• 한국농공학회지
• /
• 제40권5호
• /
• pp.68-79
• /
• 1998

In the years, the concern about high-strength concrete which is new material has been heightened as a result of active research and development. Recently, as the building structure has been being bigger, higher, longer and more specialized, the demand of material with high-strength concrete for building has been increasing. The demand of high -strength concrete is expected to increase with expansion of usage about the complex concrete structures such as bridge structure as well as nuclear plants, underground structures, hydraulic structures and arctic area sturctures. In this research, silica-fume was used as an admixture in order to get a high-strength concrete. Water/binder ration was limited no more than 18 percent and the amount of unit cement was increased. In this study, a number of trial in concrete mix was carried out to get optimal mix design, and the target slump with $10{\pm}2cm$ was set for in-situ construction. High-strength concrete with cylinder strength of 1,200kgf/$cm^2$ in the 28-days was produced and tested. The static test was carried out to measure the ultimate load, the initial load of flexural and diagonal cracking, crack patterns, fracture modes. The load versus strain and load versus deflection relations were obtained form the static test. The test results were compared with the shear strengths predicted by the equations of ACI code 318-89 and orther researchers. Based on the test results, shear strength equation of reinforced concrete beam using high strength concrete was proposed. Form an evaluation of the results of this experimental investigation, it was concluded that shear strength after diagonal tention cracking diminished with the increase in compressive strength for beams.

• Journal of Biosystems Engineering
• /
• 제12권4호
• /
• pp.9-15
• /
• 1987

The vibrational characteristics of a radial-ply (155SR13 4PR) and a biased-ply tire (6.15-134PR) were investigated for examining the effects of tires with different structure on the ride characteristics of the vehicle. The natural frequencies at the tread band, mode shapes, and damping factors of two tires at the state of plane vibration were determined experimentally. The test work was performed at four levels of the inflation pressure, ranging from 171.7 kPa to 245.2 kPa, and three levels of the vertical load, deviating by 10% from the standard load designated by the Department of Transportation of the United States of America. The following results were drawn by the analysis of the test results: 1. The first-order natural frequencies of the radial-ply and the biased-ply tires at the tread band were 112 Hz and 159 Hz, respectively, at the state o f the free vibration when the inflation pressure of 196.2 kPa was applied. It was known that the biased-ply tire has higher resonant frequency than the radial-ply tire and the natural frequencies of the both tires move to the high frequency range as t he inflation pressure is increased. 2. The vibration modes of both tires were quite different. No big difference in mode shapes was examined as the inflation pressure was increased. But the natural frequencies of two tires were changed. For the radial-ply tire, no difference in mode shape was found whether the vertical load was applied or not. But a significant difference in mode shape was examined for the biased-ply tire. 3. Any difference was not found in damping factor as the different inflation pressures were applied. 4. When no vertical load was applied, damping factors of the radial-ply and biased-ply tire at the state of the natural vibration ranged from 2.6 to 5.9%, and from 4.1 to 7.8%, respectively. It was estimated that the radial-ply tire would have better cushioning than the biased-ply tire since the vertical spring rate of the radial-ply tire was much less than that of the biased-ply tire, even though the damping effect of the radial-ply tire was smaller than that of the biased-ply tire.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1995년도 춘계학술대회
• /
• pp.19-22
• /
• 1995

