• 한국자기학회지
• /
• 제27권1호
• /
• pp.1-8
• /
• 2017

플라이휠 에너지 저장 장치(Flywheel Energy Storage System, FESS)은 회전 운동 에너지를 저장하는 플라이휠 부분과 저장된 회전 에너지를 전기 에너지로 변환시키는 전동기/발전기 부분으로 구성된다. 일반적으로 플라이휠의 회전축은 전동기 및 발전기의 회전축과 동축 일체형으로 연결되고, 이때 전동기 및 발전기의 전자기 토크특성에 따른 동특성 변화는 전체 플라이휠 에너지 저장 장치의 충방전 특성과 기계적인 출력에 영향을 미친다. 본 논문에서는 5[kWh] 급 플라이휠 에너지 저장 장치 용 3상 유도전동기의 설계방법과 회전자 슬롯 수 변화에 따른 토크리플 특성과 고조파 영향을 중점적으로 분석하였다. 먼저, 플라이휠 에너지 저장 장치의 용량과 관성 모멘트에 의한 회전운동에너지의 관계식으로부터 플라이휠 크기와 전동기의 회전자 크기를 산정하는 방법을 제안하였다. 또한 플라이휠 에너지 저장 장치의 회전축의 고속구동 조건을 반영하여, 고속운전 영역에서의 전동기 토크리플 저감을 위한 유도전동기 회전자 슬롯수를 선정하였다. 이로부터 본 논문에서는 전동기 회전축과 동축으로 구성된 플라이휠의 소음 진동을 줄이고 고효율 충방전 특성을 구현하고자 한다.

• 한국정보전자통신기술학회논문지
• /
• 제9권2호
• /
• pp.178-184
• /
• 2016

본 논문에서는 전력에너지를 사용하는 산업체의 전동기용량이 점차 증가하고 있다. 전동기는 기동시 기동전류로 전압강하가 발생한다. 이 기동전류가 전력계통에서 대형 전동기 기동 시 전압강하로 기동이 어려워 인접한 전력계통에 나쁜 영향을 미치게 된다. 또한 전동기는 부하의 크기에 따라 토크를 내는 것으로 토크의 크기에 따라 속도가 변하고 속도는 전동기 기동에 중요하다. 일반적으로 변압기나 비상발전기로부터 전동기까지의 거리가 짧으며 전동기용량이 작아 기동에 대한 어려움이 없으나 산업설비 등에 많이 이용되는 대용량 전동기의 기동특성에 대한 이론과 실제의 운전특성을 측정 분석하였다. 따라서 이번 연구는 전동기 기동 시 속도와 토크에 관계와 대용량 전동기 기동을 위한 분석과 전동기 기동 해석에 대해 연구하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2012년도 추계학술대회 논문집
• /
• pp.31-32
• /
• 2012

This paper presents a new design of magnetic bearing structure for application in Nuclear Power Plant (NPP). The proposed design includes so-called saturated coils which is used to generate the bias flux for bearing almost the whole mass of the rotor, and so-called linear auxiliary coil controlled to stabilize the suspension. The saturated coil is considered as an special electromagnet which is controlled to operate in the region of magnetic saturation in order to minimize the bias current as well as to enhance the magnetic flux density. This strategy will result in a very compact size of magnetic bearing as well as increasing the speed of the response of the current controller. The novel structure is expected to be applied to design very high power gas turbine generator of next generation of fast reactor in which the mass of rotor can reach 50 tons. The total power of the NPP can reach 2,000 MW. Moreover, the issue of arc occurrence between coils is also discussed and two solutions are proposed.

• 전기학회논문지P
• /
• 제51권2호
• /
• pp.60-67
• /
• 2002

This paper presents a control approach for designing a self tuning fuzzy controller for a synchronous generator excitation and SVC system. A combination of thyristor-controlled reactors and fixed capacitors (TCR-FC) type SVC is recognized as having the most flexible control and high speed response, which has been widely utilized in power systems, is considered and designed to improve the response of a synchronous generator, as well as controlling the system voltage. The proposed parameter self tuning algorithm of fuzzy controller is based on the steepest decent method using two direction vectors which make error between inference values of fuzzy controller and output values of the specially selected PSS reduce steepestly. Using input-output data pair obtained from PSS, the parameters in antecedent part and in consequent part of fuzzy inference rules are learned and tuned automatically using the proposed steepest decent method. The related simulation results show that the proposed fuzzy controller is more powerful than the conventional ones.

• 제어로봇시스템학회논문지
• /
• 제22권7호
• /
• pp.513-518
• /
• 2016

The piezoelectric actuating device is known for its large power density and simple structure. It can generate a larger force than a conventional actuator and has also wide bandwidth with fast response in a compact size. To control the piezoelectric actuator, we need an analog signal conditioning circuit as well as digital microcontrollers. Conventional microcontrollers are not equipped with an analog part and need digital-to-analog converters, which makes the system bulky compared with the small size of piezoelectric devices. To overcome these weaknesses, we are developing a single-chip controller that can handle analog and digital signals simultaneously using mixed-signal FPGA technology. This gives more flexibility than traditional fixed-function microcontrollers, and the control speed can be increased greatly due to the parallel processing characteristics of the FPGA. In this paper, we developed a floating-point multiplier, PWM generator, 80-kHz power control loop, and 1-kHz position feedback control loop using a single mixed-signal FPGA. It takes only 50 ns for single floating-point multiplication. The PWM generator gives two outputs to control the charging and discharging of the high-voltage output capacitor. Through experimentation and simulation, it is demonstrated that the designed control loops work properly in a real environment.

