• Korean Journal of Agricultural Science
• /
• v.47 no.4
• /
• pp.867-884
• /
• 2020

Trypoxylus dichotomus is highly utilized in the domestic insect industry and bred at many farms nationwide. Recently, the number of farmers has been increasing due to the expansion of its use in food and medicine. However, the traditional breeding methods have high economic costs, which include relatively large breeding boxes, large amounts of sawdust and a 2 to 1 ratio (or higher) of female to male. Thus, it is essential to develop a cost-effective breeding method. In this study, a breeding cage with a partition was designed and used to investigate the reproduction rate of T. dichotomus with only a single pair of male and female insect. According to the investigation, the average number of eggs laid in the un-partitioned breeding cage was 93.6, and 121.3 eggs were laid in the partitioned breeding cage. This result shows that T. dichotomus lays more eggs in the partitioned breeding cage rather than in the un-partitioned breeding cage. In addition, it was found that T. dichotomus tends to lay more eggs in compressed sawdust, which was harder than the common fermented sawdust. Through a wind-tunnel assay, it was shown that the ovipositing female recognizes the eggs and avoids them to disperse their eggs elsewhere. These results indicate that the partitioned breeding cage may increase the hardness of the sawdust, restrict the adult's movement and provide a new place for oviposition for the female, and therefore results in an increased reproduction rate with less cost.

• International journal of steel structures
• /
• v.18 no.5
• /
• pp.1525-1540
• /
• 2018

A test rig with multi-functional purposes was specifically designed and manufactured to study the behavior of multi-planar welded tubular joints subjected to multi-planar concurrent axial loading. An experimental investigation was conducted on full-scale welded tubular joints with each consisting of one chord and eight braces under monotonic loading conditions. Two pairs or four representative specimens (two specimens for each joint type) were tested, in which each pair was reinforced with two kinds of different internal stiffeners at the intersections between the chords using welded rectangular hollow steel sections (RHSSs) and the braces using rolled circular hollow steel sections (CHSSs) and welded RHSSs. The effects of different internal stiffeners at the chord-brace intersection on the load capacity of joints under concurrent multi-planar axial compression/tension are discussed. The test results of joint strengths, failure modes, and load-stress curves are presented. Finite element analyses were performed to verify the experimental results. The study results show that the two different joint types with the internal stiffeners at the chord-brace intersection under axial compression/tension significantly increase the corresponding ultimate strength to far exceed the usual design strength. The load carrying capacity of welded tubular joints decreases with a higher degree of the manufacturing imperfection in individual braces at the tubular joints. Furthermore, the interaction effect of the concurrent axial loading applied at the welded tubular joint on member stress is apparent.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.6
• /
• pp.57-66
• /
• 2004

To study the efficient usage of small diameter logs and woods containing defects such as knots, slope of the grain and decay, six types of finger-jointed woods with various finger profiles were made of poplar, pine and oak with different density. We investigated the effect of finger profile on static bending strength performances of finger-jointed woods. The efficiency of bending MOE, MOR and deflection showed the highest value in poplar finger-jointed wood with the lowest density of three species, and the lowest value in oak finger-jointed wood with the highest density of three species. The values markedly decreased with increasing finger pitch for finger-jointed wood glued with polyvinyl acetate (PVAc) resin for all tested species, whereas for the finger-jointed wood glued with resorcinol-phenol formaldehyde (RPF) resin, the influence of finger pitch on the efficiency of MOE was not found in all tested species, and those on the efficiency of MOR and deflection indicated the same trend as finger-jointed wood glued with PVAc resin in the case of pine and oak finger-jointed wood with higher densities. It was found that the values tended to decrease with increasing density of species on the whole and the desirable finger pitches were L (6.8 mm) for poplar, M (4.4 mm) for pine and S (3.5 mm) for oak in a view of economy. For finger-jointed wood glued with PVAc resin, the fitness between a tip and a root width of a pair of fingers δ of 0.5 mm indicated the highest efficiency of MOE for all species. And, the influence of δ on MOR was only found in oak finger-jointed wood glued with RPF resin and the desirable δ value for oak was 0.1 mm. However, it was found that the influence of δ on the strength performance was very small.

