• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.99.4-99
• /
• 2001

PMAC(Permanent magnet AC) motor drives are widely used in the industrial applications and home appliances because of high torque ratio, high efficiency and precise control performance. In recent years there has been a significant development of PMAC motors of various kinds. Improvements in the properties of permanent magnet materials have increased the viability of related types of motors. However, precise speed and position information is essential for the good control performance. In order to produce correct torque, the rotor flux position information from position sensor has to be identified. In this paper, a low cost position sensor is proposed for improving of starting and low speed performance of PMAC. The proposed position ...

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.149-154
• /
• 2002

In a high speed spindle system, it is very important to monitor the state of rotating rotor. Particularly in active control spindle system, the position sensor must provide feedback to the control system on the exact position of the rotor. In order to monitor the state of a high speed spindle exactly, high accuracy and wide frequency bandwidth of sensors are important. This paper observes the factors which has an effect on dynamic performances of inductive position sensor.

• Journal of International Academy of Physical Therapy Research
• /
• v.12 no.2
• /
• pp.2345-2353
• /
• 2021

Background: This study evaluated the effectiveness of upper thoracic manipulation (UTM) and proprioceptive training versus proprioceptive training alone on forward head posture (FHP) and cervicocephalic joint position sense (CJPS) in asymptomatic university students during a short interval of time. Objectives: To evaluate whether the suggested combination would provide greater benefit, and be superior to proprioceptive training alone in improving proprioceptive acuity and head posture. Design: A single-blind randomized controlled trial. Methods: Thirty-three university student volunteers with asymptomatic FHP were recruited. Subjects were randomly assigned to a manipulation group (n=16) receiving UTM combined with proprioceptive training or a proprioception group (n=17) receiving proprioceptive training only. The intervention period lasted 5 weeks in total, and consisted of one 15 to 20-minute session per week. FHP and CJPS were assessed before and after the intervention. Results: A significant pre- to post-intervention decrease in FHP and joint position error was identified in both groups (P<.05). Subjects in the manipulation group demonstrated greater improvements in CJPS and head posture compared to the proprioception group (P<.05). Conclusion: These findings support employing either intervention for treating asymptomatic students with FHP. However, the addition of UTM to proprioceptive training was more effective than proprioceptive training alone in reducing joint position errors and improving head posture.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.14 no.4
• /
• pp.288-294
• /
• 2014

Understanding a ship's present position has been one of the most important tasks during a ship's voyage, in both ancient and modern times. Particularly, a ship's dead reckoning (DR) has been used for predicting traffic situations and collision avoidance actions. However, the current system that uses the traditional method of calculating DR employs the received position and speed data only. Therefore, it is not applicable for predicting navigation within the harbor limits, owing to the frequent changes in the ship's course and speed in this region. In this study, planned routes were applied for improving the reliability of the proposed system and predicting the traffic patterns in advance. The proposed method of determining the dead reckoning position (DRP) uses not only the ships' received data but also the navigational patterns and tracking data in harbor limits. The Mercator sailing formulas were used for calculating the ships' DRPs and planned routes. The data on the traffic patterns were collected from the automatic identification system and analyzed using MATLAB. Two randomly chosen ships were analyzed for simulating their tracks and comparing the DR method during the timeframes of the ships' movement. The proposed method of calculating DR, combined with the information on planned routes and DRPs, is expected to contribute towards improving the decision-making abilities of operators.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.1
• /
• pp.477-483
• /
• 2019

In this paper, we propose vanishing-point position-improvement algorithms by using multiple images and a homography matrix. Vanishing points can be detected from a single image, but the positions of detected vanishing points can be improved if we adjust their positions by using information from multiple images. More accurate indoor space information detection is possible through vanishing points with improved positional accuracy. To adjust a position, we take three images and detect the information, detect the homography matrix between the walls of the images, and convert the vanishing point positions using the detected homography. Finally, we find an optimal position among the converted vanishing points and improve the vanishing point position. The experimental results compared an existing algorithm and the proposed algorithm. With the proposed algorithm, we confirmed that the error angle to the vanishing point position was reduced by about 1.62%, and more accurate vanishing point detection was possible. In addition, we can confirm that the layout detected by using improved vanishing points through the proposed algorithm is more accurate than the result from the existing algorithm.

