• 대한기계학회논문집A
• /
• 제26권9호
• /
• pp.1842-1848
• /
• 2002

Although DLC coatings have good tribological properties, these are dependant on the deposition method, the property of contact surface, and test condition. Humidity, which has little influence on tribological behavior in macro scale, is an important factor of tribological behavior in small devices like MEMS. The objective of this study is to investigate the tribological behavior of DLC coatings with particular attention to their wettability at various humidities. DLC coatings were deposited on Si substrates and tested using a reciprocating friction tester against Si$_3$N$_4$balls at various humidities. The results showed that the tribological behavior of DLC coatings was dependant on relative humidity and wettablility of DLC coatings. Friction coefficient at high relative humidity was higher thar that at low relative humidity. The tungsten-containing DLC coatings had a good wear resistance at low relative humidity whereas DLC coatings derived from argon(Ar)+cesium(Cs) gases showed a good wear resistance at high relative humidity.

• 펄프종이기술
• /
• 제35권2호
• /
• pp.33-38
• /
• 2003

In order to design the high strength corrugated fiberboard containers for agricultural products that can be used for the cold chain system, a large number of individual boxes were placed in various humidity environments at two different temperature of 5 and $20^{\circ}C$. The results indicated that temperature changes do not effect on physical strength of corrugated fiberboard containers as much as humidity changes did. The main conclusion from this study was that compression strength of corrugated fiberboard containers dropped significantly at high humidity condition, but the rates varied depending on the number of walls, temperature, and perimeter of containers. The packaging designer must consider the corrugated fiberboard boxes are also greatly affected by dimensional variations such as the length versus width ratio. Based on this study, water-resistant board would not be necessary if the ambient relative humidity does not reach to a critical point, 85 percent in the cold chain system. However, the designer must count for the unexpected fluctuation of rotative humidity resulting in severe loss of the compression strength of corrugated fiberboard container.

• 한국추진공학회지
• /
• 제9권2호
• /
• pp.46-53
• /
• 2005

혼합형 고체 추진제의 온도 및 습도 가속노화 시험을 수행하여, 그 결과를 분석하였다 수명 평가를 위해서 온도 가속 노화 시험을 수행하였고, 산화제인 AP의 흡습성에 의해 추진제가 연화되는 특성을 분석하기 위해 상대습도 10, 30, $50\%$에서 습도 노화 시험을 수행하였다 온도 가속 노화 시험은 시편을 제작하여 시험하였고, 습도 시험은 실제 모터와 유사한 추진제 블록을 만들어 시험하였다. 온도 가속 노화 결과 $60^{\circ}C$에서 4개월 저장 결과가 $20^{\circ}C$에서 10년 저장한 결과로 예측되었다 HTPB 바인더를 사용한 혼합형 고체 추진제는 시간에 따라 경화되는 경향을 나타내었으며, 상대 습도 $50\%$까지는 습기의 영향이 크게 나타나지 않았다.

• International Journal of Industrial Entomology and Biomaterials
• /
• 제39권2호
• /
• pp.74-81
• /
• 2019

Freeze-dried 3^rd day of 5^th instar silkworm powder (FDSP) has been produced and consumed as functional food ingredient in Korea. Generally, FDSP is distributed in the dehumidification state. In this study, the effect of humid condition (30%, 50%, 70%, and 90% RH) on the quality characteristics of FDSP was examined. The color of FDSP, greenish yellow, becomes dark with the change of redness and yellowness. When FDSP is exposed for 4 h at 90% RH, the lightness was changed from 56 to 51, redness from -0.8 to 3.7, and yellowness from 26.5 to 21.6. The proximate composition of FDSP was not significantly changed except 90% RH condition. At that condition, moisture content (5.7%) was increased to 26.8% and crude fat (11.3%) decreased to 1.9% (3 wk 90% RH). Mineral content change during storage can be classified to 3 types; sulfur rapidly decreased, potassium mostly stable with some decreased with humidity, and sodium increased with high humid condition. Vitamins were not significantly affected. However, DNJ was abruptly decreased to 0.03 g/100g in humid condition.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.163-168
• /
• 2002

