• 한국정보전자통신기술학회논문지
• /
• 제12권5호
• /
• pp.499-506
• /
• 2019

본 논문은 SiC Hybrid module를 적용한 7kW 인버터의 동작 안정성에 관한 것으로 손실 방정식과 시뮬레이션 결과를 비교하여 시뮬레이션 결과의 유효성을 검증하였으며, 시뮬레이션을 통해 Si module과 SiC Hybrid module의 스위치 손실과 다이오드 손실을 비교하였다. 손실 방정식 계산을 통하여 SiC Hybrid module의 도통 손실은 168W, 스위칭 손실은 9.3W, 다이오드 손실은 10.5nW의 결과를 나타내었으며, 시뮬레이션 결과와 비교하였을 때 유사한 값을 나타내었다. 이를 바탕으로 Si module과 SiC Hybrid module의 시뮬레이션 결과 값 비교 결과, Si module의 총 소자 손실값은 246.2W, SiC Hybrid module의 총 소자 손실 값은 189.9W를 나타내었으며, 손실 차이 값은 56.3W로써 약 0.8W의 효율 차이를 보였다. 이로 인하여 SiC SBD의 Reverse recovery 특성을 검증하였다. 또한 고온 포화상태에서 SiC Hybrid module 및 Si module의 안정성을 확인하기 위하여 온도 포화 테스트를 진행하였으며, Si module의 경우, 출력전력 4kW에서 동작을 멈추었고, SiC Hybrid module은 7kW까지 동작을 확인하였다. 이를 바탕으로, 효율 그래프와 온도 그래프를 제시하였으며, Si module은 4kW까지, SiC Hybrid module은 7kW까지 그래프로 나타내었다.

• Journal of Power Electronics
• /
• 제13권4호
• /
• pp.584-591
• /
• 2013

In this paper, a hybrid booster power module with Si IGBT and Silicon Carbide (SiC) Schottky Barrier Diode (SBDs) is presented. The switching characteristics of the hybrid booster module are compared with commercial Silicon IGBT/Si PIN diode based modules. We applied the booster power module into a non-isolated on board vehicle charger with a simple buck-booster topology. The performances of the on-vehicle charger are analyzed and measured with different power modules. The test data is measured in the same system, at the same points of operation, using the conventional Si and hybrid Si/SiC power modules. The measured power conversion efficiency of the proposed on-vehicle charger is 96.4 % with the SiC SBD based hybrid booster module. The conversion efficiency gain of 1.4 % is realizable by replacing the Si-based booster module with the Si IGBT/SiC SBD hybrid boost module in the 6.6 kW on-vehicle chargers.

• 한국전기전자재료학회논문지
• /
• 제28권7호
• /
• pp.473-479
• /
• 2015

Hybrid supercapacitors with high power density and long cycle life are widely used for emergency power source of LED emergency luminaires. In this paper, we designed and fabricated a hybrid capacitor cell and a module for the LED emergency luminaires. Using hybrid supercapacitor cells (1,000 F, 2.8 V), we designed a module in a 10-year warranty considering aging and ESR. Considering the ESR and efficiency has been designed to module with 1,000 F 5.6 V design results in 2 series and 2 parallel combination. Module was used to confirm that the operation 77.5 minutes at room temperature, discharge LED emergency luminaires with 2 W. As a LED emergency luminaires of emergency power supply that we can support more than 10 years of life was confirmed the applicability of hybrid supercapacitor.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.2719-2724
• /
• 2003

In this paper, we deal with the kinematic and dynamic modeling of hybrid robotic systems that are constructed by combination of parallel and serial modules or series of parallel modules. Previously, open-tree structure has been employed for dynamic modeling of hybrid robotic systems. Though this method is generally used, however, it requires expensive computation as the size of the system increases. Therefore, we propose an efficient dynamic modeling methodology for hybrid robotic systems. Initially, the dynamic model for the proximal module is obtained with respect to the independent joint coordinates. Then, in order to represent the operational dynamics of the proximal module, we model virtual joints attached at the top platform of the proximal module. The dynamic motion of the next module exerts dynamic forces to the virtual joints, which in fact is equivalent to the reaction forces exerted on the platform of the lower module by the dynamics of the upper module. Then, the dynamic forces at the virtual joints are distributed to the independent joints of the proximal module. For multiple modules, this scheme can be constructed as a recursive dynamic formulation, which results in reduction of the complexness of the open-tree structure method for modeling of hybrid robotic systems. Simulation for inverse dynamics is performed to validate the proposed modeling algorithm.

• 전기학회논문지
• /
• 제67권7호
• /
• pp.854-859
• /
• 2018

This paper describes the characteristics of a hybrid supercapacitor module for power quality stabilization. Hybrid supercapacitor is an promising energy storage device that positioned between conventional EDLC and Li-ion battery. A cylindrical 7500F hybrid supercapacitor ($60{\times}138mm$) was assembled by using the $Li_4Ti_5O_{12}$ electrode as an anode and activated carbon as a cathode. Considering the ESR and efficiency has been designed to module with 41.6F 480V design results in 180 series combination. In order to determine the characteristics of the hybrid supercapacitor module for power system, hybrid supercapacitor cells were connected in series with active balancing circuit. As a result of measuring the 50kw UPS, it was discharged at the current of 104A~143A during the discharge in the voltage range of 350V~480V, and the compensation time at discharge was measured to be about 30s. These results can be used to stabilization of power quality by applying hybrid supercapacitor module.

