• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.14 no.3
• /
• pp.217-227
• /
• 1992

The purpose of this paper is to investigate changes in soft tissue in 22 patients treated by vertical ramus osteotomy and sagittal split ramus osteotomy for the correction of mandibular prognathism. 22 individuals, 12 males and 10 females, were selected from the patients with mandibular prognathism at the Department of Oral and Maxillofacial Surgery, Colledge of Dentistry, Kyung Hee University. Patient were analyzed with cephalogram taken 1 week before and at least 6 weeks after surgery under the same condition. Measurements were made constructed hard tissue and sop tissue points located on each before-and-after film tracing. Comparision were made of these figures to estimate the amount that the soft tissue followed the hard tissue structures in each surgical procedure : ratio of sop and hard tissue changes were formulated. The results were as follows. 1. The horizontal changes of Pogs and Bs as a ratio of the horizontal changes of Pog and B point were 1.02 and 1.16 respectively. 2. One millimeter of posterior changes at Pog resulted in 0.86mm of posterior change at Li and 0.09mm of posterior change at Ls. The greatest amount of sop tissue change occurred at Pogs, with substantially less posterior displacement at Bs, even less at Li and at least at Ls. 3. The ratio of LI to Li was 1:0.81 and the ratio of LI to Ls was not significant.(1 : 0.17) 4. The ULA(Cm-Sn-Ls) and the relative lower lip projection (LLP) was incnease4 but the relative upper lip projection (ULP) was slightly decreased 5. The angular change of the upper lip inclined angle (Ls-Sn/ANS-PNS) and lower lip inclined angle(Li-Pogs/Me-Go) expressed as a ratio of the posterior change of Pog were 0.57 and 0.20 respectively. 6. The ratio of the lower anterior facial height change of the soft tissue(Sn-Mes) to the hard tissue(ANS-Gn) were 0.78 and and the ratio of vertical height changes of the hard tissue and sop tissue to the posterior change of the Pog were 0.18 and 0.19 respectively. 7. The sop tissue angular change of facial convexity(G-Sn-Pogs) expressed as a ratio of the angular change of the hard tissue angle of facial convexity(N-A-Pog) was 1.24.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.5
• /
• pp.761-778
• /
• 2017

The need of the underground space for the infrastructures in urban area is increasing, and especially the demand for shallow tunnels increased drastically. It is very important that the shallow tunnel in the urban area should fulfill not only its own safety conditions but also the safety condition for the adjacent structures and the surrounding sub-structure. Most of the studies on the behavior of shallow tunnels concentrated only on their behaviors due to the local deformation of the tunnel, such as tunnel crown or tunnel sidewall. However, few studies have been performed for the behavior of the shallow tunnel due to the deformation of the entire tunnel. Therefore, in this study the behavior of the surrounding ground and the stability caused by deformation of the whole tunnel were studied. For that purpose, model tests were performed for the various ground surface slopes and the cover depth of the tunnel. The model tunnel (width 300 mm, height 200 mm) could be simulationally deformed in the vertical and horizontal direction. The model ground was built by using carbon rods of three types (4 mm, 6 mm, 8 mm), in various surface slopes and cover depth of the tunnel. The subsidence of ground surface, the load on the tunnel crown and the sidewall, and the transferred load near tunnel were measured. As results, the ground surface subsided above the tunnel, and its amount decreased as the distance from the tunnel increased. The influence of a tunnel ceased in a certain distance from the tunnel. At the inclined ground surface, the wider subsidence has been occurred. The loads on the crown and the sidewall were clearly visible, but there was no effect of the surface slope at a certain depth. The load transfer on the adjacent ground was larger when the cover depth (on the horizontal surface) was lager. The higher the level (on the inclined surface), the wider and smaller it appeared. On the shallow tunnel under inclined surface, the transfer of the ambient load on the tunnel sidewall (low side) was clearly visible.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.6
• /
• pp.571-578
• /
• 2012

In this paper, an experimental investigation is performed to estimate the thermal performance of a natural convective heat sink with plate fins subject to the uniform wall temperature condition. Extensive experiments are performed with various input powers, fin spacings, and heights of the natural convective heat sinks with plate fins. In particular, the effect of the inclination angle on the thermal performance of the heat sink is studied. In order to validate the experimental data, the experimental results are compared with results from previous studies. Based on the experimental results, the appropriate ranges of the previous correlations between the input power, the fin spacing, the fin height, and the inclination angle for the natural convective heat sink with plate fins are evaluated.

