• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1755-1759
• /
• 2003

The hydraulic excavator has been a popular research object for automation because of its multi-workings and economic efficiency. The objective of this paper is to design each components and to construct boom, arm, bucket circuit. These models modeled with AMESim show us change of variables and behavior of excavator. Simulation model will be used for simulator of excavator.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권2호
• /
• pp.241-247
• /
• 1998

The hydraulic coupling is a kind of power transmission device combined with pump turbine and casing as its main parts. The purpose of this research is to construct an experimental test set-up and to establish an available soft ware for th characteristics of two domestically developed hydraulic couplings. The test item is torgue rpm. and slip and or efficiency characteristic in accordance with variation of oil quantity. in this case the oil quantity was varied 55%, 67% and 77% of the inside capacity of hydraulic copuling.

• 한국환경보건학회지
• /
• 제27권3호
• /
• pp.11-20
• /
• 2001

An anaerobic sludge-aerobic fixed-bed biofilm(packed with ceramic support carrier of 1 inch size) reactor system was built up to treat textile wastewater. The efficiency of reactor system was examined by determining the effects of textile wastewater ratio(from 25% to 100% at HRT 24 h). The influent range of SCOD concentration and color were 1,036~1,357 mg/L, and 1,487~1,853 degree, respectively. When textile wastewater ratio was 100% and hydraulic retention time was 24 hours, SCOD removal efficiency by the anaerobic stage were 39.2% 100% and hydraulic retention time was 24 hours, SCOD removal efficiency by the anaerobic stage were 39.2% and the removal efficiency of the whole system were 75.8%. Color removal efficiency by the anaerobic stage were 45.4%(soluble color), and the removal efficiency of the whole system were 70.2%. In the A/A reactor system, the aerobic stage played an important role in removing both color and COD as well as anaerobic stage.

• International Journal of Fluid Machinery and Systems
• /
• 제2권4호
• /
• pp.392-399
• /
• 2009

The paper concerns the description of the step by step development process of the new fixed blade runner called "Mixer" suitable for the uprating of the Francis turbines units installed at the older low head hydropower plants. In the paper the details of hydraulic and mechanical design are presented. Since the rotational speed of the new runner is significantly higher then the rotational speed of the original Francis one, the direct coupling of the turbine to the generator can be applied. The maximum efficiency at prescribed operational point was reached by the geometry optimization of two most important components. In the first step the optimization of the draft tube geometry was carried out. The condition for the draft tube geometry optimization was to design the new geometry of the draft tube within the original bad draft tube shape without any extensive civil works. The runner blade geometry optimization was carried out on the runner coupled with the draft tube domain. The blade geometry of the runner was optimized using automatic direct search optimization procedure. The method used for the objective function minimum search is a kind of the Nelder-Mead simplex method. The objective function concerns efficiency, required net head and cavitation features. After successful hydraulic design the modal and stress analysis was carried out on the prototype scale runner. The static pressure distribution from flow simulation was used as a load condition. The modal analysis in air and in water was carried out and the results were compared. The final runner was manufactured in model scale and it is going to be tested in hydraulic laboratory. Since the turbine with the fixed blade runner does not allow double regulation like in case of full Kaplan turbine, it can be profitably used mainly at power plants with smaller changes of operational conditions or in case with more units installed. The advantages are simple manufacturing, installation and therefore lower expenses and short delivery time for turbine uprating.

• 해양환경안전학회지
• /
• 제28권1호
• /
• pp.168-174
• /
• 2022

월파된 파도를 이용한 파력발전시스템을 월파수류형 파력발전기 OWEC(Overtopping Wave Energy Converter)라고 한다. OWEC의 성능은 발전 시스템은 특성상 파도의 파고와 주기의 영향을 받는다. 파도는 해양에 따라 파고, 주기, 파도 방향 등의 특성이 다르고 이러한 파도의 다양한 특성 때문에 OWEC는 안정적인 전력을 생산하기 어렵다. 따라서 각 바다의 특성에 따른 OWEC의 적절한 형상에 관한 연구가 필요하다. 본 연구에서는 SPH(Smoothed Particle Hydrodynamics) 입자법을 사용하여 OWEC의 램프 설계가 hydraulic efficiency에 미치는 영향을 확인했다. 총 10개의 모델을 설계하였으며, 선택된 매개변수에 따라 램프의 설계 파라미터를 선택하고 사면의 형상을 변경하여 시뮬레이션을 수행하였다. 해석 결과로부터 구한 유량을 기초로 hydraulic efficiency를 산출하였다. 계산된 hydraulic efficiency를 바탕으로 각 변수가 사면의 형상에 따른 월파 성능에 미치는 영향을 확인하였다. 본 연구에서는 특정 해역에 따른 OWEC 램프의 적절한 형상에 대한 방향을 제시하였다.

