• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.44 no.2
• /
• pp.112-119
• /
• 2008

The fundamental data on the catch fluctuation in the rectangular set net according to the tide age were developed based on the catches recorded from the year 1986 to 2004 in the coastal waters of Hamdeok, Jeju. Total catch by the rectangular set net had a deep connection with the tide age. In particular, during increasing tide, total catch were reduced gradually from the neap tide to the high tide. As it turned out, the slope of total catch declined by degree and showed a correlation coefficient of determination of 0.76. On the contrary, in the case of decreasing tide, there was little sign of rise in total catch. In particular, large catch seemed to occur at the next tide to the neap tide. In the relation between the catch and the tide age, the level of the correlation coefficient chosen at $p{\leq}0.05$ decreased in the order rabbitfish(-0.84) and horse mackerel(-0.71), while the significance of other dominant species were not selected.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.7 no.2
• /
• pp.23-39
• /
• 2001

Dysfunction of the anterior and dorsal muscles of the trunk have been studied in relation to low back pain of many years. Many muscles of the trunk are capable of contributing to the stabilization and protection of the lumbar spine, recent evidence has suggested that transversus abdominis may be critically involved and has been the focus of rehabilitation. The delay in onset of contraction of trunk muscles associated with movement of the upper or lower limb in patients with low back pain indicates a significant deficit in the automatic motor command for control of disturbance to the spine. The function of transversus abdominis has been largely ignored in the evaluation of spinal stabilization and protection. The most essential stabilizing muscles for the lumbar column are the transversus abdominis and the multifidus. Sling exercise therapy(SET) concept consists of a system of diagnosis and treatment. The system of diagnosis involves testing the muscle's tolerance through progressive loading in open and close kinetic chains. The SET system contains elements such as relaxation, increasing the range of movement, traction, training the stabilizing musculature, sensorimotor exercises, training in open and close kinetic chains, dynamic training of the mobilizing musculature, cardiovasc+ular exercises, group exercise, personal exercise at home. Sensorimotor training is an essential element of the SET concept. The emphasis is on closed kinetic chain exercises on an unstable surface, thereby achieving optimum stimulation of the sensorimotor apparatus.

• International Journal of CAD/CAM
• /
• v.11 no.1
• /
• pp.18-26
• /
• 2011

This paper proposes a new solid-shape modeling system based on a lusterware-image illustration. The proposed method reconstructs a three dimensional solid shape from a set of rough sketches that are typically drawn in the early stages of the design process. The sketches do not have to be strictly accurate, and this tolerance to the roughness of the input sketches is one of the major advantages of the proposed method. The proposed system creates an initial shape based on the silhouette of the input lusterware-images. Then the user can edit the initial shape with intuitive cutting and dishing-up operations, which are based on sketching user interface. To achieve the goal, the system retains the geometric model with two representations: a point-set data and a volume data. This dual data structure allows the program to create an initial shape from the input images with little computational cost, and the user can apply cutting and dishing-up operations without substantially increasing computational and memory requirements. In this research, we have tested the proposed system by reconstructing solid models of some mechanical parts from rough sketches. The experimental results indicate that the proposed method is useful for the prototyping of a solid shape.

• Journal of the Korea Furniture Society
• /
• v.23 no.4
• /
• pp.460-466
• /
• 2012

This study was conducted to investigate the surface hardness of thermally-compressed larch wood by compression set and temperature. The surface hardness of thermally-compressed larch wood increased with increasing compression set and temperature. For compression set 60%, the specific gravity was increased as 0.93. However, the surface hardness was lower value as 31.1 N/$mm^2$ compared with a similar specific gravity of the tropical timber. For density profile, less than compression set 40%, compression was observed mainly surface area. On the other hand, more than 50%, density profile variation was reduced by compression of central part. Results of this study indicate that thermally-compressed larch wood can be replace some imported hardwoods such as oak or cherry. However, thermally-compressed larch wood was difficult to replace the tropical timber being imported in terms of surface hardness.

• Journal of Animal Science and Technology
• /
• v.65 no.3
• /
• pp.490-510
• /
• 2023

Feed safety is needed to produce and provide safe animal feeds for consumers, animals, and the environment. Although feed safety regulations have been set for each country, there is a lack of clear feed safety regulations for each livestock. Feed safety regulations are mainly focused on heavy metals, mycotoxins, and pesticides. Each country has different safe levels of hazardous materials in diets. Safe levels of hazardous materials in diets are mostly set for mixed diets of general livestock. Although there is a difference in the metabolism of toxic materials among animals, the safe level of feed is not specific for individual animals. Therefore, standardized animal testing methods and toxicity studies for each animal are needed to determine the correct safe and toxic levels of hazardous materials in diets. If this goal is achieved, it will be possible to improve livestock productivity, health, and product safety by establishing appropriate feed safety regulations. It will also provide an opportunity to secure consumer confidence in feed and livestock products. Therefore, it is necessary to establish a scientific feed safety evaluation system suitable for each country's environment. The chance of outbreaks of new hazardous materials is increasing. Thus, to set up appropriate toxic levels or safe levels in feed, various toxicity methods have been used to determine toxic levels of hazardous materials for humans and animals. Appropriate toxic testing methods should be developed and used to accurately set up and identify toxicity and safe levels in food and feed.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.22 no.4
• /
• pp.41-48
• /
• 1986