• The Journal of Society for e-Business Studies
• /
• v.26 no.4
• /
• pp.1-13
• /
• 2021

With the development of big data-related technologies, it has become possible to process vast amounts of data that could not be processed before. Accordingly, the establishment of an automated data selection and fusion process for the realization of big data-based services has become a necessity, not an option. In this paper, we propose an automation technique to create meaningful new information by fusing datasets containing spatial information. Firstly, the given datasets are embedded by using the Node2Vec model and the keywords of each dataset. Then, the semantic similarities among all of datasets are obtained by calculating the cosine similarity for the embedding vector of each pair of datasets. In addition, a person intervenes to select some candidate datasets with one or more spatial identifiers from among dataset pairs with a relatively higher similarity, and fuses the dataset pairs to visualize them. Through such semi-automatic data fusion processes, we show that significant fused information that cannot be obtained with a single dataset can be generated.

• Steel and Composite Structures
• /
• v.41 no.5
• /
• pp.681-695
• /
• 2021

Many existing transmission or communication towers designed several decades ago have undergone nonreversible performance degradation, making it hardly meet the additional requirements from upgrades in wind load design codes and extra services of electricity and communication. Therefore, a new-type non-destructive reinforcement method was proposed to reduce the on-site operation of drilling and welding for improving the quality and efficiency of reinforcement. Six built-up steel angle members were tested under compression to examine the reinforcement performance. Subsequently, the cyclic loading test was conducted on a pair of steel angle tower sub-structures to investigate the reinforcement effect, and a simplified prediction method was finally established for calculating the buckling bearing capacity of those new-type retrofitted built-up steel angles. The results indicates that: no apparent difference exists in the initial stiffness for the built-up specimens compared to the unreinforced steel angles; retrofitting the steel angles by single-bolt clamps can guarantee a relatively reasonable reinforcement effect and is suggested for the reduced additional weight and higher construction efficiency; for the substructure test, the latticed substructure retrofitted by the proposed reinforcement method significantly improves the lateral stiffness, the non-deformability and energy dissipation capacity; moreover, an apparent pinching behavior exists in the hysteretic loops, and there is no obvious yield plateau in the skeleton curves; finally, the accuracy validation result indicates that the proposed theoretical model achieves a reasonable agreement with the test results. Accordingly, this study can provide valuable references for the design and application of the non-destructive upgrading project of steel angle towers.

• The Bulletin of The Korean Astronomical Society
• /
• v.46 no.2
• /
• pp.70.1-70.1
• /
• 2021

We examine the HI gas kinematics and distributions of galaxy pairs in group or cluster environments from high-resolution Australian Square Kilometer Array Pathfinder (ASKAP) WALLABY pilot observations. We use 32 well-resolved close pair galaxies from the Hydra, Norma, and NGC 4636, two clusters and a group of which are identified by their spectroscopy information and additional visual inspection. We perform profile decomposition of HI velocity profiles of the galaxies using a new tool, BAYGAUD which allows us to separate a line-of-sight velocity profile into an optimal number of Gaussian components based on Bayesian MCMC techniques. Then, we construct super profiles via stacking of individual HI velocity profiles after aligning their central velocities. We fit a model which consists of double Gaussian components to the super profiles, and classify them as kinematically cold and warm HI gas components with respect to their velocity dispersions, narrower or wider 𝜎, respectively. The kinematically cold HI gas reservoir (M_cold/M_HI) of the paired galaxies is found to be relatively higher than that of unpaired control samples in the clusters and the group, showing a positive correlation with the HI mass in general. Additionally, we quantify the gravitational instability of the HI gas disk of the sample galaxies using their Toomre Q parameters and HI morphological disturbances. While no significant difference is found for the Q parameter values between the paired and unpaired galaxies, the paired galaxies tend to have larger HI asymmetry values which are derived using their moment0 map compared to those of the non-paired control sample galaxies in the distribution.

• Journal of The Korean Astronomical Society
• /
• v.56 no.1
• /
• pp.11-22
• /
• 2023

We report the result of a high-resolution spectroscopic study on seven magnesium (Mg) enhanced stars. The high Mg abundances in these stars imply that they were born in an environment heavily affected by the nucleosynthesis products of massive stars. We measure abundances of 16 elements including Mg and they show various abundance patterns implying their diverse origin. Three of our program stars show a very high Mg to Si ratio ([Mg/Si] ≈ 0.18-0.25), which might be well explained by fall-back supernovae or by supernovae with rapid rotating progenitors having an initial mass higher than about 20 M_⊙. Another three of our program stars have high light to heavy s-process element ratios ([Y/Ba] ≈ 0.30-0.44), which are consistent with the theoretical prediction of the nucleosynthesis in rapidly rotating massive stars with an initial mass of about M = 40 M_⊙. We also report a star having both high Y ([Y/Fe] = 0.2) and Ba ([Ba/Fe] = 0.28) abundance ratios, and it also shows the highest Zn abundance ratio ([Zn/Fe] = 0.27) among our sample, implying the nucleosynthesis by asymmetric supernova explosion induced by very rapid rotation of a massive progenitor having an initial mass between 20 M_⊙ ≲ M ≲ 40 M_⊙. A relative deficiency of odd-number elements, which would be a signature of the pair-instability nucleosynthesis, is not found in our sample.

