• 한국생산제조학회지
• /
• 제5권3호
• /
• pp.22-30
• /
• 1996

In order to compensate for out-of-straightness of shafts, an automatic straightening process composed of an automatic measuring module, an automatic control unit and operating softwares was developed with a hydraulic press. The out-of-sraightness of each shaft was measured automatically in the measuring stage. An optimal pressure point was determined to minimize TIR value of the shaft according to press count of 3-points bending process. In the geometric adaptive control procedure, punch stroke and springback of the shaft were predicted by an observer using on-line measured values of press force and deflection amount I each press count. An automatic straightening machine was realized with the measuring module, the GAC module, PLD, IBM-PC and the operating software on the hydraulic press. the validity of the proposed straightening process was confirmed through a series of experiments with cam shafts.

• Structural Engineering and Mechanics
• /
• 제32권5호
• /
• pp.701-704
• /
• 2009

• 한국정밀공학회지
• /
• 제13권5호
• /
• pp.157-163
• /
• 1996

This paper is concered on the development of low-cost fine blanking die with two fluid chambers of which the pressure can be controlled by a hydraulic unit and its application to producting circular blanks in a conventional hydraulic press, not in a special triple-action press usually adopte in fine blanking operation. Four important working parameters affecting on the precision accuracy of products such as existence and position of Vee-ring, stripping force and counter punching force are primarily considered for experiments. Finite element analysis by suing ABAQUA software is approxi- mately made for blanking of circular specimen with a flat stripper plate and then compared with experimental measurements. The the theoretical prediction of camber height which represents deflection of a dish-shaped specimen after blanking seems to give a qualitatively good agreement. It is shown through experiments the the camber height decreases with decreasing stripping force and also with increasing counter punching force, but particularly depending on the latter much more than the former.

• Structural Engineering and Mechanics
• /
• 제52권6호
• /
• pp.1257-1271
• /
• 2014

The hydraulic deterioration of the drainage system in tunnel linings is one of the main factors governing long-term lining-ground interactions during the lifetime of tunnels. Thus, in the design procedure of a tunnel below the groundwater table, the possible detrimental effects associated with the hydraulic deterioration should be addressed. Hydraulic deterioration in double-lined tunnels can occur because of reasons such as clogging of the drainage layer and drain-pipe blockings. In this study, the coupled mechanical and hydraulic interactions between linings due to drain-pipe blockings are investigated using the finite-element method. A double-lined structural model incorporating hydraulic behavior is developed to represent the coupled structural and hydraulic behavior between the linings and drainage system. It is found that hydraulic deterioration hinders flow into the tunnel, causing asymmetric development of pore-water pressure and consequent detrimental effects to the secondary lining.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.598-602
• /
• 1996

This study is performed for investigating the effects of stripping and counter punching force on shearing characteristics in fine blanking, such as camber, burr-height and dimensional accuracy, etc by experiments. Conventional hydraulic press equipped with specially designed hydraulic unit is used for experiments so that both the stripping force and counter punching force are arbitrarily adjusted according to experimental conditions. Two kinds of materials, hot rolled steel sheet(1mm, 3mm) and pure aluminum(1mm, 3mm) are selected in order to examine the influence of strength and thickness of working materials in blanking of T-shaped products. Based on the experimental results of this study, it can be concluded that the finely cut surface of sheared blank can be obtained even in conventional hydraulic press if additional equipments and special dies are employed.

• 제어로봇시스템학회논문지
• /
• 제11권11호
• /
• pp.950-955
• /
• 2005

A automatic component inserting system for industrial PCB is developed in this paper. This system has not been developed in Korea. Most domestic companies produce PCB manually. This process requires highly-skilled staff. Therefor, we developed a PCB inserting system for automation of the process and improved productivity. There are low parts in this system; press, table, tool change and control part. A hybrid press cylinder with pneumatic and hydraulic is used in the press part. The table part consists of pneumatic actuators, stepping motors and ball-screw mechanism. In the tool change part, upper tools can be exchanged automatically for the inserting of various components. The control part consists of motor drivers, PLCs and power supply.

• 한국멀티미디어학회논문지
• /
• 제12권11호
• /
• pp.1557-1562
• /
• 2009

단조프레스기의 유압실에서 배관의 연결부위의 손강으로 인한 누유는 인명피해와 기계 파손의 위험성이 있어 이를 조기에 발견하여 예방하는 시스템이 필요하다. 본 논문에서는 원격지에서 회전형 카메라를 이용하여 유압유의 누유여부를 자동 인식하는 시스템을 구현하였다. 구현한 시스템은 라벨링 과정에서 객체영역을 나타내는 경계사각형을 구하고 경계사각형의 높이와 폭에 대한 비율, 누유형상의 원형도를 이용하여, 올바른 누유영역을 추출하였다. 또한 잡음제거와 영상의 이동과 회전에 대한 보정을 전처리 과정으로 수행한다. 실험을 통하여 제안한 시스템이 여러 가지 조명 환경에서도 누유영역을 정확하게 찾아내는 것을 확인하였다.

• 한국콘텐츠학회:학술대회논문집
• /
• 한국콘텐츠학회 2009년도 춘계 종합학술대회 논문집
• /
• pp.35-39
• /
• 2009

단조프레스기의 유압실에서 배관의 연결부위의 손상으로 인한 누유는 인명피해와 기계 파손의 위험성이 있어 이를 조기에 발견하여 예방하는 시스템이 필요하다. 본 논문에서는 원격지에서 회전형 카메라를 이용하여 유압유의 누유여부를 자동 인식하는 시스템을 구현 하였다. 구현한 시스템은 레이블링 과정에서 후보누유영역을 나타내는 최소경계사각형(MBR)을 구하고 MBR의 넓이와 높이 및 MBR의 면적과 후보 누유 영역의 면적비를 이용하여, 올바른 누유영역을 추출하였다. 실험을 통하여 제안한 시스템이 여러 가지 조명 환경에서도 누유영역을 정확하게 찾아내는 것을 확인하였다.

• 한국정밀공학회지
• /
• 제25권2호
• /
• pp.49-56
• /
• 2008

In order to reduce energy consumption, secondary controlled system has been applied to many types of equipments. In lifting equipments or press machines using hydraulic cylinder, a hydraulic transformer is used as a control component instead of a valve for motion control and a component for recovering potential energy of load. The transformer is a combination of a variable displacement pump/motor as a secondary controlled element and a fixed displacement pump/motor. In this paper the effect of transformer is studied. Multiple closed loop controllers with displacement feedback of variable pump/motor, speed feedback and position feedback of cylinder are used. The efficiency and energy consumption when cylinder is driven up and down is calculated by simulation. Simulation results show that considerable energy saving is achieved by choosing load ratio, circuit type and supply pressure.

• Earthquakes and Structures
• /
• 제15권2호
• /
• pp.215-225
• /
• 2018

To reach a better foundation treatment project, an optimized analysis of composite foundation was studied in the field of hydraulic engineering. Its unique characteristics in hydraulic engineering were concluded. And, the overall and detailed analysis of the composite foundation model established was carried out. The index parameters of the vertical reinforced rigid pile composite foundation were formulated. Further, considering the unique role of cushion in hydraulic engineering, its penetration and regularity were analyzed. Then, comparative and optimized analyses of cushion multistage physical dimensions and multistage material characteristics were established. The parameters of the piles distance were optimized and the multilevel scientific and reasonable parameters information was obtained. Based on the information of these parameters, the practical application was verified. It effectively supported the effective application of vertical reinforcement rigid pile composite foundation in hydraulic engineering. The service mechanism of composite foundation was fully analyzed.