• Korean Journal of Child Studies
• /
• v.38 no.1
• /
• pp.127-138
• /
• 2017

Objective: This study examined differences in preschoolers' prosocial decision-making, emotion understanding in prosocial dilemmas based on the age and emotional conditions of a counterpart child, and the effects of emotion understanding on preschoolers' prosocial decision-making. Methods: The participants were 114 children (35 3-year-olds, 39 4-year-olds, and 40 5-year-olds). Each child was presented individually with prosocial dilemma tasks and was asked to make decisions and understand emotions (in prosocial and desire-fulfilled situations) based on the emotional conditions of a counterpart child. Results: First, the 4- and 5-year-olds showed more prosocial decision-making in prosocial dilemmas than the 3-year-olds. Prosocial decision-making was significantly lower when the counterpart child was angry, rather than neutral or sadness. Second, in prosocial situations, the 5-year-olds displayed higher positive emotion understanding scores than the 3-year-olds, And in desire-fulfilled situations, the 3-year-olds showed positive emotion understanding, whereas the 4- and 5-year-olds showed negative emotion understanding. Finally, children were more inclined toward prosocial decision-making when they showed higher emotion understanding in prosocial situations, lower emotion understanding in desire-fulfilled situations, and greater age. These were equal to all emotional conditions of the counterpart child. Conclusion: These results suggest that emotion understanding is an important component of social cognition, which effects preschoolers' prosocial decision-making.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1149-1156
• /
• 2008

The principle of self clamping friction clutch is presented in this paper and the transmitted torque capacity is also calculated. In order to enlarge the friction force, a part of rotating force of driving side is converted to normal force of friction materials by clamping arm. The increased normal force of friction materials assures the large friction force and the transmitted torque capacity of clutch becomes large. The self clamping friction clutch is adopted in the tube type air pressure clutch and the condition of stability is investigated. It is proven that the inclined angle of clamping arm and the friction factor of friction materials are the essential elements in stability and torque capacity of self clamping friction clutch. The transmitted torque capacity of self clamping friction clutch is compared with air pressure clutch. The normal force of friction lining is magnified by 1/(1-k) and the transmitted torque capacity is also magnified with same proportion comparing with air pressure clutch. The larger the friction factor of friction lining, the larger the magnification factor. The longer the clamping arm, the smaller the magnification factor. It must be also noted that the value of k=${\mu}Y/X$ is the criterion of stability. If the value of k=${\mu}Y/X$ is greater than or equal to 1, the self clamping friction clutch is unstable and it can not be used as clutch.

• International Journal of Fluid Machinery and Systems
• /
• v.4 no.3
• /
• pp.307-316
• /
• 2011

In order to clarify the features of tip leakage vortex near blade tip region in a half-ducted axial fan with large bellmouth, the experimental investigation was carried out using a 2-dimensional LDV system. Three sizes of tip clearance (TC) were tested: those sizes were 1mm (0.55% of blade chord length at blade tip), 2mm (1.11% of blade chord length at blade tip) and 4mm (2.22% of blade chord length at blade tip), and those were shown as TC=1mm, TC=2mm and TC=4mm, respectively. Fan characteristic tests and the velocity field measurements were done for each TC. Pressure - flow-rate characteristics and two-dimensional velocity vector maps were shown. The vortex trace and the vortex intensity distribution were also illustrated. As a result, a large difference on the pressure - flow-rate characteristics did not exist for three tip clearance sizes. In case of TC=4mm, the tip leakage vortex was outflow to downstream of rotor was not confirmed at the small and reference flow-rate conditions. Only at the large flow-rate condition, its outflow to downstream of rotor existed. In case of TC=2mm, overall vortex behaviors were almost the same ones in case of TC=4mm. However, the vortex trace inclined toward more tangential direction. In case of TC=1mm, the clear vortex was not observed for all flow-rate conditions.

• Tunnel and Underground Space
• /
• v.22 no.3
• /
• pp.205-213
• /
• 2012

In this study, scaled model tests were performed to investigate the stability of twin tunnels constructed in anisotropic rocks with $30^{\circ}$ inclined bedding planes under the condition of lateral pressure ratio, 2. Five types of test models which had respectively different pillar widths and shapes of tunnel sections were experimented, where both crack initiating pressures and deformation behaviors around tunnels were investigated. The models with shallower pillar width showed shear failure of pillar according to the existing bedding planes and they were cracked under lower pressure than the models with thicker pillar width. In order to find the effect of tunnel sectional shape on stability, the models with four centered arch section, circular section and semi-circular arch section were experimented. As results of the comparison of the crack initiating pressures and the deformation behaviors around tunnels, the semi-circular arched tunnel model was the most unstable whereas the circular tunnel model was the most stable among them. Furthermore, the results of FLAC analysis were qualitatively coincident with the experimental results.

