• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.294-299
• /
• 2004

An assessment of a novel laser-electric hybrid propulsion system was conducted, in which a laser-induced plasma was induced through laser beam irradiation onto a solid target and accelerated by electrical means instead of direct acceleration only by using a laser beam. A fundamental study of newly developed rectangular laser-assisted pulsed-plasma thruster (PPT) was conducted. On discharge characteristics and thrust performances with increased peak current compared to our previous study to increase effects of electromagnetic forces on plasma acceleration. Maximum peak current increased for our early study by increasing electromagnetic effects in a laser assisted PPT. At 8.65 J discharge energy, the maximum current reached about 8000 A. Plasma behaviors emitted from a thruster in various cases were observed with an ICCD camera. It was shown that the plasma behaviors were almost identical between low and high voltage cases in initial several hundred nanoseconds, however, plasma emission with longer duration was observed in higher voltage cases. Canted current sheet structures were also observed in the higher voltage cases using a larger capacitor. With a newly developed torsion-balance type thrust stand, thrust performances of laser assisted PPT could be estimated. The impulse bit and specific impulse linearly increased. On the other hand, coupling coefficient and the thrust efficiency did not increase linearly. The coupling coefficient decreased with energy showing maximum value (20.8 ？Nsec/J) at 0 J, or in a pure laser ablation cases. Thrust efficiency first decreased with energy from 0 to 1.4 J and then increased linearly with energy from 1.4 J to 8.6 J. At 8.65 J operation, impulse bit of 38.1 ？Nsec, specific impulse of 3791 sec, thrust efficiency of 8 %, and coupling coefficient of 4.3 ？Nsec/J were obtained.

• Korean Journal of Optics and Photonics
• /
• v.31 no.6
• /
• pp.281-289
• /
• 2020

This paper reports a slim mobile lens design using a hybrid refractive/diffractive optical element. Conventionally a wide field of view (FOV) camera-lens design adopts a retrofocus type having a negative (-) lens at the forefront, so that it improves in imaging performance over the wide FOV, but with the sacrifice of longer total track length (TTL). However, we chose a telephoto type as a baseline design layout having a positive (+) lens at the forefront, to achieving slimness, based on the specification analysis of 23 reported optical designs. Following preliminary optimization of a baseline design and aberration analysis based on Zernike-polynomial decomposition, we applied a hybrid refractive/diffractive element to effectively reduce the residual chromatic spherical aberration. The optimized optical design consists of 6 optical elements, including one hybrid element. It results in a very slim telephoto ratio of 1.7, having an f-number of 2.0, FOV of 90°, effective focal length of 2.23 mm, and TTL of 3.7 mm. Compared to a comparable conventional lens design with no hybrid elements, the hybrid design improved the value of the modulation transfer function (MTF) at a spatial frequency of 180 cycles/mm from 63% to 71-73% at zero field (0 F), and about 2-3% at 0.5, 0.7, and 0.9 fields. It was also found that a design with a hybrid lens with only two diffraction zones at the stop achieved the same performance improvement.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.22 no.1
• /
• pp.130-135
• /
• 2014

FOD(Foreign Object Debris) has the potential threat to damage aircraft during critical phases of take-off and landing roll with some objects including metal on the runway. FOD can be found anywhere on an airport's air operation areas such as runway, taxiway and apron. It can lead to catastrophic loss of life and airframe, and increased maintenance and operating costs. In this paper, we defined FOD and surveyed its riskiness and necessity of automatic FOD detection system. We compared the requirements of the environment in Korea to the FAA advisory circular. Also we analyzed operation methods of FOD detection systems already installed at some airports. Based on the surveys mentioned above, we propose hybrid type of FOD detection system considering the environment in Korea which uses millimeter wave radar, optical camera and thermal imaging camera to detect FOD efficiently. In management approach, fixed type of the system should be installed for real-time monitoring, and mobile type of the system can be used additionally.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.413-413
• /
• 2013