A biomechanical study was made to demonstrate the superior mechanical performance of the newly designed Miniplate staple to the conventional Coventry staple in high tibial osteotomy(HTO). Using twenty fresh porcine tibiae, the fixational strengh of the two different types of staple in HTO was compared. To minimize the error due to the specimen-to-specimen individuality, the bone mineral density of the tibiae was measured with a bone densitometry (Dual photon absorptionometer, Luner, USA) and those with $0.8\;{\sim}\;1.2\;gm/cm^2$ at the proximal tibia was used in the biomechanical test. Testing was performed on a material testing system (Autogram ET-5, Shimatzu, Japan) with aid of a commercial data processor (IBM 80386/ ASYST). Using two differant loading modes, 'pull-out' and 'push-out', the maximum resistant force required to release the staple from the substrate bone was recorded. In the pull-out test, ten non-osteotomized specimens were used and the staple was pullout by subjecting an axial tension on the head of the staple inserted. While in the pull-out test where ten tibiae osteotomized in the usual way of HTO were used, the staple was not directly loaded. In this testing, as a mimic condition of the natural knee, the distal part of the specimen tibia was pushed horizontally in order for the staple to be pulled out while the proximal tibia was fixed. The pull-out strength of Coventry staple and miniplate staple were found to be $27.88\;{\pm}\;5.12\;kgf$ and $182.47\;{\pm}\;32.75\;kgf$, respectively. The push-out strength of Coventry staple and miniplate staple were $18.40\;{\pm}\;4.47\;kgf$ and $119.95\;{\pm}\;19.06\;kgf$, respectively. The result revealed that miniplate staple had the pull-out/ push-out strength at least fivetimes higher than Coventry staple. Based on the measured data, it was believed that the newly designed miniplate staple could provide much better postoperative fixation in HTO. The postoerative application of long leg casting may not be needed after HTO surgery.

• Wind and Structures
• /
• 제19권4호
• /
• pp.421-441
• /
• 2014

With the assistance of typhoon field data at aerial elevation level observed by meteorological satellites and wind velocity and direction records nearby the ground gathered in Guangzhou Weather Station between 1985 and 2001, some key wind field parameters under typhoon climate in Guangzhou region were calibrated based on Monte-Carlo stochastic algorithm and Meng's typhoon numerical model. By using Peak Over Threshold method (POT) and Generalized Pareto Distribution (GPD), Wind field characteristics during typhoons for various return periods in several typical engineering fields were predicted, showing that some distribution rules in relation to gradient height of atmosphere boundary layer, power-law component of wind profile, gust factor and extreme wind velocity at 1-3s time interval are obviously different from corresponding items in Chinese wind load Codes. In order to evaluate the influence of typhoon field parameters on long-span flexible bridges, 1:100 reduced-scale wind field of type B terrain was reillustrated under typhoon and normal conditions utilizing passive turbulence generators in TJ-3 wind tunnel, and wind-induced performance tests of aero-elastic model of long-span Guangzhou Xinguang arch bridge were carried out as well. Furthermore, aerodynamic admittance function about lattice cross section in mid-span arch lib under the condition of higher turbulence intensity of typhoon field was identified via using high-frequency force-measured balance. Based on identified aerodynamic admittance expressions, Wind-induced stochastic vibration of Xinguang arch bridge under typhoon and normal climates was calculated and compared, considering structural geometrical non-linearity, stochastic wind attack angle effects, etc. Thus, the aerodynamic response characteristics under typhoon and normal conditions can be illustrated and checked, which are of satisfactory response results for different oncoming wind velocities with resemblance to those wind tunnel testing data under the two types of climate modes.

• 한국입자에어로졸학회지
• /
• 제18권1호
• /
• pp.1-8
• /
• 2022

Since 2019, the corona virus has been continuously affect human life. In particular, in the indoor space where people live, infection by airborne transmission of viruses is a problem. Among them, the spread in the subway, which is the main mode of transport for humans, can be serious. To solve this problem, our research team developed an ionic wind collector to collect and remove corona virus using an ionic wind collector and ozone. In order to apply the ionic wind collector to the subway, it must operate in two modes. Because large amounts of ozone are harmful to the human body. There is a mode that collects bio-aerosol from the air using ionic wind and a mode that inactivates viruses floating in the air by generating a large amount of ozone. As the applied voltage increased, the cleaning ability of the ionic wind collector increased, and the farther the distance between the discharge electrode and the ground plate, the higher the cleaning ability even at low current. In addition, clean air delivery rate (CADR) of an ionic wind collector was up to 5.5 m³/min. As a result of measuring the amount of ozone generated, it was confirmed that 50 ppb to 250 ppb was generated, and it was confirmed that ozone generation was controllable in the ionic wind dust collector.

