• Journal of the Korean Wood Science and Technology
• /
• 제18권3호
• /
• pp.42-52
• /
• 1990

In this study, thick 24mm glulams were composed of thick. 3, 4, 6, 8mm Larch laminas to study that the theoretical analysis and the experimental analysis regarding the location of neutral axis of the glulams were compared, and to study on the effect of location of neutral axis on mechanical properties of glulam. The variation of location of neutral axis after proportional limit(or elastical limit) was studied to offer basic data to make the better composition method of glulam. The result obtained can be summarized as follows: 1. The theoretical neutral axis was 0.547 in solid wood, and also 0.547 in glulams because glulams were composed of only Larch laminas. 2. In solid wood, the deviation of the theoretical and the experimental neutral axis location was 0.1%, But in glulams, the deviation from-12.2% to + 7.8% showed nonuniform pattern but no large deviation. Because laminas was only of Larch and so the mechanical properties of laminas were monotonous. 3. The neutral axis exerted no influance on the elasticity of glulam, which meaned that the maximum shear strength in the neutral axis showed no influance on elasticity limit. 4. The only minutely lower elasticities of glulam than that of solid wood were shown. This was because of influance of glue lines of glulam on the elasticlties. 5. The failure type of glulam was wholly simple tension failure and the horizontal shear failure near neutral axis was not taken place, which was that glue line was complete in bonding and the strength of the lamina was not various but uniform. 6. The ratio of tension strain($^{\varepsilon}t$) I compression strain($^{\varepsilon}c$) initially showed uniform level After the elasticity limit. the ratio was increased with the flow of time and so the tension strain was more increased than compression strain. So this proved tension lamination technique, which is that the mechanical properties of glulam could be improved, if the lamina of more superior strength would he added on the bottom side of the glulam.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1607-1614
• /
• 2011

As the connection between spread footing and pile is very important structural connection, it acts as the inter-loading medium to transfer the rail loads applied by superstructure to ground through the body pile of foundation. The experimental study is the method how to reinforce the pile cap between steel pile and footing utilizing perfobond plate with protruding keys. It were experimented on the compression punching tests and bending moment tests against the vertical loading and horizontal loadings acting on head of steel tube pipe. As a result, the tension capacity of the perfobond plate exhibited the superior performance due to the interlocking or dowel effects by the sheared keys of perfobond plate, and there were showing the sufficient strength and ductile capacity against the bending moment of horizontal loading tests. Therefore, it is judged that "the embedded method of perfobond plate in pile cap and footing" which is utilizing the shear connection of perfobond plate with protruding keys has a sufficient structural stability enough to be replaced with the current specification of reinforced method of pile cap with vertically deformed rebar against the vertical compression loads and bending moments that are able to occur in the combination structure of steel pile and the footing foundation.

• Structural Engineering and Mechanics
• /
• 제35권3호
• /
• pp.335-348
• /
• 2010

Cutouts are often provided in structural and aircraft components for ventilation, for access, inspection, electric lines and fuel lines or sometimes to lighten the structure. This paper addresses the effects of cutout shape (i.e., circular, square, diamond, elliptical-vertical and elliptical-horizontal) and size on buckling and postbuckling response of quasi-isotropic (i.e., $(+45/-45/0/90)_{2s}$) composite laminate under uni-axial compression. The finite element method is used to carry out the investigation. The formulation is based on first order shear deformation theory and von Karman's assumptions are used to incorporate geometric nonlinearity. The 3-D Tsai-Hill criterion is used to predict the failure of a lamina while the onset of delamination is predicted by the interlaminar failure criterion. It is observed that for the smaller size cutout area there is no significant effect of cutout shape on load-deflection response of the laminate. It is also concluded that the cutout size has substantial influence on the buckling and postbuckling response of the laminate with elliptical-horizontal cutout, while this effect is observed to be the least in case of laminate with elliptical-vertical cutout.

• 대한토목학회논문집
• /
• 제34권4호
• /
• pp.1081-1094
• /
• 2014

스트럿-타이 모델 방법은 철근콘크리트 코벨의 극한강도 해석 및 설계에 매우 효과적이다. 그러나 스트럿-타이 모델 방법을 이용한 철근콘크리트 코벨의 정확한 해석 및 안전한 설계를 위해서는 스트럿의 유효강도를 정확하게 결정하여야 한다. 이 연구에서는 여러 연구문헌에서 제안된 철근콘크리트 코벨의 대표적인 세 종류의 스트럿-타이 모델을 활용하기 위하여 철근콘크리트 코벨의 기하학적 형상, 수직 및 수평 하중의 조합 비, 그리고 휨철근 및 수평전단철근 비 등 주요 설계변수들의 영향을 정확하게 반영할 수 있는 스트럿 유효강도 식을 개발, 제안하였다. 현행 여러 설계기준서의 스트럿 유효강도 식과 이 연구에서 제안한 유효강도 식을 이용하여 파괴실험이 수행된 243개 철근콘크리트 코벨의 극한강도를 평가하였으며, 그 결과의 비교분석을 통해 이 연구에서 제안한 스트럿 유효강도 식의 적합성을 평가하였다.

