• Journal of the Korean Society of Combustion
• /
• v.16 no.1
• /
• pp.46-51
• /
• 2011

Exhaust gas of an industrial furnace used at such as metallurgy or ceramic manufacturing usually contains thermal energy with high temperature which can be recycled by heat exchanger. However, when the temperature of the exhaust gas is high such as more than $1,000^{\circ}C$, ordinary metallic heat exchanger cannot fully recover the heat due to the limitation of operating temperature depending on the material property. In the present study, a compact ceramic heat exchanger of cross flow type is introduced and evaluated by heat exchange rate and operating temperature. The ceramic heat exchanger can endure the gas temperature more than $1,300^{\circ}C$, and its volumetric heat exchanging rate exceeds 1 MW/$m^3$. The experimental data is also compared with the previous numerical result which shows reasonable agreement. Meanwhile, the gas leakage rate is measured to be about 3~4%, and heat loss to environmental air is about 23~26% of the fuel energy.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.102-105
• /
• 2005

The mechanical properties of $SiC_f/SiC$ composites reinforced with continuous SiC fiber have been investigated in conjunction with the detailed analysis of their microstructures. Especially, the effect of test temperature on the characterization of $SiC_f/SiC$ composites was examined. In this composite system, a braiding Hi-Nicalon SiC fibric was selected as a reinforcement. $SiC_f/SiC$ composites have been fabricated by the reaction sintering process, using the complex matrix slurry with a constant composition ratio of SiC and C particles. The characterization of $RS-SiC_f/SiC$ composites was investigated by means of SEM, EDS and three point bending test. Based on the mechanical property-microstructure correlation, the high temperature applicability of $RS-SiC_f/SiC$ composites was discussed.

• Food Science and Biotechnology
• /
• v.17 no.5
• /
• pp.1010-1015
• /
• 2008

The effects of heat treatment on the physicochemical properties and mineral composition of sun-dried salt were investigated. The salts parched at high temperature were appeared the higher alkalinity and the lower oxidation-reduction potential (ORP) than the samples without heat treatment. The commercial salts (bamboo salt and yellow loess salt) and the sun-dried salt parched at high temperature had relatively higher sodium ion content (418-450 ppm) compared to that (418.0 ppm) of refined salt. The increase of calcium ion occurred in the salts parched at high temperature compared to the sun-dried salt without heat treatment, but the magnesium ion was vice versa. The commercial salt, yellow loess salt had highest turbidity (0.973) whereas sun-dried salt showed lowest level (0.097) among the tested samples. Turbidity of heat treatment samples decreased as solubility increased. The maximum concentration of dialyzed salt was reached after 4 hr regardless of various processed salts, but those had no difference significantly among the tested samples. The X-ray diffraction patterns of the parched sun-dried salts showed different peak intensity with common salts, and they were similar to the patterns of oxide salts, especially MgO. The maximum value (2.56%) of MgO appeared in the sun-dried salt parched at $1,400^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.55 no.4
• /
• pp.358-363
• /
• 2018

To improve the polarization property of cathodes, which is the main factor limiting the performance of protonic ceramic fuel cells (PCFCs), $K_2NiF_4-type$ $Pr_2NiO_{4+{\delta}}$, which is expected to exhibit a triple conducting property (proton, oxygen ion, and hole conductions) was applied to PCFCs and its properties were investigated. Low-temperature microwave heat-treatment was used to achieve both sufficient interface adhesion between the electrolyte and the cathode layers and suppression of the secondary phase formation due to migration of elements such as barium and cerium. Through this fabrication method, a high performance of $0.82W{\cdot}cm^{-2}$ and low ohmic resistance of $0.06{\Omega}{\cdot}cm^2$ were obtained in an $Ni-BaCe_{0.55}Zr_{0.3}Y_{0.15}O_{3-{\delta}}$ | $BaCe_{0.55}Zr_{0.3}Y_{0.15}O_{3-{\delta}}$ | $Pr_2NiO_{4+{\delta}}$ single cell at $650^{\circ}C$. This result verifies that the $K_2NiF_{4+{\delta}}-type$ cathode shows good chemical compatibility which, in turn, will make it a potent candidate as a PCFC cathode.

• Journal of the Korean Home Economics Association
• /
• v.47 no.1
• /
• pp.85-91
• /
• 2009

Dyeability and antimicrobial property of dyed pig skin with Coptis chinensis Franch was investigated. Dyestuff was extracted with water and concentrated. Pig skin was dyed and mordanted according to various dyeing temperature, dyeing time, dyestuff concentration, mordanting methods and kinds of mordants. The results of this experiment were as follows: 1. Dyeability of pig skin with Coptis chinensis Franch was best at 200%(owf) dyestuff concentration, 50${^{\circ}C}$ dyeing temperature, and 20min. dyeing time. 2. Pre-mordanting by Cu improved the K/S values of dyed pig skin. 3. Surface color and color difference of dyed pig skin showed various results according to the mordants used : generally their color was yellow, Al post-mordanted pig skin showed the greatest color difference. 4. Color fastness to drycleaning was considerably high in case of staining compared to fading. Fastness to light was improved by Cu-mordanting while other treatments were not effective. 5. Antimicrobial property of samples was not different (99.9%) between untreated and treated.