• 전기학회논문지
• /
• 제65권6호
• /
• pp.987-994
• /
• 2016

In this paper, we present a comparative analysis of surface-mounted permanent magnet synchronous motors (SPMSM) and interior permanent magnet synchronous motors (IPMSM). First, we use 2D finite element analysis (FEA) to analyze models satisfying the same rated conditions according to the torque-speed curve characteristics, which are determined from the operating conditions. Next, we manufacture an SPMSM and IPMSM having good performances from an electromagnetic perspective based on analysis results, namely the cogging torque, torque ripple, and efficiency. We analyze both of the manufactured machines when they are connected back-to-back and when they are used as a motor and a generator, respectively. The motor is driven by a commercial inverter and the generator is connected to a three-phase resistance load bank. Finally, based on experimental results, which include the total harmonic distortion (THD) of the back electro-motive force (EMF), cogging torque, efficiency, and mass, we determine the motor that is most suitable under requirements.

• 화약ㆍ발파
• /
• 제17권4호
• /
• pp.32-50
• /
• 1999

This study deals with interface charactristics of tube and tubesheet of the nuclear steam generator by the explosive expansion in order to take advantage of optimum expansion ratio, pull-out strength and leakage tightness and improvement of the resisitance on the stress corrosion cracking for low residual stress. The paper also show the relationship between roll, hydraulic and explosive expansion. The results obtain are as follows (1) Because of the explosive bonding is to use the high speed pressure and energy by the explosive, workability is good, bonding region is homogenous (2) Expansion ratio is 2.7%, Pull-out strength 850kg, Leakage strength $500kg/cm^2$. Clearance gap is 10~30mm in case of explosive expansion and interface structure of the tube and tubesheet is optimum condition. (3) As the transition region of the explosive expansion is inactive, the resistance of the stress corrosion cracking is increases 30~40% compare to the roll and hydraulic expansion.

• International Journal of Precision Engineering and Manufacturing
• /
• 제9권4호
• /
• pp.74-78
• /
• 2008

High-speed tool steels are extensively used in tooling industries for manufacturing cutting tools, forming tools, and rolls. Electrical discharge machining (EDM) has been found to be an effective process for machining these extremely hard and difficult-to-cut materials. Extensive research has been conducted to identify the optimum machining parameters for EDM with different tool steels. This paper presents a fundamental study of the surface characteristics of SKH-51 tool steel machined by micro-EDM, with particular focus on obtaining a better surface finish. An RC pulse generator was used to obtain a better surface finish as it produces fine discharge craters. The main operating parameters studied were the gap voltage and the capacitance while the resistance and other gap control parameters were kept constant. A negative tungsten electrode was used in this study. The micro-EDM performance was analyzed by atomic force microscopy to determine the average surface roughness and the distance between the highest peak and lowest valley. The topography of the machined surface was observed using a scanning electron microscope and a digital optical microscope.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제8권4호
• /
• pp.375-385
• /
• 2016

Given the rapid progress made in understanding the dynamics of an offshore floating body in an ocean environment, the present study aimed to simulate ocean waves in a small-sized wave flume and to observe the motion of a cylindrical floating body placed in an offshore environment. To generate regular ocean waves in a wave flume, we combined a wave generator and a wave absorber. In addition, to precisely visualise the oscillation of the body, a set of light-emitting diode illuminators and a high-speed charge-coupled device camera were installed in the flume. This study also focuses on the spectral analysis of the movement of the floating body. The wave generator and absorbers worked well to simulate stable regular waves. In addition, the simulated waves agreed well with the plane waves predicted by shallow-water theory. As the period of the oncoming waves changed, the movement of the floating body was substantially different when tethered to a tension-leg mooring cable. In particular, when connected to the tension-leg mooring cable, the natural frequency of the floating body appeared suddenly at 0.391 Hz as the wave period increased.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2010년도 춘계학술대회
• /
• pp.507-511
• /
• 2010

Digital radio frequency memory (이하 DRFM)은 입력되는 RF신호를 저장 후 필요한 시점에 입력된 RF신호로 복원하여 출력하는 기능을 가진 장치로써 Jammer, EW시뮬레이터, Target Echo Generator 등 사용되는 분야가 광범위하다. 본 논문에서는 고주파 입/출력모듈, 국부 발진모듈로 구성된 고주파부와 디지털 처리부로 이루어진 DRFM의 하드웨어적 구현 방안을 제안한다. 그리고 펄스형태의 RF신호를 양자화하는 ADC(A/D conversion), 이 데이터를 저장하고 재생신호를 생산하는 FPGA와 RF 신호를 생산하는 DAC(D/A conversion)로 구성되는 디지털 처리부에서 복제된 신호 생성방안을 제안한다. 이렇게 제안된 방안을 적용하여 제작한 후 모의 신호를 입력하여 얻은 시험결과를 통하여 이 제안방안의 타당성을 확인한다.