• 한국결정성장학회지
• /
• 제27권1호
• /
• pp.18-21
• /
• 2017

본 연구에서는 homogeneous precipitation method를 통하여 구형의 단분산(monodispersed) YAG : $Ce^{3+}$를 합성했다. 단분산 YAG : $Ce^{3+}$의 전구체를 합성하는 과정에서 aluminum ion들이 먼저 석출되어 aluminum 화합물을 형성하고 후에 yttrium 화합물들이 aluminum 화합물들의 표면에서 석출된다. 합성된 전구체를 파우더형태로 얻기 위해 건조과정을 거치는데, oven에서 건조했을 때 보다 동결건조기에서 건조했을 때 비교적 구형의 단분산 YAG : $Ce^{3+}$ 입자를 얻을 수 있었다. 하소 과정에서 공정을 진행하는 온도로서 $1100^{\circ}C$와 $1200^{\circ}C$를 비교해 보았다. 실험 결과 $1200^{\circ}C$의 온도로 상압에서 6시간 동안의 하소 과정을 진행하였을 때 400~500 nm 입자크기를 가진 단분산된 구형의 나노 YAG : $Ce^{3+}$ 입자가 합성되었다.

• 한국자동차공학회논문집
• /
• 제19권1호
• /
• pp.1-8
• /
• 2011

In recent years, there has been an interest in early-injection diesel engines as it has the potential of achieving a more homogeneous and leaner mixture close to TDC compared to standard diesel engine. The more homogeneous mixture may result in reduced NOx and soot emissions and higher efficiency in homogeneous charge compression ignition engines. While earlier studies have shown that a reduction in NOx emissions from HCCI engine is possible, there are some significant problems including the control of ignition timing and combustion rate. In order to investigate the effect of EGR and hydrogen enriched gas on combustion characteristics and emissions, an experiments with single cylinder CRDi engine were carried out concerning the formation of various premixed charge, which can achieved by early injection, EGR and hydrogen enriched gas. EGR was not effective to further reduce NOx and PM emissions. It was found that NOx emissions were decreased with an introduction of hydrogen enriched gas and an adequate diesel fuel amount.

• 한국재료학회지
• /
• 제29권6호
• /
• pp.343-348
• /
• 2019

Structural and mechanical effects of the dynamical precipitation in two copper-base alloys have been investigated over a wide range of deformation temperatures. Basing upon the information gained during the experiment, also some general conclusion may be formulated. A one concerns the nature of dynamic precipitation(DP). Under this term it is commonly understood decomposition of a supersaturated solid solution during plastic straining. The process may, however, proceed in two different ways. It may be a homogeneous one from the point of view of distribution and morphological aspect of particles or it may lead to substantial difference in shape, size and particles distribution. The effect is controlled by the mode of deformation. Hence it seems to be reasonable to distinguish DP during homogeneous deformation from that which takes place in heterogeneously deformed alloy. In the first case the process can be analyzed solely in terms of particle-dislocation-particle interrelation. Much more complex problem we are facing in heterogeneously deforming alloy. Deformation bands and specific arrangement of dislocations in form of pile-ups at grain boundaries generate additional driving force and additional nucleation sites for precipitation. Along with heterogeneous precipitation, there is a homogeneous precipitation in areas between bands of coarse slip which also deform but at much smaller rate. This form of decomposition is responsible for a specially high hardening rate during high temperature straining and for thermally stable product of the decomposition of alloy.

• 한국분말재료학회지
• /
• 제15권5호
• /
• pp.378-385
• /
• 2008

This article presents the successful consolidation of the mixed Co and Diamond powders for a drilling segment by the combined application of magnetic pulsed compaction (MPC) and subsequent sintering, and their properties were analyzed. Homogeneous hardness (Hv 220) and density (97%) of sintered bulks fabricated by MPC were obtained by the new technique, where higher pressure has been employed for short period of time than that of general process. A fine microstructure and homogeneous hardness in the consolidated bulk were observed without cracks. Relatively higher drilling speed of 9.61 cm/min and life time of 6.55 m were found to the MPCed specimens, whereas the value of the specimens fabricated by general process was 11.71 cm/min and 7.96 m, respectively. A substantial improvement of mechanical properties of segment was achieved through this study.