• Journal of the Korean Society for Heat Treatment
• /
• v.17 no.4
• /
• pp.216-222
• /
• 2004

Study was focused on the quenching embrittlement property of Zircaloy-4 cladding simulated Loss Of Coolant Accident (LOCA) environment in terms of high temperature oxidation and phase transformation. Property in LOCA condition of advanced cladding that contained Nb element was also investigated. Claddings were oxidized at given temperature and given time followed by water quenching. The results showed that ${\beta}$ phase which formed at quenching stage has an influence on cladding property. In case of advanced cladding, Nb retards cladding oxidation, thus enhances quenching resistance.

• Korean Journal of Materials Research
• /
• v.29 no.3
• /
• pp.189-195
• /
• 2019

The effect of C, Mn, and Al additions on the tensile and Charpy impact properties of austenitic high-manganese steels for cryogenic applications is investigated in terms of the deformation mechanism dependent on stacking fault energy and austenite stability. The addition of the alloying elements usually increases the stacking fault energy, which is calculated using a modified thermodynamic model. Although the yield strength of austenitic high-manganese steels is increased by the addition of the alloying elements, the tensile strength is significantly affected by the deformation mechanism associated with stacking fault energy because of grain size refinement caused by deformation twinning and mobile dislocations generated during deformation-induced martensite transformation. None of the austenitic high-manganese steels exhibit clear ductile-brittle transition behavior, but their absorbed energy gradually decreases with lowering test temperature, regardless of the alloying elements. However, the combined addition of Mn and Al to the austenitic high-manganese steels suppresses the decrease in absorbed energy with a decreasing temperature by enhancing austenite stability.

• Economic and Environmental Geology
• /
• v.22 no.2
• /
• pp.129-139
• /
• 1989

The anthracite coalfields of Korea are confined to the areas where sedimentary rocks of Permian and Jurassic are preserved. The Chungnam coalfield lies in the sedimentary rocks of Jurassic which belongs to the Daedong Supergroup (the Nampo group). For the property analysis of each coal seam interbeded in Daedong Supergroup, Seongju area is chosen and twelve coalseams are taken. Many standard tests have been established for optical analysis (maceral analysis, coalification degree measurement), chemical analysis (proximate, ultimate analysis) and physical analysis (ignition temperature, ash fusion temperature, hardgrove grindability index and X-ray diffraction). The Jurassic anthracite mainly consist of vitrinite and macrinite and the range of the reflectance is $R_{max}$ 5.0-6.5 which means metaanthracite rank. By the chemical composition analysis, it shows low H/C and high O/C value compare with international average value. By the physical analysis, it has very high ignition temperature ($531-584^{\circ}C$) and ash fusion temperature ($1510-1700^{\circ}C$) and very low combustion velocity (0.2-1.9 mg/min). The very wide range of the hardgrove grindability index (46-132) means that the grindability controlled mainly by the structural conditions of coal bearing strata.

• Tribology and Lubricants
• /
• v.11 no.1
• /
• pp.50-57
• /
• 1995

When engine oil is used under severe running condition, the Lubricational characteristics is very important. I have studied the Lubricational characteristics with Compound Additives of engine oil for the Falex wear test machine. Adding detergent (Ca-phenate) to engine oil, the seizure is more improved than in case of non-adding, and adding Zn-DTP (Zinc dialkyl dithio phosphate), the extreme pressure property is excellent at the high load. But when the PTFE (Polytetra Fluoro Ethylene) and MoS$_{2}$ (Molybdenum disulfide) are added, the temperature characteristics and the anti-wear property become excellent because the stability can be maintained in a high temperature. The result are as follows, it can be improved that when the compound of the Ca-phenate and Zn-DTP, MoS$_{2}$, PTFE, etc. was added to engine oil, the lubrication characteristics become better. It is argued that it is improved because of excellence of the anti-wear, the extreame pressure properties and the heat stability.

• Journal of Powder Materials
• /
• v.9 no.3
• /
• pp.153-160
• /
• 2002

A nitrogen gas atomized aluminum powder was consolidated by powder-in sheath rolling method. A pure aluminum tube with outer diameter of 12 mm and wall thickness of 1mm was used as a sheath. The aluminum tube filled with the aluminum powder, first, was cold-rolled to the thickness of 6mm for performing, and then consolidated by the cold rolling and/or subsequent hot rolling at 360, 460 and $560^{\circ}C$. The aluminum powder compact fabricated by the sheath rolling showed high relative density more than 0.96 at any rolling conditions. The 0.2% proof stress increased with increasing hot rolling reduction and hot rolling temperature. Tensile strength was hardly affected by change in the hot rolling reduction, whereas it decreased with increasing hot rolling temperature. The powder compact showed the large elongation when cold rolling or hot rolling reduction was large. It was found that the sheath rolling was an effective method for consolidation of aluminum powder.