• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1997.10a
• /
• pp.37-42
• /
• 1997

This paper describes result of experiment of parameters affecting the micro hole drilling time, kind of assisting gas and it's pressure. The result reveals that parameter value of 0.08J, 20Hz, dwell time of 300 microseconds can be a good machining condition to make micro hole diameter range of 50-70${\mu}{\textrm}{m}$, Assistant gas such air, O2, Ar, N2 was adapted. Assistant gas of air makes heat affected zone enlarge due to burning of material, also it makes hole irregular and damage because of refusion stick to caused by chemical reaction with Al2O3 ceramic material. O2(99.9%) has good characteristic to get good drilling and smooth surface on pressure of 0.2kgf/$\textrm{cm}^2$, but it is expensive. Ar, N2 makes material burn and crack severely and proved to be an appropriate but, Ar was better than N2.

• Journal of Power System Engineering
• /
• v.2 no.2
• /
• pp.73-80
• /
• 1998

The identification of drilling joint dynamics which consists of drilling and structural dynamics and the on-line time series detection of malfunction process is substantial not only for the investigation of the static and dynamic characteristics but also for the analytic realization of diagnostic and control systems in drilling. Therefore, We have discussed on the comparative assessment of two recursive time series modeling algorithms that can represent the drilling operation and detect the abnormal geometric behaviors in precision roundshape machining such as turning, drilling and boring in precision diemaking. For this purpose, simulation and experimental work were performed to show the malfunctional behaviors for drilling operation. For this purpose, a new two recursive approach (Recursive Extended Instrument Variable Method : REIVM, Recursive Least Square Method : RLSM) may be adopted for the on-line system identification and monitoring of a malfunction behavior of drilling process, such as chipping, wear, chatter and hole lobe waviness.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.2
• /
• pp.79-83
• /
• 2001

A verification of multi-spindles drilling NC data is presented. The drilling of multi-spindles can offer productivity over three times as fast as that of single spindle. The most important things in machining tube sheet are precision of hole position and machining time. The drilling of multi-spindles has difficulties in controlling many motors to drive spindles and assign a correspondent number to each spindles. Multi-spindles drilling has different codes from CNC milling ; many subroutines, assignment of spindle, and so on. The conventional method, which inspects the NC code of the drilling, is to drill holes on a thin plate or tube sheet previously. The method results in low productivity because it consumed long machining time and welding for correction. This paper describes details of multi-spindles NC code and operation of multi-spindles drilling machine. A verification software of the multi-spindles drilling NC code is developed on the details.

• Journal of Drive and Control
• /
• v.16 no.4
• /
• pp.114-116
• /
• 2019

• Proceedings of the SAREK Conference
• /
• 2007.06a
• /
• pp.72-72
• /
• 2007

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.121-122
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.599-600
• /
• 2010

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.1
• /
• pp.134-140
• /
• 2017

CFRP has many industrial applications due to its low weight and high strength properties. CFRP is a composite material composed of carbon fibers embedded in a polymer matrix; it provides excellent resistance to fatigue wear, corrosion, and breakage due to fatigue. It is increasingly demanded in aircraft, automotive, and medical industries due to its superior properties to aluminum alloys, which were once considered the most suitable for specific applications. The basic machining methods of CFRP are drilling and route milling. However, in the case of drilling, the delamination of each layer, uncut fiber, resin burning, spalling, and exit burrs are barriers to successful application. This paper investigates the occurrence of exit burrs when drilling holes with ultrasonic vibration. Depending on design parameters such as the point angle, the characteristics of hole drilling were identified and appropriate machining conditions were considered.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.10
• /
• pp.40-44
• /
• 2010

Laser drilling is an enabling technology for Through Silicon Via (TSV) interconnect applications. Recent advances in picoseconds laser drilling of blind, micron sized vias in silicon is presented here highlighting some of the attractive features of this approach such as excellent sidewall quality. In this study, we dealt with comparison of heat affection around drilled hole between a picosecond laser and a nanosecond laser process under the UV wavelength. Points which special attention should be paid are that picosecond laser process lowered experimentally recast layer, surface debris and micro-crack around hole in comparison with nanosecond laser process. These finding suggests that laser TSV process has possibility to drill under $10{\mu}m$ via. Finally, the laser drilling platform was constructed successfully.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.1
• /
• pp.8-15
• /
• 2018

Recently, the manufacturing market for low-cost airlines has led to an increase in aircraft demand. Most processes in the production of these aircrafts are manual such as drilling, sealing, and swaging. A drilling and riveting machine is a numerical-control based equipment that automatically performs drilling, sealing, and swaging operations. The accuracy of the drilled holes and the exit burr length has a significant impact on the quality of the aircraft wing during assembly. This study was conducted to identify the conditions necessary to maintain a uniform quality by controlling the rotation speed of the spindle, which directly affects the hole diameter and the quality of the exit burr.