• Korean Institute of Interior Design Journal
• /
• v.24 no.4
• /
• pp.143-151
• /
• 2015

This study was conducted under the premise that the university library's subject specialization room is in need of major modifications in order to accommodate the needs of various majors. The subject specialization room will be able to support university library users who are inclined to use the general reading room. Therefore, the study presents spatial planning for the average university library's subject specialization room by taking into account student majors. This could be a guideline for the construction and renovation of university libraries in the future. The summary of results for this study and the conclusions are as follows: 1)Natural sciences subject specialization room should be, partially connected with the humanities/social science subject specialization room in order to provide an open-concept reference room. In the shared area connecting the two subject specialization rooms needs to be installed a staff counter and subject specialist librarian service booth for users of both subject specialization rooms. 2)For humanities/social sciences subject specialization room, partially connect with the natural sciences subject specialization room. In the connecting area between the two rooms, plan an open-concept lounge for resting and reading. 3)It is best to plan subject specialization room for art/music/physical education majors separate from the subject specification room of other majors. Structurally separate art/music/physical education major subject specialization rooms from the building or plan a separate room in an art/music/physical education building. Users of art/music/physical education majors showed a high preference for a spatially separated and specialized library structure, which proves that an art/music/physical education library need to be planed based on the specialized library structure found in law school libraries or medical school libraries. Plan the center of the room with open-concept based reading room. Use wall-sides, partitions, or shelves to create reading space separate from the shelving area.

• Economic and Environmental Geology
• /
• v.13 no.3
• /
• pp.159-166
• /
• 1980

A model study was conducted for the investigation of apparent resistivity variation along with electric resistivity variation of host rock and dip variation of bed. Experiments were carried out for the cases of horizontal and dipping beds in a water tank by using Wenner and Schlumberger arrays and by changing salinity of water. The ratios of resistivity values of the bed to that of brine were 1 : 10, 1 : 50, 1 : 100 and 1 : 500. Natural coally-shale of $55cm{\times}35cm{\times}3.5cm$ was used as a bed for experimental model, and brine as a host rock. Equi-resistivity curves and characteristic curves were obtained for each case of the experiment. The equi-resistivity curve was drawn both on the cross section parallel to strike of bed and longitudinal section perpendicular to it. The characteristic curve was drawn on the cross section. In the case of dipping bed of different dips, the curves are parallel to the boundary of the bed in the upper part of the bed, and are inclined to the opposite direction with the same angle of the dip of bed in the lower part. We can deduce, from the equi-resistivity curves, the location, shape and dip of the bed. It is shown in the characteristic curves that when the ratio of resistivity value of bed to that of host rock increases, the slope of curves becomes steeper, location of low-resistivity zone lower, and the width of it narrower. The slope of curves also becomes steeper when dip of bed increases. We can deduce, from the characteristic curves, the ratio of resistivity values between adjacent beds. It was found out from the experiments that electric resistivity method could be applicable to prospecting for underground geology with an electric resistivity contrast of 1 : 10. This fact strongly suggests that distinction of coal from coally-shale could be possible in a certain field condition.

• Membrane and Water Treatment
• /
• v.7 no.2
• /
• pp.101-113
• /
• 2016

In this study, to improve the water flux of porous hydrophobic membranes, various water-soluble polymers including neutral, cationic and anionic polymers were adsorbed using 'salting-out' method. The adsorbed hydrophobic membrane surfaces were characterized mainly via the measurements of contact angles and scanning electron microscopy (SEM) images. To enhance the durability of the modified membranes, the water-soluble polymers such poly(vinyl alcohol) (PVA) were crosslinked with glutaraldehyde (GA) and found to be resistant for more than 2 months in vigorously stirred water. The water flux was much more increased when the ionic polymers used as the coating materials rather than the neutral polymer and in this case, about 70% of $0.31L/m^2{\cdot}h$ (LMH) to 0.50 LMH was increased when 300 mg/L of polyacrylamide (PAAm) was used as the coating agents. Among the cationic coating polymers such as poly(styrene sulfonic acid-co-maleic acid) (PSSA_MA), poly(acrylic acid-comaleic acid) (PAM) and poly(acrylic acid) (PAA), PSSA_MA was found to be the best in terms of contact angle and water flux. In the case of PSSA_MA, the water flux was enhanced about 80%. The low concentration of the coating solution was better to hydrophilize while the high concentration inclined to block the pores on the membrane surfaces. The best coating condition was found: (1) coating concentration 150 to 300 mg/L, (2) ionic strength 0.15, (3) coating time 20 min.