• Journal of ILASS-Korea
• /
• v.3 no.1
• /
• pp.19-26
• /
• 1998

The effect of mixture component makes a nelay time and a long total combustion period $\tau_{p\;max}$. The flame propagation delay $\tau_{df}$ was determined by the record of current ion. The pressure release delay $\tau_{dp}$ and $\tau_{p\;max}$ were determined by the indicated pressure diagram in constant volume of the combustion chamber. The results are as follows: 1) The ignition delay $\tau_t$ time takes the minimum value around $\Phi=1.15$. 2) $\tau_{df}$ and $\tau_t$ time increased according to the increases of the concentrated dilution gases, because the adiabatic flame temperature decreased due to the increases of the heat capacity. But dilution gases have little effect on flame nucleus formation delay 3) The relation between $\tau_t$ time and reciprocal laminar burning velocity is almost linear. 4) The increase of the propagation length is accompanied with increased ratio of the $\tau_{df},\;\tau_{dp},\;\tau_{t},\;\tau_{p\;max}$.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.5
• /
• pp.37-42
• /
• 2011

The main objective of this study was to evaluate the current condition of harbor sediments and to estimate biochemical methane potentials from the harbor sediments. Sediment samples were collected from 10 different sampling sites. Ignition loss, elemental analyses, X-ray diffraction(XRD), X-ray fluorescence(XRF) tests were conducted to determine characteristics of the sediment. All sediments had similar elemental compositions and ignition loss were 8~10%. From the conventional BMP tests for 5 samples, cumulative methane production ranged from 11.9~15.5mL methane/(g of volatile solids), which were significantly lower than that for foods and paper. However, methane production rates for sediments were 5 to 20 times faster than those for foods and paper.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.8
• /
• pp.49-54
• /
• 2015

Molded Circucit Breaker(MCCB) is a most widely used device to protect loads from the over-current in low power level distribution system. When the MCCB interrupts the over-current, the arc discharge occurred between fixed contact and moving contact to create hot gas. By the Lorentz force due to arc current, the occurred arc is bent to the grids. The grids extend and cool and divide it for arc extinguish. In the majority cases, the MCCB protects loads by interrupting the over-current successfully but in some cases the re-ignition is occurred by hot-gas created during process of interruption. The re-ignition arises when the recovery voltage(RV) is more higher than the recovery strength between contacts and it leads to interruption fault. Therefore to find out the dielectric recovery characteristics of protecting device has a great importance for preventing interruption fault. In this paper, we studies measurement method of the dielectric recovery characteristics considering inherent attribute of the MCCB. To measure the dielectric recovery characteristic of MCCB, we makes an experiment circuit for applying the over-current and the randomly recovery voltage. The measurement methode to find out the dielectric recovery voltage of the MCCB was established and the result was based on experiment results.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2005.11a
• /
• pp.196-200
• /
• 2005

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.2
• /
• pp.461-468
• /
• 2010

This paper presents a simple digital LCD backlight inverter using a single-chip microcontroller. The proposed inverter reduces the ignition voltage and eliminates the current spikes and hence improves the ignition behavior of the cold cathode fluorescent lamp(CCFL). Thus it increases the CCFL's life span. This is achieved by implementing a digital dimming control algorithm, that contains the soft-starting algorithm, all on a single-chip microcontroller. The inverter utilizes the full-bridge resonant circuit topology. The design example along with a simple analysis for the inverter is shown, and the experimental results of the designed prototype results in close agreement with the theoretical analysis and explanation. The overall system's power efficiency is approximately 85%. Compared with conventional inverters, the ignition voltage is reduced by around 30% without any lamp current spike occurring during the dimming control operation.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.6
• /
• pp.8-17
• /
• 2010

This paper proposes a novel LCD CCFL-backlight electronic ballast using the phase-shift full-bridge inverter. The proposed electronic ballast reduces the ignition voltage and eliminates current spikes using the new digital dimming control applied with soft-starting. Thus the electronic ballast improves ignition behavior of the CCFL and hence increases the CCFL's life span. For this, this paper analyzes the full-bridge inverter topology of the proposed electronic ballast and explains the new digital dimming control algorithm applied to the ballast, briefly. And this paper shows a design example of the prototype circuit and explains an implementation method of the digital dimming control which is implemented on a single-chip microcontroller with software. This was implemented as actual prototype electronic ballast, and its experimental results showed that the proposed electronic ballast operates correctly. The ignition voltage of the prototype in the digital dimming operation was reduced about 30[%] compared with the conventional electronic ballast and there were not any current spikes.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.273-276
• /
• 2005

This paper presents an electronic ballast using a step down converter, a low frequency inverter for high pressure discharge lamp. The proposed ballast is composed of a full-wave rectifier, a step down converter operated as a current source with power regulation and a low frequency inverter with ignition circuit. The ignition circuit generates high voltage pulse of 1${\sim}$2[kV] peak, 130[Hz]. Moreover, it is able to reignite at regular intervals by protective circuit. As experimental results on the test, lamp voltage, current and consumption power are measured 132.5[V], 7.6[A] and 1,005[W], respectively. It was confirmed that the designed ballast operate the lamp with a constant power.

• Proceedings of the KIEE Conference
• /
• 2002.11b
• /
• pp.50-52
• /
• 2002

Distance relays need accurate current and voltage for determining the trip ignition. Therefore we must analyze nonlinear phenomena which cause distortion in signals first of all. This paper presents the effect of some distortion(arcing fault and current transformer saturation) in power system. The saturation of a current transformer distorts input current of a distance relay and arcing faults make current and voltage to be changed. This paper describes modeling methods of a current transformer and arcing faults, and describes the simulation result of two distance relay algorithms (discrete fourier transform and modified differential equation methods)

• Journal of the Korean Society of Safety
• /
• v.31 no.2
• /
• pp.18-25
• /
• 2016

The incandescent lamp is an electric light fixture with a tungsten filament heated to a high temperature, by passing an electric current through it, until it glows with visible light. The hot filament is protected from oxidation with a glass bulb that is filled with inert gas. The incandescent lamp has fire risk when combustible materials are close to its glass bulb. Because its lamp has the property which converts 90~95 percents of the electric power to heat energy. 2015 national fire statistics show that fires caused by lighting fixtures were 652 cases, and incandescent lamps(44 cases) and halogen lamps(53 cases) accounted for 15 percents in those of high heating light fixtures. Since incandescent lamp fires account for about 45 percents in the high heating light fixture, we could not overlook the fire risks by the incandescent lamp. Although many studies related with those have been conducted, incandescent lamp fires are continuously occurred. This study was carried out to study the fire risk of ignition of wood due to radiant heat of incandescent lamp. Radiant heat flux of the incandescent lamp was predicted by applying point source model, and critical distance for ignition of wood was calculated by applying integral model. The results from this study could applied to fire prevention activities related to light bulb, and it could be used in fire cause investigations related to radiant heat of incandescent lamp.

• Proceedings of the KIEE Conference
• /
• 2008.04c
• /
• pp.149-151
• /
• 2008

This paper presents an architecture for driving multiple parallel cold cathode fluorescent lamps (CCFLs) for back lighting applications. The key to the architecture is a proposed capacitive coupling approach for lamp ignition. This system is consist of a flyback converter, a single inverter to drive multiple lamps and conductive floating reflector. The topology is capable of driving a number of parallel lamps with independent accurate lamp, current regulation and improving cost effectiveness with significant reduction in size and weight, compared to typical high frequency ac ballast. Experimental demonstration results for ten of parallel CCFLs with simultaneous ignition.