets the requirements of thickness attenuation reduction for large-diameter steel pipes.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.4
• /
• pp.79-84
• /
• 2020

Induction bending via high-frequency heating is widely used for manufacturing pipe and section steel bends. It allows productivity improvement, unit cost reduction, delivery time compliance, and good mechanical properties. The recent increase in high-end vessels and offshore plants has raised the demand for high-frequency bending, which should improve the product quality and reduce the costs by simplifying the fabrication process; therefore, the characteristics and performance of this technique must be studied and proper design technology is required. During hot pipe bending via induction heating, the outward wall thickness of the pipe is thinned due to tensile stress and this thickness reduction cannot exceed 12.5%. This study focused on pipe bends with a bending curvature of 5D and their optimization design; in particular, the conditions that can both improve the productivity of the high-frequency bending process and keep the maximum thickness reduction below 12.5% were determined.

• Journal of Photoscience
• /
• v.5 no.3
• /
• pp.131-135
• /
• 1998

Using differential display reverse transcription technique, the present study attempted to isolate and characterize genes specifically expressed in cotyledons of Pharbitis nil Choisy cv. Violet during floral induction. A total of 107 bands specific to the inductive condition were initially obtained with 80 primer sets of 20 different arbitrary primers combined with 4 kinds of T12MN. In northern blot analysis with reamplified cDNAs as probes, three cDNAs were detected to be expressed specificcally in the induced cotyledon tissues, and designated PnFL-1, PnFL-2 and PnFL-3 , the size of which were 228 bp, 317 bp and 272 bp, respectively. A search for sequences similar to the decuced amino acid sequences was conducted using GenBank and EMBL database ; seequence encoded by PnFL-1 had 29% identity with the clone of Arabidopsis thaliana similiar to reverse trascriptase (Genbank Acc. N0.3047086), PnFL-2 shared 50% identity with hydroxiyproline-rich glycoprotein of Glycine max(GenBank Acc. No.347455), and PnFL-3 had 46% identity with TAMU 4. Thaliana genomic clone T23E16 (GenBank Acc. No.B67574). None of them was known gene in the plant system up to date, implying that the fragments may comprise parts of genes which are associated with the floral induction in Pharbitis nil.

• International Journal of Control, Automation, and Systems
• /
• v.3 no.1
• /
• pp.79-86
• /
• 2005

In this paper, an estimator scheme for the rotor speed and flux of an induction motor is proposed on the basis of a fourth-order electrical model. It is assumed that only the stator currents and voltages are measurable, and that the stator currents are bounded. There are a number of common terms in the motor dynamics, and this is utilized to find a simple error model involving some auxiliary variables. Using this error model, the state estimation problem is converted into a parameter estimation problem assuming that the rotor speed is constant. Some stability properties are given on the basis of Lyapunov analysis. In addition, the rotor resistance, which varies with the motor temperature, can also be estimated within the same framework. The effectiveness of the proposed scheme is demonstrated through computer simulations and experiments.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.2 no.2
• /
• pp.64-70
• /
• 1988

In many applications of inverter system, it is desirable to obtain an AC output voltage with variable frequency and amplitude. For the variable-speed AC motor drive, the system is one major area of application for the variable-frequency inverter. V ariable~voltage variable-frequency sinusoidal output in three-phase inverter is possible by employing the techniques developed. In this paper, the technique of particular harmonics elimination(PHE) in three-phase PWM inverter-output waveforms is introduced. The required switching patterns are determind on personal computer. Results are stored in look-up table in EPROM and used to control the switching of the inverter devices. The experimental results indicate that the loss in an induction motor is minimized to a degree by using this algorithm. The proposed PWM pattern is effective not only to the induction motor but also to the other electromagnetic machine such as Voltage Regulator, UPS.

• Proceedings of the KIEE Conference
• /
• 2005.04a
• /
• pp.152-154
• /
• 2005

This paper is proposed a fuzzy control and neural network based on the vector controlled induction motor drive system. The hybrid combination of fuzzy control and neural network will produce a powerful representation flexibility and numerical processing capability Also, this paper is proposed estimation and control of speed of Induction motor using fuzzy and neural network. The back propagation neural network technique is used to provide a real time adaptive estimation of the motor speed. This paper is proposed the experimental results to verify the effectiveness of the new method.