• 한국도로학회논문집
• /
• 제5권3호
• /
• pp.1-9
• /
• 2003

본 논문은 시멘트 콘크리트 포장 위에 덧씌우기한 아스팔트 콘크리트 포장에서 발생하는 반사균열 제어를 위해 줄눈 실링재를 사용한 포장에서의 반사균열을 평가하기 위하여 수행되었다. 사용된 시험방법은 전단반사균열 모사실험 방법으로 실내에서 덧씌우기 아스팔트의 반사균열 저항성 시험을 위해 개발된 시험기법이다. 실험을 통하여 줄눈 실링재는 반사균열 제어에 효과가 있는 것으로 나타났다. 실링재 E를 사용하였을 때 피로수명은 가장 크게 나타났으나 수평변형은 상대적으로 크게 나타났고, B의 경우 수평변형은 가장 적게 나타났고 동적 안정도도 가장 크게 나타났다. 일반적으로 실링재의 인장강도가 높은 것일수록 혼합물의 반사균열저항성이 더 좋았다.

• Structural Engineering and Mechanics
• /
• 제73권5호
• /
• pp.543-554
• /
• 2020

This paper aims to investigate the seismic performance of RC short columns and long columns with welding stirrups. Through the low-cyclic horizontal loading test of specimens, the seismic performance indexes such as failure modes, hysteretic curve, skeleton curve, ductility, energy dissipation capacity, stiffness degradation and strength degradation were emphatically analyzed. Furthermore, the effects of shear span ratio, stirrups ratio and axial compression ratio on the performance of specimens were studied. The results showed that the seismic performance of the RC short columns with welding stirrups were basically the same as that of the RC short columns with traditional stirrups, but the seismic performance of RC long columns with welding stirrups was better than that of RC long columns with traditional stirrups. The seismic performance of RC short columns and long columns with welding stirrups could be improved by increasing stirrup ratio and shear span ratio and reducing axial pressure ratio. Moreover, the welding stirrup have the advantages of steel saving, industrialization and standardization production, convenient construction, and reducing time, which indicated that the welding stirrups could be applied in practical engineering.

• Steel and Composite Structures
• /
• 제49권1호
• /
• pp.19-30
• /
• 2023

Steel-concrete composite slabs represent a very efficient floor solution combining the key performance of two different materials: the steel and the concrete. Composite slab response is governed by the degree of the interaction between these two materials, mainly depending by chemical and mechanical bond. The latter is characterized by a limited degree of confinement if compared with the one of the rebars in reinforced concrete members while the former is remarkably influenced by the type of concrete and the roughness of the profiled surface, frequently lubricated during the cold-forming manufacturing processes. Indeed, owing to the impossibility to guarantee a full interaction between the two materials, a key parameter governing slab design is represented by the horizontal shear-bond strength, which should be always experimentally estimated. According to EC4, the design of the slab bending resistance, is based on the simplified assumption that the decking sheet is totally yielded, i.e., always in plastic range, despite experimental and numerical researches demonstrate that a large part of the steel deck resists in elastic range when longitudinal shear collapse is achieved. In the paper, the limit strain for composite slab, which corresponds to the slip, i.e., the debonding between the two materials, has been appraised by means of a refined numerical method used for the simulation of experimental results obtained on 8 different composite slab types. In total, 71 specimens have been considered, differing for the properties of the materials, cross-section of the trapezoidal profiled metal sheets and specimen lengths.

• 한국지진공학회논문집
• /
• 제15권4호
• /
• pp.45-54
• /
• 2011

경계요소를 가지는 철근콘크리트 전단벽의 비선형 해석을 위한 간편 모델을 제안하였다. 이 간편 모델은 전단벽의 휨 및 전단 거동을 스프링요소로 나타낸 거시적 모델이다. 휨거동은 벽체의 단면해석을 기초로 한 모멘트강도와 회전능력을 벽체 양단의 수직 스프링요소로 나타내었다. 경계요소를 가지는 전단벽은 휨거동에 의해 지배되므로 전단거동은 휨거동에 바탕하여 변수를 계산하였고 중앙부 수평 스프링요소로 나타내었다. 제안된 모델은 전단벽 정적이력시험 결과와 비교한 후 비선형동적해석을 수행하여 사용된 이력법칙 및 변수들의 타당성을 조사하였다. 비선형동적해석을 이용한 변수연구를 통하여 내진성능평가의 주요변수인 요구값과 성능값에 미치는 영향을 검토하였다. 그 결과 전단력-전단변형 관계에서 약간의 차이가 있지만 전단벽의 전체거동은 잘 일치하였으며, 주요 변수의 변화에 대해 요구값과 성능값도 일정하게 변화하므로 제안된 해석모델은 경계요소를 가진 철근콘크리트 전단벽에 알맞은 것으로 판단된다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.49-54
• /
• 2000

Several soil parameters can be calculated for results of Piezocone test; sensitivity, soil classification, OCR, undrained shear strength, coefficient of consolidation etc., and used to analysis geotechnical problems. Particularly, the coefficient of consolidation which is related to degree of consolidation varies according to rigidity index(I/sub r/). In this study, rigidity index(I/sub r/) was analyzed by Roy's formula. Trixial tests and unconfined compression tests data in the ten sites was analyzed. In conclusion, rigidity index(I/sub r/) was suggested such as rigidity index(I/sub r/) = 15∼60, average rigidity index value(I/sub r/) of approximately 33 within a country.

• 소음진동
• /
• 제6권4호
• /
• pp.431-438
• /
• 1996

The channel type structure which has large openings is frail with respect to torsional strength, and the horizontal-torsional motion is highly coupled, because of the large difference between the centroil and the shear center. Also, a discontinuous boundary phase is came from tansition section between the opened section and the closed section. To analyze the Bending- Torsional coupled mode parameters for the channel type structure, the Transfer Matrix Method was used. Comparing the result of F.D.M.T.M.M yields good results in relatively low frequency region.