• Computers and Concrete
• /
• 제22권6호
• /
• pp.563-572
• /
• 2018

Uniaxial compressive strength test and uniaxial compression creep one were produced on four groups of twelve concrete specimens with different hole number by RLW-2000 rock triaxial rheology test system. The relationships between horizontal holes and instantaneous failure stress, the strain, and creep failure stress, the strain, and the relationships between stress level and instantaneous strain, creep strain were studied, and the relationship between horizontal holes and failure mode was determined. The results showed that: with horizontal hole number increasing, compressive strength of the specimens decreased whereas its peak strain increased, while both creep failure strength and its peak strain decreased. The relationships between horizontal holes and compressive strength of the specimens, the peak strain, were represented in quadratic polynomial, the relationships between horizontal holes and creep failure strength, the peak strain were represented in both linear and quadratic polynomial, respectively. Instantaneous strain decreased with stress level increasing, and the more holes in the blocks the less the damping of instantaneous strain were recorded. In the failure stress level, instantaneous strain reversally increased, creep strain showed three stages: decreasing, increasing, and sharp increasing; in same stress level, the less holes the less creep strain rate was recorded. The compressive-shear failure was produced along specimen diagonal line where the master surface of creep failure occurred, the more holes in a block, the higher chances of specimen failure and the more obvious master surface were.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 봄 학술발표회 논문집
• /
• pp.520-527
• /
• 2000

In the present study, the analytical approaches of vacuum consolidation with horizontal drains were proposed, For dissipating rapidly pore-water in hydraulic fills, vacuum consolidation method applied vacuum pressure in horizontal drains is developed. In the analytical approaches, the governing equation is based on two-dimensional finite strain consolidation theory and the boundary conditions of horizontal drains are considered in applying negative pore-water pressure occurred by vacuum pressure, Also, parametric studies to vacuum pressure and installation pattern of horizontal drains are carried out.

• 한국전기전자재료학회논문지
• /
• 제22권1호
• /
• pp.67-73
• /
• 2009

The stress-strain behavior and its effects on the crack initiation and growth of ITO film on PET substrate with a sheet resistance of 45 ohms/sq were investigated. Electrical resistance increased gradually at the strain of 0.7% in the elastic to plastic transition region of the stress strain curves. Numerous cracks were observed after 1% strain and the increase of the resistance can be linked to the cracking of ITO thin films. The onset strain for the increase of resistance increased with increasing strain rate, suggesting the crack initiation is dependent on the strain rate. Upon loading, the initial cracks perpendicular to the tensile axis were observed and propagated the whole sample width with increasing strain. The spacing between horizontal cracks is thought to be determined by the fracture strength and the interfacial strength between ITO and PET. The crack density increased with increasing strain. The spacing between horizontal cracks (perpendicular to the stress axis) increased with decreasing strain rate, The increase of crack density with decreasing strain rate can be attributed to the higher fraction of the plastic strain to the total strain at a given total strain. As the strain increased over 5% strain, cracks parallel to the stress axis were developed and increased in number with strain, accompanied by drastic increases of resistance.

• 전기학회논문지
• /
• 제60권3호
• /
• pp.594-599
• /
• 2011

A SAW strain sensor based on Shear Horizontal wave with an 92 MHz central frequency was developed. It consists of SAW sensor, PCB substrate and bonding material (Loctite 401). External force applied to PCB substrate bonded to a piezoelectric substrate induces strain at the substrate surface, which causes changes in the elastic constant and density of the substrate and hence the propagation velocity of the SAW. The change in the velocity of the SAW result in a frequency shift of the sensor and by measuring a frequency shift, we can extract the strain induced by the external force. The $41^{\circ}$ YX $LiNbO_3$ was used because it has a Leaky shear horizontal(SH) wave propagation mode and a high electromechanical coupling coefficient ($K^2$=17.2%). And to compare with Rayleigh wave mode, $128^{\circ}$ YX $LiNbO_3$ was used. And to make a stable and low insert loss, Split IDT structure was used. The obtained sensitivity and linearity of the SAW strain sensor in the case of Split IDT were measured to be 17.2 kHz / % and 0.99, respectively.

• Geomechanics and Engineering
• /
• 제23권3호
• /
• pp.289-300
• /
• 2020

With the rapid development of the distributed strain sensing (DSS) technology, the strain becomes an alternative monitoring parameter to analyze slope stability conditions. Previous studies reveal that the horizontal strain measurements can be used to evaluate the deformation pattern and failure mechanism of soil slopes, but they fail to consider various influential factors. Regarding the horizontal strain as a key parameter, this study aims to investigate the stability condition of a locally loaded slope by adopting the variable-controlling method and conducting a strength reduction finite element analysis. The strain distributions and factors of safety in different conditions, such as slope ratio, soil strength parameters and loading locations, are investigated. The results demonstrate that the soil strain distribution is closely related to the slope stability condition. As the slope ratio increases, more tensile strains accumulate in the slope mass under surcharge loading. The cohesion and the friction angle of soil have exponential relationships with the strain parameters. They also display close relationships with the factors of safety. With an increasing distance from the slope edge to the loading position, the transition from slope instability to ultimate bearing capacity failure can be illustrated from the strain perspective.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.370-375
• /
• 2005

This paper describes a systematic way of identifying the horizontal coefficient of consolidation for clayey soil under undrained condition and silty soil under partial drained condition by applying an optimization technique to the early part of dissipation data measured from the self-boring pressuremeter strain holding test. An analytical solution developed by Randolph & Wroth (1979) was implemented in normalized form to express the build-up and dissipation of excess pore pressures around a pressuremeter as a function of the rigidity index. Horizontal coefficient of consolidation was determined by minimizing the differences between theoretical and measured excess pore pressure curves using optimization technique. It was found that the proposed optimization technique can evaluate in-situ horizontal coefficient of consolidation rationally, which is similar with that obtained from the piezocone dissipation test. Furthermore, proposed method can evaluate appropriate coefficient of consolidation for soil under partially drained condition.