Through the developing measuring system of gas diffusivity, the experiments on carbon dioxide diffusivity in concrete carry out. From this, some important results was achieved. First, the times of reaching the steady state condition don't depend on the water/cement ratio with linearity. But, for the 0.42 w/c ratio the duration of the non-steady state condition is long. Second, in constant relative humidity, the diffusion coefficient shows linearity for the w/c ratio. Third, for the same w/c ratio, the influence of relative humidity on the diffusivity is very large. This shows the importance of the environmental condition for the carbonation. This study on $CO_2$ diffusivity in concrete is the first attempt within a country and will be important data.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.175-180
• /
• 2002

Regardless of the carbonation of concrete is one of the importants causes of corrosion of reinforing steel in concrete with the cloride attack and the frost damage, the investigacion about the carbonation of concrete is limited and each investigator experiments under different condition. In this paper, the effect of temperature, relative humidity, concentration of $CO_2$, type of specimen, etc., were investigated according to the accelerated carbonation test. The principal conclusions from this research were as follows: 1) The carbonation of concrete is higher in olden of, under environmental condition(temperature-relative humidity, concentration of $CO_2$, ) of 40-40-10＞40-50-10＞40-60-5＞20-60-5. 2) Under same environmental condition, the carbonation of concrete in $\Phi$10$\times$20cm cylinder specimen is 2-8% higher then 10$\times$10$\times$40cm specimen.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제18권1호
• /
• pp.8-19
• /
• 2018

Purpose: This study has developed the accelerated lifetime test method for smps for outdoor lighting LED through two factors of temperature and humidity. Methods: Acceleration condition was confirmed for each stress and model, and acceleration life test model was estimated according to acceleration condition. Results: As a result of confirming the accelerated life test model, in the case of humidity, acceleration was established only in the foreign products. Therefore, it is confirmed that the acceleration condition is insufficient. However, the estimated parameters for temperature are relatively constant. It is therefore suitable for power supply acceleration tests for outdoor lighting LEDs. Conclusion: The SMPS acceleration test for outdoor lighting LED can improve the availability of the product by developing an accelerated life test method that guarantees the reliability of the product.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.234-235
• /
• 2005

In this experiment study, to acquire elementary data for explaining to generate frost layer in the fin - tube evaporator. the experiment condition is to supply air on 0.3m/s, 0.6m/s, 0.9m/s and inlet air temperature is 15$^{circ}C$, 20$^{circ}C$, 25$^{circ}C$ , supplied air relative humidity is 70%, 80, 90%. And brine temperature in the copper tube was kept -15$^{circ}C$ because, generally cooling temperature range is constantly -15$^{circ}C$ in the heat exchanger for air conditioning system. in conclusion, through this experiment, we did compare with frost layer and frost thickness in each condition and examine these data

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 가을 학술논문 발표대회
• /
• pp.153-154
• /
• 2020

This study aims to find out the reason that tile adhesive(type III) for ceramic tile does not harden under some conditions especially high humidity even though long curing time. Bonding strength of adhesive between substrate and ceramic tile is evaluated depending on bonding conditions such as substrate kind(concrete, board), bonding material (tile adhesive, tile cement) and curing condition(humidity 50, 70%). Based on the results, this study aimed to establish the quality of tile adhesion strength under the relevant conditions.

• 한국의류학회지
• /
• 제29권7호
• /
• pp.1027-1036
• /
• 2005

Based on the correlation analysis result of preceding research, the biodegradabilities of cellulose fibers were closely related to the moisture regain of the samples, which reflects the hydrophilicity and internal structure of the fibers. In addition to this factor, it was expected that the biodegradation conditions influence the biodegradability of fibers. In this study, widely used cellulose fibers including cotton, rayon, and acetate were used. The biodegradabilities of cellulose fibers were measured by soilburial test, and then the degradation behaviors based on each condition were compared. Moreover, the effects of degradation conditions such as humidity of the soil were investigated. Changes in the internal structure of samples were also observed by X-ray analysis according to the soil burial time. It was shown that humidity of soil facilitated the degradation of cotton, rayon, and acetate fibers, showing higher degradation rate with higher humidity in soil. This effect was shown to be much greater in the fibers of high moisture regain such as cotton and rayon. In respect of microstructure change, crystallinities and their crystal size of fibers decreased remarkably in the soil of higher humidity. It was revealed that degradation of crystalline area was more dependent on the soil humidity than that of amorphous area.