• Tribology and Lubricants
• /
• 제24권5호
• /
• pp.241-249
• /
• 2008

This paper describes the tribological effects on the nonlinear behavior of a spur gear pair with one-way clutch according to the direct contact elastic deformation model over a wide range of speeds, considering the hydrodynamic effects. The effects of various lubrication parameters, such as viscosity, film width, and friction, on the nonlinear dynamic behavior were analyzed. Forces due to the entraining velocity and the hydrodynamic friction were about two orders smaller than normal forces over the whole speed range. While the viscosity has a strong effect on the behavior of gear pair systems, friction has very little effect on torsional behavior. The inclusion of the hydrodynamic effect facilitates nonlinearity by increasing the overlap and damping, as well as decreasing elastic deformation and tooth reaction forces.

• 한국전산구조공학회논문집
• /
• 제24권6호
• /
• pp.601-608
• /
• 2011

부유구조체의 설계를 위해서는 파랑하중하에서 부유구조체의 파랑운동 특성과 구조거동에 대한 평가가 요구된다. 부유구조체의 구조거동 평가에서는 파랑하중에 의한 파압분포가 반영되어야 하지만, hydrodynamic 해석모델과 구조해석 모델사이의 파압 연계가 어려워 정확한 구조거동 평가가 어려웠던 문제점이 있었다. 본 논문에서는 파랑하중하에서 대형 부유구조체의 정확한 구조거동 평가를 목적으로 파랑운동-구조거동 통합해석을 실시하였다. AQWA에 의한 hydrodynamic 해석을 바탕으로 부유구조체에 작용하는 파압 분포를 ANSYS Inc.에서 제공하는 Workbench 인터페이스를 이용하여 ANSYS의 구조해석 모델에 연계하였다. 연구결과 본 연구의 파랑운동-구조거동 통합해석은 파랑하중에 의해 부유구조체에 발생하는 파압분포를 구조해석 모델에 정확하게 반영할 수 있어 파랑하중에 의한 부유구조체의 구조거동을 정확하게 평가할 수 있는 것으로 나타났다. 또한, 상부 슬래브의 인장응력은 파랑 입사각 $0^{\circ}$의 경우에 가장 불리하고, 하부 슬래브의 인장응력은 파랑 입사각 $45^{\circ}$의 경우에 가장 불리한 것으로 나타났다.

• 상하수도학회지
• /
• 제18권5호
• /
• pp.656-665
• /
• 2004

An Ozone reaction model combined with CFD(Computational Fluid Dynamics) technique was developed in this research, in the simulation of ozonation, hydrodynamic behavior as well as reaction model is important because ozone is supplied to treated water as gas ozone. In order to evaluate hydrodynamic behavior in an ozone contactor, CFD technique was applied. CFD technique elucidated hydrodynamic behavior in the selected ozone contactor, which consisted of three main chambers. Three back-mixing zones were found in the contactor. The higher velocities of water were observed in the second and third compartments than that in the first compartment. The flow of the opposite direction to the main flow was observed near the water surface. Based on the results of CFD simulation, the ozone contactor was divided into small compartments. Mass balance equations were established were established in each compartment with reaction terms. This reaction model was intended to predict dissolved ozone concentration, especially. We concluded that the model could predict favorably the mass balance of ozone, namely absorption efficiency of gaseous ozone, dissolved ozone concentration and ozone consumption. After establishing the model, we discussed the effect of concentration of gaseous ozone at inlet, temperature and organic compounds on dissolved ozone concentration.

• Ocean Systems Engineering
• /
• 제3권1호
• /
• pp.35-53
• /
• 2013

In this study, a hybrid floating structure with cylinder was introduced to reduce the hydrodynamic motions of the pontoon type. The hybrid floating structure is composed of cylinders and semi-opened side sections to penetrate the wave impact energy. In order to exactly investigate the hydrodynamic motions and structural behavior of the hybrid floating structure under the wave loadings, integrated analysis of hydrodynamic and structural behavior were carried out on the hybrid floating structure. Firstly, the hydrodynamic analyses were performed on the hybrid and pontoon models. Then, the wave-induced hydrodynamic pressures resulting from hydrodynamic analysis were directly mapped to the structural analysis model. And, finally, the structural analyses were carried out on the hybrid and pontoon models. As a result of this study, it was learned that the hybrid model of this study was showed to have more favorable hydrodynamic motions than the pontoon model. The surge motion was indicated even smaller motion at all over wave periods from 4.0 to 10.0 sec, and the heave and pitch motions indicated smaller motions beyond its wave period of 6.5 sec. However, the hybrid model was shown more unfavorable structural behavior than the pontoon model. High concentrated stress occurred at the bottom slab of the bow and stern part where the cylinder wall was connected to the bottom slab. Also, the hybrid model behaved with the elastic body motion due to weak stiffness of floating body and caused a large stress variation at the pure slab section between the cylinder walls. Hence, in order to overcome these problems, some alternatives which could be easily obtained from the simple modification of structural details were proposed.