To investigate the midwater trawl gear available for the Korean near sea trawlers, the authors carried out a field experiment on the attitude and the opening efficiency of the otter board with the Pusan 404 (160GT, 750ps), a training ship of National Fisheries University of Pusan. The experimental trawl gear was designed to be operable by the ship and the otter board was made of single iron plate with 12% camber ratio. The special-prepared potentiometric angle detector was used for determining the attitude, and the 50 KHz fish finder for the opening between the otter boards. The results obtained can be summarized as follows: 1. The angle of attack varied by moving the towing point on the towing plate of the otter board. It showed 33 to 36 degrees when the point was set at the outmost position, 25 to 31 degrees at the middle position and 19 to 30 degrees at the inmost position, with a decreasing tendency according to the increase of towing speed in each cases. 2. The heel of the otter board always occured inwards, increasing slightly according to the increase of towing speed. 3. The tilt of the otter board always occured outwards, increasing slightly according to the move of the towing point inwards, and decreasing slightly according to the increase of towing speed. 4. The opening between otter boards showed the largest value when the towing point was set at the outmost position.

• Journal of Information Technology Services
• /
• v.16 no.4
• /
• pp.1-13
• /
• 2017

This study examines how specific technology from Information and Communications Technology (ICT)-which plays a critical role in increasing productivity by promoting a spread of technology across the society though the use of big data, mobile or wearable devices-impacts of the productivity of society and productivity of added values, respectively. The impact of technology was studied from the perspective of efficiency levels of input. In order to provide an analysis, we have categorized ICT into 16 specific technologies and have set the number of companies and number of employees each as an input factor while setting the respective output and the output of added values as an output factor. Afterwards, we have applied data envelopment analysis (DEA) which is a form of nonparametric frontier analysis and measured the productivity and efficiency of added values for each technology. According to the analysis results, there were 2 technologies by the CRS standards, and 3 technologies by the VRS standards that showed relative efficiency levels. We have also presented some efficiency improvement strategies for specific technologies that revealed relative inefficiency and offered a reference set and projection point. In addition, we provide an analysis on scale efficiencies (SE), diminishing returns to scale (DRS), and increasing returns to scale (IRS) of each ICT.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.41 no.1
• /
• pp.110-117
• /
• 2018

Machines and facilities are physically or chemically degenerated by continuous usage. One of the results of this degeneration is the process mean shift. By the result of degeneration, non-conforming products and malfunction of machine occur. Therefore a periodic preventive resetting the process is necessary. This type of preventive action is called 'preventive maintenance policy.' Preventive maintenance presupposes that the preventive (resetting the process) cost is smaller than the cost of failure caused by the malfunction of machine. The process mean shift problem is a field of preventive maintenance. This field deals the interrelationship between the quality cost and the process resetting cost before machine breaks down. Quality cost is the sum of the non-conforming item cost and quality loss cost. Quality loss cost is due to the deviation between the quality characteristics from the target value. Under the process mean shift, the quality cost is increasing continuously whereas the process resetting cost is constant value. The objective function is total costs per unit wear, the decision variables are the wear limit (resetting period) and the initial process mean. Comparing the previous studies, we set the process variance as an increasing concave function and set the quality loss function as Cpm+ simultaneously. In the Cpm+, loss function has different cost coefficients according to the direction of the quality characteristics from target value. A numerical example is presented.

• Journal of information and communication convergence engineering
• /
• v.21 no.2
• /
• pp.117-129
• /
• 2023

High-utility itemset mining (HIUM) has emerged as a key data-mining paradigm for object-of-interest identification and recommendation systems that serve as frequent itemset identification tools, product or service recommendation systems, etc. Recently, it has gained widespread attention owing to its increasing role in business intelligence, top-N recommendation, and other enterprise solutions. Despite the increasing significance and the inability to provide swift and more accurate predictions, most at-hand solutions, including frequent itemset mining, HUIM, and high average- and fast high-utility itemset mining, are limited to coping with real-time enterprise demands. Moreover, complex computations and high memory exhaustion limit their scalability as enterprise solutions. To address these limitations, this study proposes a model to extract high-utility frequent closed itemsets based on an improved cumulative summary list structure (CSLFC-HUIM) to reduce an optimal set of candidate items in the search space. Moreover, it employs the lift score as the minimum threshold, called the cumulative utility threshold, to prune the search space optimal set of itemsets in a nested-list structure that improves computational time, costs, and memory exhaustion. Simulations over different datasets revealed that the proposed CSLFC-HUIM model outperforms other existing methods, such as closed- and frequent closed-HUIM variants, in terms of execution time and memory consumption, making it suitable for different mined items and allied intelligence of business goals.

• Journal of Environmental Science International
• /
• v.20 no.2
• /
• pp.155-161
• /
• 2011

In application and discussion of population structure and phenotypic divergence in plant community, the classic Lotka-Volterra models of competition and spatial model are conceived as a mechanism that is composed by multiple interacting processes. Both the Lotka-Volterra and spatial simulation formulae predict that species diversity increases with genotypic richness (GR). The two formulae are also in agreement that species diversity generally decreases within increasing niche breadth (NB) and increases with increasing potential genotypic range (PGR). Across the entire parameter space in the Lotka-Volterra model and most of the parameter space in the spatial simulations, variance in community composition decreased with increasing genotypic richness. This was, in large part, a consequence of selecting genotypes randomly from a set pool.