대면적 터치패널은 현재까지 저항막 방식, 적외선, Camera 방식을 주로 사용하고 있다. 저항막 방식의 Sensitivity, 높은 가격, 적외선 방식의 경우 빛의 간섭에 의한 오동작이 일어날 수 있는 문제를 가지고 있다. 최근의 Mobile용 터치스크린은 정전용량 방식의 터치기술 채택으로 저항막, 적외선, Camera 방식의 모든 단점을 해소할 수 있으나 터치 스크린 면적이 커지게 되면서 요구저항을 맞출 수 없는 문제로 현재 크기의 제한적이다. 본 연구에서는 완전일체형 터치(G2 Touch Hybrid) 방식의 ITO 터치필름을 사용하지 않고, 강화유리 기판을 사용하여 저(低)저항, 고(高)투과, 대형화(15 Inch), 경량화를 고려한 Zero-gap ITO를 코팅한 커버 유리용 투명전극에 대하여 전기적, 광학적, 구조적, 표면적 특성을 분석하였다. ITO 박막의 두께를 최소화하여 패턴 인비저블의 특성을 갖는 것이 필요로 하는데, 이는 ITO박막 패턴후에 패턴이 보이지 않게 하기 위해서이며, 이러한 시장의 요구를 충족하기 위해 RF/DC 고자력 Magnetron Sputtering System을 사용하여 면저항 $80{\Omega}$/${\Box}$, 표면특성 Rp-v 2.1 nm, 최고 광투과율 90.5%@550 nm, 반사율 차이 0.5 이하의 특성을 확인하였다. 또한, 저항 경시변화를 줄이기 위해서 Sheath heater를 이용한 진공코팅 중 발생되는 BM Ink out-gassing을 줄여 out-gassing에 의한 박막 손상을 줄일 수 있었으며 진공 성막중 결정성을 갖는 ITO 막을 형성시킬 수 있었다.

• Journal of the Korean Society of Safety
• /
• v.29 no.5
• /
• pp.15-21
• /
• 2014

The aim of this work is conduct the study on light weight and structural performance improvement of the composite wind power blade. GFRP (Glass Fiber Reinforced Plastic) pre-empted by CFRP(Carbon Fiber Reinforced Plastic), the major material of wind power blade, was identified the superiority of mechanical performance through the tensile and fatigue test. SENT(Single Edge Notched Tension) specimen fracture test was conducted on the specimen that laminated together 2 ply CFRP with 4 ply GFRP through DIC(Digital Image Correlation) analysis. The SENT specimen thickness and $a_0/W$ ratio is 1.45 mm and 0.2, respectively. The fracture test accomplished with displacement control with 0.1 mm/min at the room temperature. The experimental apparatus used for the fracture test consisted of a 50kN universal dynamic tester and CCD camera connected to a personal computer (PC), which was used to record images of the specimen surface. Following data acquisition, the images and load-displacements were transferred to the PC, on which the DIC software was implement. The experiment and DIC analysis results show that CFRP/GFRP laminated composite exhibits improvement of the strength, compared with that of the existing blade material. This study shows the result that the strength of CFRP rotor blade of wind turbine satisfies through the experimental and DIC method.

• Journal of Satellite, Information and Communications
• /
• v.10 no.1
• /
• pp.62-66
• /
• 2015

This paper introduces various applications and contents of digital signage, and analyzes conventional communication techniques to increase communication range. To realize digital signage in long distance, this paper proposes a hybrid modulation scheme and analyzes its performance. To verify its performance in real channel environment, we mapped symbols and experimented data transmission and reception with a visible light communication module with USRP. As a result, we confirmed a data receiving range and power of transmission and reception of the hybrid modulation mode. Also, we showed that the proposed modulation scheme has better performance of communication range and power efficiency than that of the conventional QAM technique.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.292-297
• /
• 2000

