• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.624-629
• /
• 2001

Two types of bolted lap joints, one with a viscoelastic layer and the other without the viscoelastic layer were chosen to analyze the dynamic characteristics of the joints with the mechanical properties of the bolts of the joints being taken as computational variables. The finite element method was used along with the impact hammer technique to verify the FEM model. The results in the bolted lap joints reveal that the higher the Young's Modulus for the bolts are the higher the natural frequencies results for the joints. However, the natural frequency differences in the first and second mode are not substantial but become noticeable in the higher modes. Lower natural frequencies were obtained for the bolted lap joints with the viscoelastic layer when compared with those of the bolted lap joints without the viscoelastic layer. And the differences in the natural frequencies for the two types of joints are relatively small in the first and second mode whereas in the higher mode the differences become significant. The loss factors were observed to be significant especially in the second mode for the bolted lap joints with the viscoelastic layer.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2008.10a
• /
• pp.62-65
• /
• 2008

In this paper, we estimated the D147 mode test, which is introduced as a new emission test mode for the driving car using diesel fuel. And we compared the D147 test mode, Lug-Down3 test mode and no load acceleration test mode. And the exhaust gas concentration between the three modes was compared. The exhaust concentration at the D147 mode is lower than the exhause concentration at the Lug-Down 3 mode and higher than that at the no load acceleration test mode. Also the correlation factor was estimated between the D147 mode and Lug-Down 3 mode.

• The Journal of the Acoustical Society of Korea
• /
• v.19 no.1
• /
• pp.54-60
• /
• 2000

There are many works to analyze a simple expansion chamber involving higher order modes. These works are classified to mode matching method, velocity potential method and finite element method. Among these methods, mode matching method has good performance at analyzing a concentric expansion chamber. Generally inlet/outlet pipe cross section area is smaller than middle chamber cross section area. So the number of higher order modes of inlet/outlet pipe can be fewer than that of middle chamber. But mode matching method must use the same number of higher order modes at inlet pipe, middle chamber and outlet pipe. Therefore the redundant modes of inlet/outlet pipe makes the computation time of mode matching method longer. In this paper, the new method, which can select number of each higher order modes of inlet pipe, middle chamber and outlet pipe, was suggested. And this method was compared to conventional mode matching method and finite element method in order to demonstrate the accuracy of the new method and to show that the new method can reduce a calculating time.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.453-453
• /
• 2007

Electrodeless fluorescent lamp exhibit two modes of operation: a low density mode in which the power is capacitively coupled to the plasma and which is known as the E-mode, and a higher density mode which is an inductive discharge known as the H-mode. The transition between these two(E to H) mode exhibits hysteresis. It is observed that transition currents change at different frequencies and hysteresis exists not only between the starting and minimum maintaining currents of the electromagnetic mode (H mode) discharge but also between the starting and minimum maintaining currents of the electrostatic mode (E mode) discharge. Hysteresis effect can be important role in dimming system.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.8
• /
• pp.59-65
• /
• 2004

In this paper, we propose Pseudo-TN IPS mde(Pseudo-Twisted Nematic In-Plane Switching mode) based on IT(In-plane switching Twisted nematic) mode that increase contrast ratio from improving optical characteristics and analyze the characteristics of Pseudo-TN IPS uude. Optical transmittance is 25% higher for the PTN-IPS mode than for the IT mode. Because aperture ratio of the PIN-IPS is increased. And the control of Liquid Crystal for adjusting optical transmittance is more easier than IT mode, because optical transmittance variation is linear with applying voltage. Contrast ratio is 8% lower for the PTN-IPS mode than for the IT mode in the horizontal direction. But, Contrast ratio is 20% higher for the PTN-IPS mode than for the IT mode in the vertical direction. It has also cell gap margin and many benefits of IT mode, this may be used very well in the future LC Cell design.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1560-1561
• /
• 2007

Electrodeless fluorescent lamp exhibit two modes of operation : a low density mode in which the power is capacitively coupled to the plasma and which is known as the E-mode, and a higher density mode which is an inductive discharge known as the H-mode. The transition between these two(E to H) mode exhibits hysteresis. It is observed that transition currents change at different frequencies and hysteresis exists not only between the starting and minimum maintaining currents of the electromagnetic mode (H mode) discharge but also between the starting and minimum maintaining currents of the electrostatic mode (E mode) discharge. Hysteresis effect can be important role in dimming system.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.422-425
• /
• 1988

The structure consisting of an E-plane dielectric slab partially filling a rectangular waveguide is examined with attention on those higher order mode propagation characteristics that are relevant to the design of nonreciprocal remanence ferrite phase shifters. The mechanisms for the elimination of $LSE_{11}$, $LSM_{11}$, $LSE_{12}$ modes are introduced. Experimental verification of elimination of higher order mode is shown in the form of insertion loss measurements.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.6
• /
• pp.7-11
• /
• 2009

The dynamic responses and drift forces in waves of a floating circular fish cage are analyzed considering hydroelastic effects. The method of generalized mode is used to calculate the hydroelastic responses of the floater of cage. The elastic mode shapes, generalized mass, and stiffness in dry mode are evaluated by using a structural analysis code. The higher-order boundary element method is adopted to analyze the interaction between fluid and deformable structure. Some results of vertical motions and drift forces are shown and compared with those for a rigid body.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.3
• /
• pp.310-315
• /
• 2009

This investigation was performed to study the characteristics of electricity and heat transfer that occur in the cylinder of electrode type humidifier during the process of water evaporation. Measurements were made to obtain the amount of water evaporation, the consumption of electric power, electrical conductivity, etc according to the materials and shapes of electrode. When the humidifier was in non-drain controlled mode, the number and amplitude of current cycle per minute increased gradually with the lapse of time, whereas for drain controlled mode, it decreased about 40[%] after draining water. It was found that for non-drain controlled mode, the thermal efficiency of humidifier which used SS400, STS316 and wire net electrode type was about 95~96[%] and it was 2~4[%] higher than that of drain controlled mode. Also, it was shown that the thermal efficiency of humidifier which used neighboring six-phase electrode balanced electrically was 4[%] higher than that of existing six-phase type.

• Journal of the Optical Society of Korea
• /
• v.18 no.2
• /
• pp.167-173
• /
• 2014

A novel multi-oxide layer structure for vertical cavity surface emitting laser (VCSEL) structures is proposed to achieve higher single mode output power. The structure has four oxide layers with different aperture sizes and thicknesses. The oxide layer thicknesses are optimized simultaneously to reach the highest single mode output power. A heuristic method is proposed for plotting the influence of these variable changes on the operation of optical output power. A comprehensive optical-electrical thermal-gain self-consistent VCSEL model is used to simulate the continuous-wave operation of the multi-layer oxide VCSELs. A comparison between optimized VCSELs with different structures is presented. The results show that by using multi-oxide layers with different thicknesses, higher single-mode optical output power could be achieved in comparison with multi-oxide layer structures with the same thicknesses.