• Journal of Advanced Navigation Technology
• /
• v.25 no.6
• /
• pp.441-449
• /
• 2021

With advances in autonomous vehicles, there is a growing demand for more accurate position estimation. Especially, this is a case for a moving robot for the indoor operation which necessitates the higher accuracy in position estimation when the robot is required to execute the task at a predestined location. Thus, a method for improving the position estimation which is applicable to both the fixed and the moving object is proposed. The proposed method exploits the initial position estimation from Bluetooth beacon signals as observation signals. Then, it estimates the gravitational acceleration applied to each axis in an inertial frame coordinate through computing roll and pitch angles and combining them with magnetometer measurements to compute yaw angle. Finally, it refines the control inputs for an object with motion dynamics by computing acceleration on each axis, which is used for improving the performance of Kalman filter. The experimental assessment of the proposed algorithm shows that it improves the position estimation accuracy in comparison to a conventional Kalman filter in terms of average error distance at both the fixed and moving states.

• Journal of Microbiology and Biotechnology
• /
• v.13 no.5
• /
• pp.789-793
• /
• 2003

This study focused on the optimization of the illumination method for efficient use of light energies in a photobioreactor. In order to investigate the effect of radiator position, a model simulation study was carried out using Synechococcus sp. PCC 6301 and an internally radiating photobioreactor as a model system. The efficiency of light transfer in a photobioreactor was analyzed by estimating the average light intensity in a photobioreactor. The simulation result, indicate that there exists an optimal position of internal radiators, and that the optimal position varies with radiator number and cell concentration. When light radiators are placed at the optimal position, the average light intensity is about 30% higher than that obtained by placing radiators at the circumstance or center of a photobioreactor. The method presented in this work may be useful for improving light transfer efficiency in a photobioreactor.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.1
• /
• pp.109-116
• /
• 1998

This paper is concerned with effective operating method of pneumatic on-off valves for improving position control accuracy, valve life-time and position settling time using modified pulse width modulation with dead-zone (MPWMD). The pneumatic system using on-off valves has advantage of simple construction and low cost compared with a system with servo-valves. The performance of the proposed control method is investigated experimentally for the position control of a pneumatic cylinder using on-off valves. Experimental results show that the proposed algorithm for valve operation can be used to obtain fast and accurate position control compared to the conventional PWMD algorithm. It is also shown that the use of the proposed MPWMD algorithm for the position control significantly reduces the number of valve switching and noise.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.212-216
• /
• 1998

For a Switched Reluctance Motor(SRM) drive, the important things are 1) reducing torque ripple, 2) improving efficiency, 3) sensorless speed control, 4) accurate position. The position information impotant for the efficiency and smoothness drives. Since SRMs characteristics are nonlinear. It is difficult to estimated phase current in saturation region. This paper describes a method for indirect sensing of the rotor position in SRM which use both voltage and current. The method obtains rotor position by using unconducting phase. The information about the rotor position is achieved by differentiating the unconducting phase current or the voltage gradient. And then, this paper presents a torque control with indirect rotor position detection methods. This torque control is achieved by developing a detailed nonlinear model of the motor.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.107.5-107
• /
• 2001

In this report, as the active position measurement system, a new method for two-dimensional position measurement system using a concept of semi-open type signal field has proposed. The feature of this system is realizing a position measurement only by scanning the encoded laser beams from scanning points to a measurement field, and observed it. First, both system configuration and encoding method are considered concretely, and M-sequence signal is selected for encoding. Next system design is performed to realize the theoretical measurement accuracy, and applied to a position measurement experiments. Experimental results show that measurement precision is larger than theoretical values. Furthermore, method for improving the measurement ...