• The Korean Journal of Applied Statistics
• /
• v.22 no.2
• /
• pp.329-340
• /
• 2009

For complex diseases such as diabetes, hypertension, it is believed that model-free methods might work better because they do not require a precise knowledge of the mode of inheritance controlling the disease trait. This is done by estimating the sharing probabilities that a pair shares zero, one, or two alleles identical by descent(IBD) and has some specific branches of test procedure, i.e., the mean test, the proportion test, and the minmax test. Among them, the minmax test is known to be more robust than others regardless of genetic mode of inheritance in current use. In this study, we compared the power of the methods which are based on minmax test and considering weighting schemes for sib-pairs to analyze sibship data. In simulation result, we found that the method based on Suarez' was more powerful than any others without respect to marker allele frequency, genetic mode of inheritance, sibship size. Also, The power of both Suarez- and Hodge-based methods was higher when marker allele frequency and sibship size were higher, and this result was remarkable in dominant mode of inheritance especially.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.5
• /
• pp.2043-2049
• /
• 2015

Background: Serum Golgi protein 73 (GP73) as a novel and potential marker for diagnosing hepatocellular carcinoma (HCC) have been found to be elevated in HCC patients and associated with clinical variables representing tumor growth and invasiveness. The aim of this study was to prepare a pair of monoclonal antibodys (mAbs) against GP73 and develop a newly designed double-antibody sandwich enzyme-linked immunosorbent assay (s-ELISA), which would be used in the detection of serum GP73 (sGP73) as well as in the diagnosis of HCC. Materials and Methods: Produced by prokaryotic expression, the purified recombinant GP73 (rGP73), produced by prokaryotic expression, was used to immunize the Balb/c mice. Two hybridoma cell lines against GP73 were obtained by fusing mouse Sp2/0 myeloma cells with spleen cells from the immunized mice. The titers of anti-GP73 mAb reached 1:243,000. Western blotting analysis and Immunohistochemistry staining revealed that anti-GP73 mAb could recognize GP73 protein. The double-antibody s-ELISA was successfully established and validated by 119 HCC and 103 normal serum samples. Results: showed that the detection limit of this method could reach 1.56 ng/ml, and sGP73 levels in HCC group (mean=190.6 ng/ml) were much higher than those of in healthy controls (mean=70.92 ng/ml). Conclusions: Results of our study not only showed that sGP73 levels of HCC patients were significantly higher than those of healthy controls, but also indicated that the laboratory homemade anti-GP73 mAbs could be the optimal tool used in evaluating sGP73 levels, which would provide a solid foundation for subsequent clinical applications.

• The Journal of Korean Academy of Prosthodontics
• /
• v.55 no.4
• /
• pp.389-393
• /
• 2017

Purpose: The aim of this study is to evaluate the flexural strength of flexible resins and the flexibility of different resin splint (RS) systems in comparison with resin wire splint (RWS) system. Materials and methods: Three different resin materials (G-aenial flo, GA, GC; Superbond, SB, Sun medical; G-fix, GF, GC) were tested flexural strength test in accordance with ISO-4049:2000. For the flexibility test of splint systems, a artificial model with resin teeth was used to evaluate three types of resin splint systems (GA, SB, and GF) and one resin wire splint system. The left central incisor was simulated 'injured teeth' with third degree mobility. Three consecutively repeated measurements of periotest value were taken in horizontal direction, before and after splinting to access tooth mobility. The splinting effect was calculated through the periotest value. Differences were evaluated through One-way Anova and Tukey HDS post-hoc tests for pair-wise comparison (${\alpha}=.05$). Results: Although GA group showed significant higher flexural strength than SB and GF groups, all of three different resin splint systems produced a significantly higher and rigid splinting effect compared with 016" resin-wire splint system (P < .05). Conclusion: Within the limits of an in vitro study, it can be stated that resin splint systems are too rigid and may not be acceptable to treat tooth avulsion.