• Tunnel and Underground Space
• /
• v.32 no.6
• /
• pp.530-548
• /
• 2022

The site selection process for deep geological disposal of high-level radioactive waste will be conducted in stages, and 103 evaluation parameters related to site selection have been proposed. In the field of rock mechanics and rock engineering, there are 33 evaluation parameters for intact rock, joint and rock mass, and they are applied in the basic and detailed investigation stages. In this report, uniaxial compressive strength, in-situ stress, joint distribution, and rock mass classification were selected as the main evaluation parameters, and among them, uniaxial compressive strength and in situ stress were selected as key evaluation parameters. Statistical techniques or regression analysis were performed for granite in Wonju and Chuncheon to evaluate the distribution range for the selected key evaluation parameters. The average of the uniaxial compressive strength in the Wonju area estimated through the posterior distribution is about 171 MPa, and about 123 MPa in the Chuncheon area. The maximum in situ stress acting in the Wonju area was less than 30 MPa and less than 40 MPa in the Chuncheon area. The direction of the maximum horizontal stress calculated by regression analysis was 101° in Wonju, and in the case of Chuncheon, it was 95°, respectiviely.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.2
• /
• pp.15-21
• /
• 2012

It is difficult to determine the strength and the permeability of a soil levee quantitatively because the damages of a levee have been evaluated only by visual inspection in Korea. Therefore, it is necessary to develop a simplified measurement device for measuring the strength and permeability of a levee. In this paper, a new in-situ permeability measuring device which can measure strength and permeability based on GWP is developed and its applicability to the field permeability test of a soil levee is introduced. From the laboratory and in-situ experiments, the new measuring device has the potential of measuring the soil permeability simply and accurately.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.2C
• /
• pp.95-107
• /
• 2010

To calculate the end bearing capacity of a drilled Shaft socketed into the rockmass, the unconfined compression strength could be used. But it is difficult to find the unconfined compression strength because it is impossible to get undisturbed samples in weathered soils and rocks. So, to calculate the end bearing capacity, the existing bearing formula could not be used. In this study, for five zones (near pile tip, tip~lower 1D, tip~lower 2D, upper 1D~lower 1D, upper 1D~lower 2D), the relationships between the characteristic values of in-situ tests(SPT, DCPT PMT, BST) and the end bearing capacity of drilled shafts were analysed. As a result, DCPT results were represented the best credibility. Also, a design chart of end bearing capacity using DCPT was suggested.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.04a
• /
• pp.44.1-44.1
• /
• 2000

• Journal of the Korean Geotechnical Society
• /
• v.32 no.8
• /
• pp.15-25
• /
• 2016

In order to analyze undrained shear strength for clayey silt with low plasticity from Hwaseong site, a series of laboratory and in-situ tests were performed. The Unconfined Compressive (UC) test and Simple Consolidated-Undrained Triaxial (SCU) test were examined in order to assess their applicability to the measurement of the undrained strength of this soil. In the case of clayey silt with low plasticity, although the samples were properly taken by undisturbed sampling method, the residual effective stress and the unconfined compressive strength were reduced considerably. Therefore, an effective confining pressure that corresponds to the typical marine clay should be applied to the soil specimen before shearing in order to compensate for the loss of residual effective stress. By evaluating the shear strengths of clayey silt with low plasticity as 75% of $s_{u(scu)}$, the in-situ shear strength of this kind of soil can be duplicated.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.89-94
• /
• 1999

The workability of high strength concrete using high range water reducing admixture is varied rapidly according to elapsed time. For using the high strength concrete in situ, careful caution on workability is necessary. By using fly ash as a admixture, the slump loss of concrete can be reduced considerably, but the early strength of concrete used fly ash is smaller than that not used fly ash. For the purpose of elevating the utilization of fly ash on high strength concrete, the high fluidity retention and the strength development in early age are necessary in concrete used fly ash. In this study, to improve the fluidity retention and to acquire strength development on concrete used fly ash, the gypsum is applied.

• Geomechanics and Engineering
• /
• v.16 no.3
• /
• pp.321-329
• /
• 2018

Classic braced walls use struts and wales to minimize ground movements induced by deep excavation. However, the installation of struts and wales is a time-consuming process and confines the work space. To secure a work space around the retaining structure, an anchoring system works in conjunction with a braced wall. However, anchoring cannot perform well when the shear strength of soil is low. In such a case, innovative retaining systems are required in excavation. This study proposes an innovative earth-retaining wall that uses in situ soil confined in dual sheet piles as a structural component. A numerical study was conducted to evaluate the stability of the proposed structure in cohesionless dry soil and establish a design chart. The displacement and factor of safety of the structural member were monitored and evaluated. According to the results, an increase in the clearance distance increases the depth of safe excavation. For a conservative design to secure the stability of the earth-retaining structure in cohesionless dry soil, the clearance distance should exceed 2 m, and the embedded depth should exceed 40% of the wall height. The results suggest that the proposed method can be used for 14 m of excavation without any internal support structure. The design chart can be used for the preliminary design of an earth-retaining structure using in situ soil with dual steel sheet piles in cohesionless dry soil.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04a
• /
• pp.141-146
• /
• 1998

In the present study, we have developed high strength concrete which is adequate for the long span PC beam above 40 meters. We have selected the most adequate materials for high strength concrete through laboratory tests and in-situ mock-up applications. We verified and decided the best curing condition of high strength concrete, and suggests the optimum mix design of high strength concrete. In the future, we will verify the properties-fresh and hardened concrete- of high strength concrete and its serviceability, and also apply the high strength concrete to newly-constructed real bridge structure.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1989.10a
• /
• pp.69-72
• /
• 1989

It is widely recognized that the strength of reinforced concrete members has characteristics of random variations due to the variability of the mechanical properties of concrete and steel, the dimensional error as well as incorrect placement of reinforcing bars. In those sources of randomness, variations in concrete strength may be the one affecting the strength of R.C. members most. The concrete strength is usually assumed to have large uncertainty due to the variations in many factors, such as material properties, proportions of the concrete mix, methods of mixing, transporting, placing and curing, etc. In this study, the random characteristics inherent in the strength of field-cast concrete have been examined based on the data collected by testing standard cylinders made of field-cast concrete and cured under in-situ condition.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.51 no.3
• /
• pp.405-413
• /
• 2015

Acoustic target strength (TS) measurement and theoretical acoustic scattering models were applied to estimate the TS for assessing the fish biomass. TS measurement was made of ex situ sailfin sandfish Arctoscopus japonicus at 70 and 120 kHz, and then compared to backscatter model prediction. The live sandfish was tethered in seawater using monofilament lines. Measurements were made versus incidence angle, $-50^{\circ}$ to $50^{\circ}$ relative to dorsal aspect directions. Distorted wave Born approximation (DWBA) model was used to calculated TS pattern. The TS values of sandfish (body length: 16.2 cm) at 70 and 120 kHz were -66.94 dB and -64.45 dB, respectively, and were about 20 dB lower than TS of other fishes in Korea waters. These TS levels were distributed within the range of the theoretical TS. Ex situ measurement and theoretical TS may be applied to improve acoustical detection and biomass estimation of the sandfish, and is necessary to measure with various lengths.