• 열처리공학회지
• /
• 제26권5호
• /
• pp.233-240
• /
• 2013

Rapid and homogeneous heating in heat treatment has been a challenging engineering issue throughout a heating temperature over $1,000^{\circ}C$. Induction heating has been widely used in field of heat treatment compared with conventional heating system. Advantages in homogeneous heating, simple fabrication, and repeatable use can be efficiently made with the induction heater. In this paper, numerical analysis of an induction coil system for heat flux gauge heating is performed. The effect of configuration on the heating performance was considered in various cases of the coil radius, distance between the winding, relative height difference between the heat flux gauge and the coil, and the applied current frequency. Temperature distribution within the heat flux gauge at frequency-steady state was calculated with a finite element method. Sensitivity analysis was also performed and the relative importance of 2 key parameters; coil radius, distance between the winding, were taken as main contributors for induction heating.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2002년도 추계학술발표강연 및 논문개요집
• /
• pp.178-178
• /
• 2002

• 세라미스트
• /
• 제21권3호
• /
• pp.302-308
• /
• 2018

This work reported the trends of bioceramic materials for beauty-care applications with the several represent examples - tone-up, sun-care and anti-pollution cosmetics. The development of cosmetic techniques was discussed and reviewed with various ceramic hybrid materials. Moreover, we also reported the preparation and application of functional cosmetics with silicified liposome particles as a good make-up material for controlled release with natural compounds. The homogeneous loading and highly controlled-release formulation with porous and silicified ceramic liposome ceramic materials were discussed.

• 한국안전학회지
• /
• 제6권2호
• /
• pp.5-13
• /
• 1991

In this paper, the interfacial stress intensity factors( $K_{i}$＝ $K_1$＋i $K_2$) for the edge interface crack in the dissimilar materials(isotropic-isotropic materials, isotropic-composite materials) were analysed by BEM(Boundary Element Method). The fatigue crack growth behaviour was investigated by load constant fatigue test. From the experimental results, the relationship between da/dN and interfacial stress intensity facto, ( $K_{i}$ or $K_1$) can be expressed by Paris'law for homogeneous materials.s.s.

• 한국CDE학회논문집
• /
• 제15권2호
• /
• pp.136-143
• /
• 2010

Realistic Modeling is to maximize the reality of the environment in which perception is made by virtual environment or remote control using two or more senses of human. Especially, the field of haptic rendering, which provides reality through interaction of visual and tactual sense in realistic model, has brought attention. Haptic rendering calculates the force caused by model deformation during interaction with a virtual model and returns it to the user. Deformable model in the haptic rendering has more complexity than a rigid body because the deformation is calculated inside as well as the outside the model. For this model, Gibson suggested the 3D ChainMail algorithm using volumetric data. However, in case of the deformable model with non-homogeneous materials, there were some discordances between visual and tactual sense information when calculating the force-feedback in real time. Therefore, we propose an algorithm for the Volume Haptic Rendering of non-homogeneous deformable object that reflects the force-feedback consistently in real time, depending on visual information (the amount of deformation), without any post-processing.

• Nuclear Engineering and Technology
• /
• 제46권6호
• /
• pp.857-862
• /
• 2014

Mechanical alloying under various gas atmospheres such as Ar, an Ar-$H_2$ mixture, and He gases were carried out, and its effects on the powder properties, microstructure and mechanical properties of ODS ferritic steels were investigated. Hot isostatic pressing and hot rolling processes were employed to consolidate the ODS steel plates. While the mechanical alloyed powder in He had a high oxygen concentration, a milling in Ar showed fine particle diameters with comparably low oxygen concentration. The microstructural observation revealed that low oxygen concentration contributed to the formation of fine grains and homogeneous oxide particle distribution by the Y-Ti-O complex oxides. A milling in Ar was sufficient to lower the oxygen concentration, and this led a high tensile strength and fracture elongation at a high temperature. It is concluded that the mechanical alloying atmosphere affects oxygen concentration as well as powder particle properties. This leads to a homogeneous grain and oxide particle distribution with excellent creep strength at high temperature.