• Earthquakes and Structures
• /
• 제23권1호
• /
• pp.35-57
• /
• 2022

This article presents a computationally efficient framework for multi-objective seismic design optimization of steel moment-resisting frame (MRF) structures based on the nonlinear dynamic analysis procedure. This framework employs the uniform damage distribution philosophy to minimize the weight (initial cost) of the structure at different levels of damage. The preliminary framework was recently proposed by the authors based on the single excitation and the nonlinear static (pushover) analysis procedure, in which the effects of record-to-record variability as well as higher-order vibration modes were neglected. The present study investigates the reliability of the previous framework by extending the proposed algorithm using the nonlinear dynamic design procedure (optimization under multiple ground motions). Three benchmark structures, including 4-, 8-, and 12-story steel MRFs, representing the behavior of low-, mid-, and high-rise buildings, are utilized to evaluate the proposed framework. The total weight of the structure and the maximum inter-story drift ratio (IDRmax) resulting from the average response of the structure to a set of seven ground motion records are considered as two conflicting objectives for the optimization problem and are simultaneously minimized. The results of this study indicate that the optimization under several ground motions leads to almost similar outcomes in terms of optimization objectives to those are obtained from optimization under pushover analysis. However, investigation of optimal designs under a suite of 22 earthquake records reveals that the damage distribution in buildings designed by the nonlinear dynamic-based procedure is closer to the uniform distribution (desired target during the optimization process) compared to those designed according to the pushover procedure.

• Composites Research
• /
• 제16권5호
• /
• pp.45-53
• /
• 2003

본 논문에서는 이차 본딩으로 접착된 복합재료-복합재료 Single-Lap 조인트 시편에 대해 인장 시험 및 수치해석을 통해 그 파손 특성을 조사하였다. 시편시험에서는 시험 중에 CCD 카메라 및 AE 센서를 이용해 초기 균열의 발생 및 진전양상에 대한 시험적인 관찰을 수행하였다. 시편에 대해 기하비선형 유한요소해석 및 VCCT(Virtual Crack Closure Technique)기법을 이용해 시편의 거동 및 변형율에너지방출률을 계산하고 세 가지 관찰된 초기 균열 모드에 대해 파손강도를 계산하였다. 인장시험에서 초기 균열은 모서리 계면 균열, 측면 계면 균열 및 층간 분리 균열의 세 가지 형태로 최종 파손의 60∼90% 하중에서 발생하였다. 주된 파손 모드는 접착제 계면 파손(adhesive failure) 및 적층판의 첫 번째 및 두 번째의 층간 분리 파손이었다. 두꺼운 접착제 층을 갖는 시편들은 초기균열이 낮은 하중에서 발생하였지만 균열진전에 대한 저항성 및 파손하중은 높게 나타났다. 층간분리파손은 주로 두꺼운 접착제의 경우에 발생하였다. 세 가지 초기 균열 모드에 대해 변형률에너지방출률은 Mode I의 G값이 Mode II의 G값보다 크게 계산되었다. Mode I 및 전체 G값은 측면 계면 균열, 모서리 계면 균열, 층간분리 균열의 순서로 크게 계산되었다.

• 한국대기환경학회지
• /
• 제29권3호
• /
• pp.325-337
• /
• 2013

The size-fractionated aerosol samples have been collected at Gosan Site of Jeju Island during the spring season of 2010, in order to examine the chemical composition characteristics of the Asian Dust and Non-Asian Dust particles. The concentrations of ${HCO_3}^-$, Al, and nss-$Ca^{2+}$ in $PM_{10}$ had tremendously increased during the heavy Asian Dust (March 20, 2010). The concentration ratios of Asian Dust to Non-Asian Dust for the soil species (nss-$Ca^{2+}$, ${HCO_3}^-$, Al, Fe, Ti, Mn) were 12.2~30.7, meanwhile those for the anthropogenic species (nss-${SO_4}^{2-}$, ${NH_4}^+$, ${NO_3}^-$, $K^+$, Zn, Pb, and Cu) were 2.9~7.8. During the heavy Asian Dust event, the concentration increase of ${NO_3}^-$ in $PM_{2.5}$ were much more apparent than those of nss-${SO_4}^{2-}$ and ${NH_4}^+$, and the soil species (nss-$Ca^{2+}$ and ${HCO_3}^-$) showed much higher concentration increase. The neutralization factor of $NH_3$ was higher than that of $CaCO_3$. However, the neutralization factor of $CaCO_3$ in $PM_{10}$ was exceptionally high during the heavy Asian Dust, showing the evidence of heavy migration of soil particles. From the study for size fractionated particles, it was found that nss-${SO_4}^{2-}$ and ${NH_4}^+$ were mostly distributed in fine particle mode, on the other hand, ${NO_3}^-$ existed evenly in both fine and coarse particle modes, and the soil species (nss-$Ca^{2+}$, Al, Fe, etc.) were mainly in the latter mode. During the heavy Asian Dust, in particular, the concentrations of ${NH_4}^+$, nss-${SO_4}^{2-}$, $K^+$, Zn, and Pb had increased in coarse particle mode as well.