• Composites Research
• /
• 제32권1호
• /
• pp.13-20
• /
• 2019

본 연구에서는 전기 자동차의 주요 부품 중 하나인, Battery Module의 품질 Issue 및 부품특성 개선을 위해 복합재료를 사용하여 구조보강 하였으며, 단일소재의 단점을 극복할 수 있는 Hybrid 개념의 기구 구조 최적화를 수행하고 성능을 비교하였다. 이를 위해 고전 적층 판 이론(Classical Laminated Plate Theory, CLPT)에 따른 복합재료 주요 설계 변수 도출 및 복합재료 물성 예측 알고리즘에 대해 연구하였으며, 설계된 복합재료의 기계적 물성을 바탕으로 유한요소해석(FEM)을 통해 Battery Module의 성능을 검증하였다. 이를 통해 자동차 Battery 부품의 안정성 및 경량화 등의 부품 특성 개선 여부를 확인할 수 있었다. 최종적으로 검증결과에 따르면 Selective Composite Patch로 보강된 Hybrid Battery Module은 기존 Al Battery Module에 비해 30%의 중량 감소 및 제품 두께 32.5%를 줄일 수 있고, 충격 성능 유지 등 Hybrid 구조의 장점을 입증하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년 학술대회 논문집 정보 및 제어부문
• /
• pp.388-390
• /
• 2006

This paper presents a hybrid SoC design for phase detection of single tone signal. The designed hybrid SoC is composed of three functional blocks, i.e., an analog to digital converter module, a phase detection module and a controller module. A design of the controller module is based on a 16-bit RISC architecture. An I/O interface and an LCD control interface for transmission and display of phase measurement values are included in the design of the controller module. A design of the phase detector is based on a recursive sliding-DFT. The recursive architecture effectively reduces the gate numbers required in the implementation of the module. The ADC module includes a single-bit second-order sigma-delta modulator and a digital decimation filter. The decimation filter is designed to give 98dB of SNR for the ADC. The effective resolution of the ADC is enhanced to 98dB of SNR by the incorporation of a pre FIR filter, a 2-stage cascaded integrator- comb(CIC) filter and a 30-tab FIR filter in the decimation. The hybrid SoC is verified in FPGA and implemented in 0.35 CMOS Technology.

• 반도체디스플레이기술학회지
• /
• 제21권1호
• /
• pp.142-147
• /
• 2022

After introducing Hybrid Bonding technology into image sensors using stacked sensors and image processors, large quantity production became possible. As a result, it is currently used in most of the CMOS image market in smartphones and other image-based devices worldwide, and almost all stacked CIS manufacturing sites have focused on miniaturization using hybrid bonding. In this study, an upper wafer handling module for Wafer to Wafer Hybrid Bonding developed to increase the alignment and precision between wafers when wafer bonding. The module was divided two parts to reduce error of both the alignment and degree of precision during wafer bonding. Wafer handling module developed both new Tip/Tilt system controlling θx,θy of upper wafer and striker to push upper wafer. Based on this, it was confirmed through the stability evaluation that the upper wafer handling module can be controlled without any problem during W2W hybrid bonding.

• 산업공학
• /
• 제17권spc호
• /
• pp.52-61
• /
• 2004

During the past decades automated storage/retrieval (AS/R) systems have been dominantly implemented in most industrial fields due to their handling efficiency and high utilization of storage space. Such AS/R systems consist of several modules each of which contains two racks and a S/R machine. This paper proposes a design of the hybrid AS/R module which can be adopted without too much initial expenditure by most of small-and-medium sized companies. The hybrid module consists of an AS/R module on the upper floor and a traditional warehouse module on the lower floor. For the AS/R module, analytical expressions of the expected travel times for the S/R machine and the elevator per operation are derived. The expected travel times represent the performance of the module and thus can be used for its economic design.

• 전기학회논문지
• /
• 제65권4호
• /
• pp.617-621
• /
• 2016

In addition to the energy storage facilities based on high power technologies, Electric double layer capacitors(EDLC) are today's candidate for power quality stabilization. However, its low energy density is often inhibiting factor for application of electric power industry. Hybrid supercapacitor is an promising energy storage device that positioned between conventional EDLC and Li-ion battery. This paper describes the preparation and characteristics of a hybrid supercapacitor and module for power quality stabilization. A cylindrical 3200F hybrid supercapacitor ($60{\times}74.5mm$) was assembled by using the $Li_4Ti_5O_{12}$ electrode as an anode and activated carbon as a cathode. It shows 2.5 times higher energy density than conventional EDLC with the same volume. In order to determine the characteristics of the hybrid supercapacitor Module for uninterruptible power supply (UPS), hybrid supercapacitor cells were connected in series with active balancing circuit. At even the high current density of 14A(10C), Module prepared by 18 cells showed the capacitance of 170F at 30~50V, suggesting the applicability for UPS.