• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.281-284
• /
• 2007

The effect of Ca addition on the microstructure evolution and deformation behavior of AZ31 magnesium alloy produced by hot extrusion was investigated. For this purpose, Ca was added into AZ31 melts to the level of 0.7 and 2.0 wt.% Ca. Then, AZ31 base alloy and Ca modified AZ31 alloys were extruded at $383^{\circ}C$. Ca added alloys showed finer grain size and increased hardness value rather than AZ31 base alloy. After isothermal hot compression, the shape of tested specimen exhibited a noticeable anisotropy due to the crystallographic texture effect. The ratio of major and minor axes of ovality was not directly related to test condition and Ca amount. Flow stress level increases with the increase of Ca addition at temperature below $300^{\circ}C$ because of fine microstructure. However, at high temperature and low strain rate region ($400^{\circ}C$ and $10^{-3}s^{-1}$), reverse tendency was observed since main deformation mechanism changes from dislocation slip to grain boundary sliding or diffusional process at high temperature.

• Journal of Mechanical Science and Technology
• /
• 제20권7호
• /
• pp.1002-1011
• /
• 2006

In this study, we describe the conventional hot pressing (CHP) of layered $Al-B_4C$ composites and their characterization. The matrix alloy Al-5 wt.%Cu was prepared from elemental powder mixtures. The metal and B4C powders were mixed to produce either $Al-Cu-10vol.%B_4C$ or $Al-Cu-30vol.%B_4C$ combinations. Then, these powder mixtures were stacked as layers in the hot pressing die to form a two-layered composite. Hot pressing was carried out under nitrogen atmosphere to produce $30\times40\times5mm$ specimens. Microstructural features and age hardening characteristics of composites were determined by specimens cut longitudinally. The flexural strength of both layered composites and their monolithic counterparts were investigated via three point bending tests. In the case of layered specimens of both $10vol.%B_4C$ and $30vol.%B_4C$ containing layers were loaded for three-point test. The results show that a homogeneous distribution of $B_4C$ particles in the matrix alloy which is free of pores, can be obtained by CHP method. The ageing behavior of the composites was found to be influenced by the reinforced materials, i.e. higher hardness values were reached in 8 hrs for the composites than that for the matrix alloy. Flexural strength test showed that two-layered composites exhibited improved damage tolerance depending on layer arrangement. Microstructural investigation of the fracture surfaces of the bending specimens was performed by means of scanning electron microscope (SEM). While layer with lower reinforcement content exhibited large plastic deformation under loading, the other with higher reinforcement content exhibited less plastic deformation.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2007년도 동계학술연구발표회 및 스핀트로닉스와 나노물리에관한 국제심포지움
• /
• pp.160-161
• /
• 2007

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2002년도 춘계연구발표회 논문개요집
• /
• pp.144-145
• /
• 2002

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2017년도 임시총회 및 하계학술연구발표회
• /
• pp.113-113
• /
• 2017

• 한국도로학회:학술대회논문집
• /
• 한국도로학회 2008년도 추계학술대회 논문집
• /
• pp.373-378
• /
• 2008

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권8호
• /
• pp.938-945
• /
• 2005

The microstructure evolution in hot forging process is composed of dynamic recrystallization during deformation as well as grain growth during dwell time. Therefore, the control of forging parameters such as strain, strain rate. temperature and holding time is important because the microstructure change in hot working affects the mechanical properties. Modeling equations are developed to represent the flow curve. grain size. recrystallized volume fraction and grain growth phenomena by various tests. The developed modeling equations were combined with thermo-viscoplastic finite element modeling to predict the microstructure change evolution during hot forging process. The large exhaust valve spindle (head diameter of 512mm) was simulated by closed die forging with hydraulic press and cooled in air after forging. The preform was heated to each 1080 and 1150$^{\circ}C$. Numerical calculation was performed by DEFORM-2D. a commercial finite element code. Heat transfer can be coupled with the deformation analysis in a non-isothermal deformation analysis. In order to obtain the fine and homogeneous microstructure and good mechanical properties in forging. the FEM would become a useful tool in the simulation of the microstructure development. In forging, appropriate temperature, strain and strain rate and rapid cooling are required to obtain the fine grain microstructure The optimal forging temperature and effective strain range of Nimonic 80A for large exhaust valve spindle are about 1080$\∼$l120$^{\circ}C$ and 150$\∼$200$\%$.

• 한국재료학회지
• /
• 제5권7호
• /
• pp.765-774
• /
• 1995

입자강화 알루미늄 복합재료의 고온거동을 조사하기위하여, 온도 623K~823K에서 $10^{-2}$ ~1.0 S$^{-1}$ 변형속도로 열간 압축 가공 시험을 행하여 복합재의 고온유동응력에 미치는 강화입자의 첨가량, 강화입자의 종류 및 크기와 변형속도 및 변형온도 등의 영향을 조사하였다. 강화입자의 체적분율이 증가함에 따라서 고온유동음력은 증가하였으나 항복점에서의 차이가 변형량이 증가되어도 그대로 유지되고 있었다. 변형속도 민감도(m)로 볼때 SiCp첨가된 복합재가 A1$_2$O$_3$p를 첨가한 복합재보다 비교적 균일하게 가공할 수 있음을 알 수 있었으며, 823K에서 최적변형속도는 0.1Sec$^{-1}$ 이었다. 변형에 필요한 활성화 에너지는 A6061기지금속이 290KJmole$^{-1}$, A6061-20vo1% SiCp = 327KJmo1e$^{-1}$, A6061-20vo1% $Al_2$O$_3$= 531KJmole$^{-1}$이었다. 이것은 알루미늄의 자기활성화에너지 138KJmo1e$^{-1}$보다 큰 값으로 A1$_2$O$_3$강화복합재료가 SiCp 강화 복합재료보다 열간가공이 어렵다는 것을 나타내는 것이다.

• Journal of Magnetics
• /
• 제7권4호
• /
• pp.138-142
• /
• 2002

Magnetic properties, microstructure and texture of NdFeB magnets fabricated by a modified hot working process from commercial melt-spun powders (Magnequench; MQPA, MQPB and MQPB＋) have been investigated. The hot-pressed isotropic magnet made from MQPA powder, which contains higher Nd content than that of MQPB or MQPB＋, shows higher coercivity. The magnet also shows homogenous and fine grains with higher coercivity for higher consolidation pressure. The hot-deformed MQPA magnet shows a strong anisotropy along the press direction with homogeneous platelet Nd$_2$Fe$_{14}$B grains of 50∼100nm in thickness and 200∼500nm in length. The hot-deformed MQPB＋ magnet, however, shows low remanence and low coercivity. The microstructure of the magnet consists of two areas; undeformed Nd$_2$Fe$_{14}$B grains and well-aligned but large grains with 3∼4 $\mu$m in length. Low Nd content attributes to the formation of the two different area.

• 소성∙가공
• /
• 제11권2호
• /
• pp.179-186
• /
• 2002

In the finite element analysis of metal forming Processes using general Lagrangian formulation, element nodes in the mesh move and elements are distorted as the material is deformed. The excessive degeneracy of mesh interrupts finite element analysis and thus increases the error of plastic deformation energy, In this study, a remeshing scheme using so-called mesh compression method is proposed to effectively analyze the flash which is generated usually in hot forging processes. In order to verify the effectiveness of the method, several examples are tested in two-dimensional and three-dimensional problems.