• Membrane and Water Treatment
• /
• v.6 no.3
• /
• pp.205-224
• /
• 2015

A novel hydrophilic poly (vinylidene fluoride)/poly (p-phenylene terephthalamide) (PVDF/PPTA) blend membrane was prepared by in situ polycondensation of p-phenylene diamine (PPD) and terephthaloyl chloride (TPC) in PVDF solution with subsequent nonsolvent induced phase separation (NIPS) process. For comparison, conventional solution blend membrane was prepared directly by adding PVDF powder into PPTA polycondensation solution. Blend membranes were characterized by means of viscometry, X-ray photoelectron spectroscopy (XPS), Field Emission Scanning Electron Microscopy (FESEM). The effects of different blending methods on membrane performance including water contact angle (WCA), mechanical strength, anti-fouling and anti-compression properties were investigated and compared. Stronger interactions between PVDF and PPTA in in situ blend membranes were verified by viscosity and XPS analysis. The incorporation of PPTA accelerated the demixing rate and caused the formation of a more porous structure in blend membranes. In situ blend membranes exhibited better hydrophilicity and higher tensile strength. The optimal values of WCA and tensile strength were $65^{\circ}$ and 34.1 MPa, which were reduced by 26.1% and increased by 26.3% compared with pure PVDF membrane. Additionally, antifouling properties of in situ blend membranes were greatly improved than pure PVDF membrane with an increasing of flux recovery ratio by 25%. Excellent anti-compression properties were obtained in in situ blend membranes with a stable pore morphology. The correlations among membrane formation mechanism, structure and performance were also discussed.

• Elastomers and Composites
• /
• v.33 no.4
• /
• pp.255-266
• /
• 1998

One-step continuous reactive blend with EPDM is investigated using a modular intermeshing corotating twin screw extruder This was performed via anionic polymerization mechanism. Mechanical properties were characterized and compared with mechanical blends.

• Applied Chemistry for Engineering
• /
• v.3 no.3
• /
• pp.499-506
• /
• 1992

Copolymer of Styrene and GMA(glycidyl methachylate), having reactive ratios of $r_1=0.53$, $r_2=0.44$, was synthesized in dioxane using AIBN as free radical initiator. Followed by the reaction of ethylene diamine with copolymer PGS, amine groups were introduced to the PGS(NPGS). The composition of copolymer was determined by elemental analyzer. Poly(glycidyl methacrylate) (PGMA) was obtained in benzene using AIBN as free radical initiator. The NPGS-PGMA blend of 50/50 composition was prepared by mixing these polymers in THF at $65^{\circ}C$. Glass transition temperature (Tg) of NPGS-PGMA blend was measured by DSC. The blend showed a single Tg. Accordingly, it was clear that the NPGS was compatible with PGMA. An intermolecular reaction between amine groups of NPGS and epoxy groups of PGMA imparts compatibility in the NPGS-PGMA blend. When the NPGS-PGMA blend was added to the incompatible PS-PGMA blend, PS-PGMA blend showed Tg change. Scanning Electron Micrograph(SEM) showed a fine morphology in this blend. Consequently, it was apparent that the NPGS-PGMA blend acted as a compatibilizer for the PS-PGMA blend.

• Korea-Australia Rheology Journal
• /
• v.16 no.3
• /
• pp.147-152
• /
• 2004

Ultrasound-assisted melt mixing was applied to blending polystyrene (PS) and low density polyethylene(LDPE). The influence of the ultrasonic irradiation on the morphology and mechanical properties of the blends was investigated. It was observed that the domain sizes of the blend were significantly reduced and phase stability was well sustained even after a thermal treatment. Such morphological feature was consistent with the improvements in mechanical performance of the blends. The desirable results of ultrasonic compatibilization are mainly attributed to the in-situ formation of PS-LDPE copolymers as confirmed by a proper separation experiment. An important relationship between ultrasonic irradiation time and mechanical properties is revealed and an issue on the thermal stability of the blend is discussed.

• Membrane and Water Treatment
• /
• v.8 no.4
• /
• pp.311-321
• /
• 2017

Hydrophilic and high modulus PPTA molecules were incorporated into PVDF matrix via the in situ polymerization of PPD and TPC in PVDF solution. PPTA/PVDF/NWF blend membrane was prepared through the immersion precipitation phase inversion method and nonwoven coating technique. The membrane integrated technology including PPTA/PVDF/NWF blend membrane and reverse osmosis (RO) membrane was employed to treat the polyester/viscose spunlace nonwoven process wastewater. During the consecutive running of six months, the effects of membrane integrated technology on the COD, ammonia nitrogen, suspended substance and pH value of water were studied. The results showed that the removal rate of COD, ammonia nitrogen and suspended substance filtered by PPTA/PVDF blend membrane was kept above 90%. The pH value of the permeate water was about 7.1 and the relative water flux of blend membrane remained above 90%. After the deep treatment of RO membrane, the permeate water quality can meet the water circulation requirement of spunlace process.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.10a
• /
• pp.93-93
• /
• 2003

Electrically conducting polyaniline/cyanoethyl resin (PANI/Cyan) blends were prepared by in situ polymerization. The mechanical properties of the blend films increased with increasing cyanoethyl resin and the blend films have moderate conductivity.

• Polymer(Korea)
• /
• v.24 no.1
• /
• pp.29-37
• /
• 2000

Polyaniline (PANi)/Poly(ethylene of oxide) (PEO) in-situ blends were prepared by inducing phase separation through solvent evaporation after casting from solutions containing aniline monomer, oxidant (initiator), dopant and PEO in methanol/water mixed solvent. It was observed that the electrical conductivity first increases rapidly as PANi amount in the PANi/PEO blend increases and then slowly increases as the weight percentages of polyaniline become above 11 wt% in the blend. We also noted that the morphology of PANi/PEO blends changes when the holding time in a stirrer at constant temperature is varied and eventually affects the electrical conductivity. As the length of alkyl group in dopants increases, the electrical conductivity of doped blends increases. The PANi/PEO blend prepared with a high molecular weight of PEO yields higher electrical conductivity.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.348-351
• /
• 2004

In this study, the recycled concrete aggregates crushed in-situ were used for the access road pcc (portland cement concrete) pavement. Based on laboratory results, the properties of materials, mixture proportioning, blend rates, and application conditions were investigated prior to trial application, and the various problems on recycled concrete aggregate under construction have been comprehensively checked.

• Proceedings of the Korean Society of Rheology Conference
• /
• 2002.11a
• /
• pp.143-146
• /
• 2002

No Abstract, See Full Text

• Korea-Australia Rheology Journal
• /
• v.14 no.3
• /
• pp.121-128
• /
• 2002

A series of thermoplastic polymers and their blends were melt-processed with high intensity ultrasonic wave in an intensive mixer. For the effective transfer of ultrasonic energy, an experimental apparatus was specially designed so that polymer melt can directly contact with ultrasonic horn. It was observed that significant variations in the rheological properties of polymers occur due to the unique action of ultrasonic wave without any aid of chemical additives. It was also found that the direct sonication on immiscible polymer blends in melt state reduces the domain sizes considerably and stabilizes the phase morphology of the blends. The degree of compatibilization was strongly affected by viscosity ratio of the components and the morphology was stable after annealing in properly compatibilized blends. It is suggested that ultrasound assisted melt mixing can lead to in-situ copolymer formation between the components and consequently provide an effective route to compatibilize immiscible polymer blends.