• 드라이브 ㆍ 컨트롤
• /
• 제17권3호
• /
• pp.26-32
• /
• 2020

In modern society, the energy-saving problem of industrial vehicles is economically and environmentally critical. Energy savings using the potential energy of forklifts are one of the viable solutions to resolving this problem. The basic concept of this study is to operate the hydraulic motor and recharge the battery using the flow rate from the cylinder when loading heavy objects and lowering the fork. To save energy, the torque and rotational speed of the generator should be optimized according to the load and descent speed to increase efficiency. To this end, we propose a system that optimizes energy saving efficiency by controlling the swashplate angle of the variable hydraulic motor through the GA(Genetic-Algorithm). The results were verified by building and comparing fixed motor models and variable motor models using the AMEsim. The results of the study show that the proposed optimized swashplate angle increases the energy saving efficiency by approximately 6%-8%, depending on the working conditions.

• 한국안전학회지
• /
• 제33권5호
• /
• pp.134-140
• /
• 2018

Scour in the downstream of hydraulic structures such as apron induces to collapse due to abruptly increasing rainfall and discharge in streams and reaches. This is because the forcible jet from overflowing is not sufficiently dissipated by existing energy dissipators, and it continues to sweep the bed materials during flood events. In this study, a second stilling basin was proposed as a countermeasure and the energy dissipation efficiency of this structure was analyzed using 3D-dimensional numerical analysis. First, results from previous research and hydraulic tests were used to verify the accuracy of the numerical model. It showed that the second stilling basin played a definite role in reducing the bottom velocity, comparing with diminishing the energy dissipation when numerical tests were conducted under scaled field conditions in Korea. This means that the second stilling basin can be a countermeasure against scour in downstream. If more efficiency analysis of the second stilling basin would be performed in terms of energy dissipator for various types of hydraulic jump, it would be an alternative solution to scouring issues.

• 한국자동차공학회논문집
• /
• 제14권1호
• /
• pp.39-47
• /
• 2006

Recent trend in pursuit of high performance and effectiveness for automotive cooling system has changed the application of material for impeller of automotive water pump from metal to high ability engineering resin, which can achieve optimization of design of impeller geometry and realize lightweight high efficiency water pump. Closed type water pump improves hydraulic loss of fluid through the clearance between volute casing and impeller compared with that of the existing open type water pump(Although closed type is heavier than open type for the same size and same material, adoption of plastics can solve the problem.). In the present study, the characteristics of hydraulic performance of closed type water pump were investigated with respect to the angle between shroud and hub of impeller and the shape of discharge port of volute casing. Performance tests were carried out for 4 cases, that is, for 2 impellers and 2 casings. The modification of shape of only discharge port can enhance the hydraulic performance by 10 percent and the pump efficiency by 4-6 percent.

• Geomechanics and Engineering
• /
• 제25권1호
• /
• pp.31-40
• /
• 2021

Injection grouting is one of the most common ground improvement practice to increase the strength and reduce the hydraulic conductivity of soils. Owing to the environmental concerns of conventional grout materials, such as cement-based or silicate-based materials, bio-inspired biogeotechnical approaches are considered to be new sustainable and environmentally friendly ground improvement methods. Biopolymers, which are excretory products from living organisms, have been shown to significantly reduce the hydraulic conductivity via pore-clogging and increase the strength of soils. To study the practical application of biopolymers for seepage and ground water control, in this study, we explored the injection capabilities of biopolymer-based grout materials in both linear aperture and particulate media (i.e., sand and glassbeads) considering different injection pressures, biopolymer concentrations, and flow channel geometries. The hydraulic conductivity control of a biopolymer-based grout material was evaluated after injection into sandy soil under confined boundary conditions. The results showed that the performance of xanthan gum injection was mainly affected by the injection pressure and pore geometry (e.g., porosity) inside the soil. Additionally, with an increase in the xanthan gum concentration, the injection efficiency diminished while the hydraulic conductivity reduction efficiency enhanced significantly. The results of this study provide the potential capabilities of injection grouting to be performed with biopolymer-based materials for field application.

• 드라이브 ㆍ 컨트롤
• /
• 제14권3호
• /
• pp.50-57
• /
• 2017

Recently, methods of verification for electro-hydraulic servo controllers are various and the required number of testing controllers is continuously increasing in some specific systems. In this study, a PCB-based electronic simulator of hydraulic actuators is designed and developed to simplify test set-up for controllers and to facilitate alteration for characteristics of the simulator. Several features to reduce required time and manpower for verifying controllers are described. Especially, the simulator is considerably efficient to examine some controllers for different hydraulic actuators in a test. Response characteristics of the simulator are compared with those of real actuators to demonstrate validity of this method. Results reveal utilizing the designed simulator for inspecting controllers is equally effective as using hydraulic actuators.