• 한국지반공학회논문집
• /
• 제20권3호
• /
• pp.151-159
• /
• 2004

본 논문에서는 자가굴착식 프레셔메터 시험의 변형을 유지시험(strain holding test)에서 관측된 소산시험 결과의 초기 소산경향으로부터 점성토 지반의 수평압밀계수를 추정하기 위한 최적화기법의 적용에 대하여 기술하였다. 프레셔메터의 확장으로 인한 초기 과잉간극수압의 분포는 Randolph. ＆ Wroth(1979)의 해석적 해(analytical solution)를 이용하여 지반의 강성지수의 함수로 모사되었으며 연속된 간극수압 소산과정까지 전과정이 모사되었다. 제안된 기법에서는 이를 소산곡선과 정규화 된 관측 소산곡선이 초기 50% 범위에서 소산경향이 가장 일치하도록 하는 수평압밀계수를 최적화기법을 이용하여 결정하였다. 제안된 기법을 김제와 양산에서 수행된 기존의 자가굴착식 프레셔메터 연구결과의 해석에 적용하였으며 제안된 방법으로 얻어진 수평압밀계수를 기존의 연구결과, 실내 및 원위치 시험결과와 비교하였다. 연구결과 제안된 방법은 피에조콘 소산시험과 매우 일관성있게 일치하는 수평압밀계수를 제공할 뿐 아니라 부분배수가 발생하는 지점에서도 간극수압 소산경향을 반영함으로 인해 보다 적절한 수평압밀계수를 결정할 수 있음을 알았다.

• 한국재료학회지
• /
• 제19권1호
• /
• pp.1-6
• /
• 2009

In this study, the stress-strain response and the cracking behaviors of ITO film on a PET substrate are investigated. The cracking behaviors of ITO thin films deposited on a thermoplastic semi-crystalline polymer developed for flexible display applications was investigated by means of tensile experiments equipped with an electrical measurement apparatus and an in-situ optical microscope. Electrical resistance increased gradually in the elastic-to-plastic transition region of the stress strain curves and cracks formed. Numerous cracks were found in this region, and the increase of the resistance was linked to the cracking of ITO thin films. Upon loading, the initial cracks perpendicular to the tensile axis were observed at about 1% of the total strain. They propagated to the entire sample width as the strain increased. The spacing between the horizontal cracks is thought to be determined by the fracture strength and the thickness of the ITO film as well as by the interfacial strength between the ITO and PET. The effect of the strain rate on the cracking behavior was also investigated. The crack density increased as the strain increased. The spacing between the horizontal cracks (perpendicular to the stress axis) increased as the strain rate decreased. The increase of the crack density as the strain rate decreased can be attributed to the higher fraction of the plastic strain to the total strain at a given total strain. The higher critical strain for the onset of the increase in the resistance and the crack initiation of the ITO/PET with a thinner ITO film (300 ohms/sq.) suggests a higher strength of the thinner ITO film.

• 반도체디스플레이기술학회지
• /
• 제14권2호
• /
• pp.23-27
• /
• 2015

In this paper, eco-friendly paper strain gauge was fabricated in the way of printing strain gauge on paper substrate, using PEDOT:PSS ink and inkjet printer technology. As a p-type conductive high polymer, PEDOT:PSS is known to be piezoresistive effect. I formed a strain gauge by connecting in parallel 5 lines of $60{\mu}m$ width printed with PEDOT:PSS. To minimize surrounding influence such as temperature, I formed wheat-stone bridge by combining 4 strain gauges (quarter-bridge strain gauge) which were made up of PEDOT:PSS 5 lines and measured. In quarter-bridge strain gauge, only two strain gauges, facing each other, arranged in strain and horizontal direction were deformed while the other two strain gauge of vertical direction were not. Therefore, quarter-bridge strain gauge showed the output of half bridge. The fabricated quarter-bridge strain gauge had output sensitivity of $105.6{\mu}V/V{\cdot}mm$ and its output linearity was relatively good.

• Korean Journal of Geomatics
• /
• 제3권2호
• /
• pp.141-148
• /
• 2004

This paper deals with the characteristics of strain pattern by using permanent GPS stations in Korea in terms of seismic activity and tectonics. Fourteen GPS stations involved in precise baseline vector solution and horizontal strain components were calculated using the differences of mean baseline from ten deily solutions during the time span of three years. The mean rate of maximum shear strain if 0.12 $\mu$/yr. The mean direction of principal axes of the compression is about $85^{\circ}$ N.