• International Journal of Aeronautical and Space Sciences
• /
• 제16권1호
• /
• pp.41-49
• /
• 2015

Analysis and test of hydrodynamic ram in welded metallic tanks containing water were performed to investigate the phenomena and to understand the effects on the resulting structural behavior. Arbitrary Lagrange-Euler coupling method was used for the analysis of the fluid-structure interaction occurring in the hydrodynamic ram, where the projectile, tank, and water are exchanging load, momentum, and energy during the traveling of the projectile through the water of the tank. For a better representation of the physical phenomena, modeling of the welded edges is added to the analysis to simulate the earlier weld line fracture and its influence on the resulting hydrodynamic ram behavior. Corresponding hydrodynamic tests were performed in a modified gas gun facility, and the following panel-based examinations of various parameters, such as displacement, velocity, stress, and energy, as well as hydrodynamic ram pressure show that the analysis and test are well correlated, and thus the results of the study reasonably explain the characteristics of the hydrodynamic ram. The methodology and procedures of the present study are applicable to the hydrodynamic ram assessment of airframe survivability design concepts.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.628-635
• /
• 2001

Hydrodynamic behavior and response of vertical-cylindrical liquid-storage tank is considered. The equation of the liquid motion is shown by Laplace's differential equation with the fluid velocity potential. The solution of the Laplace's differential equation of the liquid motion is expressed with the modified Bessel functions. Only rigid tank is studied. The effective masses and heights for the tank contents are presented for engineering design model.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.66-68
• /
• 2009

Most hard disk spindles currently used are supported by oil lubricated hydrodynamic bearings. However, in the trend of increasing spindle speed and reducing size and cost, dynamic behaviors of the bearing such as RRO and NRRO are more important. A novel system evaluating dynamic behavior of hydrodynamic bearings in had disk drive was developed to analyze the effect of groove shapes and parameters.

• Corrosion Science and Technology
• /
• 제14권5호
• /
• pp.218-225
• /
• 2015

The electrochemical behaviors of various metals with and without diamond-like-carbon (DLC) coating in 3.5 wt% NaCl solution were investigated. The effect of hydrodynamic conditions was focused by employing a rotating disc electrode (RDE). The experimental results showed that each bare metal had a more positive corrosion potential and a higher corrosion rate due to enhanced oxygen transport at the higher rotating speed of the RDE. DLC coating caused a substantial increase in the corrosion resistance of all metals studied. However, localized corrosion was still found in the DLC-coated metal at sites where deposition defects existed. Surface morphology examination was performed after the electrochemical test to confirm the roles of hydrodynamic conditions and DLC coating.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 가을 학술발표회 논문집
• /
• pp.705-712
• /
• 2002

Geotextile tube is environmentally sustainable technology and has been applied in hydraulic and coastal engineering applications. Geotextile tube is composed in permeable fabrics and Inside dredged materials, and hydraulically or mechanically filled with dredged materials. These tube are generally about 1.0m to 2.0m in diameter, through they can be sized for any application. The tubes can be used solely, or stacked to add greater height and usability. Stacked geotextile tubes will create by adding the height necessary for some breakwaters and embankment, therefore increasing the usability of geotextile tubes. This paper presents the hydrodynamic behavior of stacked geotextile tube by hydraulic model tests. The hydraulic model test conducted by structural condition and wave conditions. Structural condition is installation direction to the wave(perpendicular band 45$^{\circ}$), and wave condition is varied with the significant wave height ranging from 3.0m to 6.0m. Based on the test results, the hydrodynamic behaviors such as structural stability, wave control capacity, and strain are interpreted.

• 한국정밀공학회지
• /
• 제29권3호
• /
• pp.295-301
• /
• 2012

The method for spraying of liquids through an electrical field has become a printing method since it can make very small droplet. For electro-hydrodynamic jet printing to become a reliable jetting tool, the jetting performance should be characterized with respect to various jetting conditions. To optimize jetting conditions, the jetting behavior should be measured. In this study, we present a visualization techniques to measure jetting behavior from electro-hydrodynamic (EHD) inkjet head. Unlike most previous method, we use the CCD camera to measure the jetting behavior. For this purpose, LED light is synchronized with jetting signal and sequential image was obtained by adjusting the delay time of the LED light. Finally, merits and demerits of using CCD camera were discussed to measure jetting image from EHD inkjet head.