In this research, the dynamic photoelastic experimental hybrid method for bimaterial is introduced. Dynamic biaxial loading device is developed, its strain rate is 31.637 s-1 and its maximum impact load is 20 ton. Manufactured methods for model of the dynamic photoelastic experiment for bimaterial are suggested. They are bonding method(bonding material: AW106, PC-1) and molding method. In the bonding method, residual stress is not occurred in the manufactured bimaterial. Crack is propagated along the interface or sometimes deviated from the interface. While in the molding method, residual stress is occurred in the manufactured bimaterial. Crack is always deviated from the interface and propagated in the epoxy region(softer materila). In order to propagate with constant velocity along the interface of bimaterial with arbitrary stiffer material, edge crack should be located along the interface of the acute angle side of the softer material in the bimaterial.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.3
• /
• pp.835-854
• /
• 2012

In this paper, we propose a novel positioning system for indoor navigation which helps a user navigate easily to desired destinations in an unfamiliar indoor environment using his mobile phone. The system requires only the user's mobile phone with its basic equipped sensors such as a camera and a compass. The system tracks user's positions and orientations using a vision-based approach that utilizes $360^{\circ}$ panoramic images captured in the environment. To improve the robustness of the vision-based method, we exploit a digital compass that is widely installed on modern mobile phones. This hybrid solution outperforms existing mobile phone positioning methods by reducing the error of position estimation to around 0.7 meters. In addition, to enable the proposed system working independently on mobile phone without the requirement of additional hardware or external infrastructure, we employ a modified version of a fast and robust feature matching scheme using Histogrammed Intensity Patch. The experiments show that the proposed positioning system achieves good performance while running on a mobile phone with a responding time of around 1 second.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.17 no.7
• /
• pp.913-918
• /
• 2007

Human motion analysis is an important research subject in human-robot interaction (HRI). However, before analyzing the human motion, silhouette of human body should be extracted from sequential images obtained by CCD camera. The intelligent robot system requires more robust silhouette extraction method because it has internal vibration and low resolution. In this paper, we discuss the hybrid silhouette extraction method for detecting and tracking the human motion. The proposed method is to combine and optimize the temporal and spatial gradient information. Also, we propose some compensation methods so as not to miss silhouette information due to poor images. Finally, we have shown the effectiveness and feasibility of the proposed method through some experiments.

• Journal of Biosystems Engineering
• /
• v.26 no.1
• /
• pp.21-28
• /
• 2001

Major deficiencies of current automation scheme including various robots for bioproduction include the lack of task adaptability and real time processing, low job performance for diverse tasks, and the lack of robustness of take results, high system cost, failure of the credit from the operator, and so on. This paper proposed a scheme that could solve the current limitation of task abilities of conventional computer controlled automatic system. The proposed scheme is the man-machine hybrid automation via tele-operation which can handle various bioproduction processes. And it was classified into two categories. One category was the efficient task sharing between operator and CCM(computer controlled machine). The other was the efficient interface between operator and CCM. To realize the proposed concept, task of the object identification and extraction of 3D coordinate of an object was selected. 3D coordinate information was obtained from camera calibration using camera as a measurement device. Two stereo images were obtained by moving a camera certain distance in horizontal direction normal to focal axis and by acquiring two images at different locations. Transformation matrix for camera calibration was obtained via least square error approach using specified 6 known pairs of data points in 2D image and 3D world space. 3D world coordinate was obtained from two sets of image pixel coordinates of both camera images with calibrated transformation matrix. As an interface system between operator and CCM, a touch pad screen mounted on the monitor and remotely captured imaging system were used. Object indication was done by the operator’s finger touch to the captured image using the touch pad screen. A certain size of local image processing area was specified after the touch was made. And image processing was performed with the specified local area to extract desired features of the object. An MS Windows based interface software was developed using Visual C++6.0. The software was developed with four modules such as remote image acquisiton module, task command module, local image processing module and 3D coordinate extraction module. Proposed scheme shoed the feasibility of real time processing, robust and precise object identification, and adaptability of various job and environments though selected sample tasks.