• 대한교통학회지
• /
• 제18권5호
• /
• pp.69-82
• /
• 2000

교통체계가 지하철 중심의 대중교통체계로 변화되면서 지하철이용을 활성화하기 위한 적절한 연계체계를 구축할 필요성이 고조되고있다. 따라서, 본 연구에서는 부산시를 대상으로 타 목적통행에 비해서 중요한 비중을 차지하면서 비교적 안정적인 행태를 보이는 지하철 이용 통근 통학자를 대상으로 대표적인 연계교통수단인 시내버스, 마을버스, 택시 이용시 통행특성에 대한 체계적인 분석과 연계교통수단 선택행태에 대한 다항로짓모형을 구축하였다. 모형의 구축결과 연계교통수단선택시 큰 영향을 미치는 설명변수는 차외시간(OVTT), 차내시간(IVTT), 요금(T-FARE, S-FARE, B-FARE), 소득(INCOME), 성별(SEX), 연령(AGE) 순으로 나타났다. 그리고, 연계교통수단의 이용은 환승을 위한 단거리 통행이기 때문에 차외시간이 차내시간보다 수단선택시 더 큰 영향을 미치는 것으로 나타났다. 통행비용관련 변수들은 통행시간 변수들에 비해 연계수단선택시 큰 영향을 미치지 못하는 것으로 나타났다. 따라서 요금인하로 인한 수요증가 정책보다는 적정수준으로 요금을 인상하여 이로 인한 수입 등을 이용하여 교통시설의 확충 등 서비스 개선에 의한 대중교통의 통행시간을 단축시킬 수 있는 서비스의 개선이 요구된다. 또한 통행시간가치는 타의시간의 시간가치가 차내시간의 시간가치보다 현저히 높게 나타났으며, 아침 통근 ·통학시 요금보다는 시간을 중요하게 인식하여 택시의 시간가치가 시내버스, 마을버스의 시간가치보다 훨씬 높게 나타났다.

• 대한조선학회논문집
• /
• 제30권3호
• /
• pp.116-126
• /
• 1993

대형구조계의 진동해석에 효율적인 방법으로 알려진 부분구조 진동형 합성방법을 방법론적 관점에서 분류하면 부분구조계간의 연결부 경계조건을 어떻게 가정하는가에 따라 구속모드방법, 불구속 모드방법 및 혼합방법으로 대별할 수 있다. 이 방법들 중에서 불구속 모드방법이 보다 효율적이고 또 특정 부분구조의 실험결과 이용이 용이한 장점이 있으나 정확도가 떨어진다는 단점이 있다. 본 연구에서는 대형 구조계의 진동해석에 효율적이면서 정확도 높은 결과를 얻을 수 있는 불구속 모드방법을 정식화하였다. 불구속 모드방법의 정확도 향상 방안으로서 모드합성시 배제된 고차진동형의 영향을 잉여강성과 더불어 잉여관성 효과도 고려하여 보상하였고, 또 주파수이동기법을 도입하므로써 주관심 주파수 부근에서 더욱 정확도가 높은 결과를 얻을 수 있도록 함과 동시에 부분구조계가 semi-definite system일 경우 특이매트릭스를 처리해야 하는 문제점도 해결하였다. 상기방법의 정확도 및 계산효율성은 선체 2차원 단순화 모델을 포함한 일련의 유한요소모델에 대해 검증되었다. 상기방법에 의한 계산결과는 정확도에 있어서 진동형 합성에 이용된 부분구조계의 최고차 진동수 이하에서는 전체계를 직접 유한요소해석한 경우와 대등하고, 구속모드방법보다 효율적이면서 정확도가 더 높은 결과를 얻을 수 있음이 확인되었다.