• Journal of the Korean Ceramic Society
• /
• v.36 no.8
• /
• pp.813-819
• /
• 1999

Inner crack-like pores with controlled amount of Ca impurity level in the high purity alumina single crystal sapphire had been created by micro-fabrication technique which includes ion implantation photo-lithography Ar ion milling and hot press technique. The morphological change and the healing of crack-like pore in the Ca doped high purity single crystal alumina during high temperature heat treatment in vacuum were observed using optical microscopy. The hexagonal bridging ligaments were developed and the size of hexagonal bridging ligaments had been increased with temperature and Ca amount and had grown to their corner rounded. It appeared that the hexagonal bridging ligaments would have an equilbrium size with temperature and the amount of Ca addition. Three kinds of crack-like pore healing type were observed. Edge regression and ligament growth were observed from relatively low temperature in the crack-like pore. Edge regression were found in almost all of the crack-like pore but the ligament growth were found only in the several crack-like pores accelerating heating very fast. Flow type healing was observed above $1800^{\circ}C$ and It healed the crack-like pore very slowly.

• Journal of Powder Materials
• /
• v.26 no.4
• /
• pp.282-289
• /
• 2019

Ti has received considerable attention for aerospace, vehicle, and semiconductor industry applications because of its acid-resistant nature, low density, and high mechanical strength. A common precursor used for preparing Ti materials is $TiCl_4$. To prepare high-purity $TiCl_4$, a process based on the removal of $VOCl_3$ has been widely applied. However, $VOCl_3$ removal by distillation and condensation is difficult because of the similar physical properties of $TiCl_4$ and $VOCl_3$. To circumvent this problem, in this study, we have developed a process for $VOCl_3$ removal using Cu powder and mineral oil as purifying agents. The effects of reaction time and temperature, and ratio of purifying agents on the $VOCl_3$ removal efficiency are investigated by chemical and structural measurements. Clear $TiCl_4$ is obtained after the removal of $VOCl_3$. Notably, complete removal of $VOCl_3$ is achieved with 2.0 wt% of mineral oil. Moreover, the refined $TiCl_4$ is used as a precursor for the synthesis of Ti powder. Ti powder is fabricated by a thermal reduction process at $1,100^{\circ}C$ using an $H_2-Ar$ gas mixture. The average size of the Ti powder particles is in the range of $1-3{\mu}m$.

• Journal of Microbiology and Biotechnology
• /
• v.21 no.1
• /
• pp.43-49
• /
• 2011

As a rare sugar alcohol, L-arabitol can be used in food and can prevent extra fat deposits in the intestinal tract. Commercially, L-arabitol is prepared from pure L-arabinose by hydrogenation, which needs a high temperature and high pressure, leading to a high production cost for Larabitol. Therefore, this study describes a novel L-arabitol production method based on biological purification from the xylitol mother liquor, a cheap and readily available raw material that contains a high concentration of Larabitol. First, a novel Bacillus megaterium strain was screened that can utilize xylitol, sorbitol, and mannitol, yet not L-arabitol. The isolated strain was inoculated into a medium containing the xylitol mother liquor under formulated culture conditions, where a high L-arabitol yield (95%) and high purity (80%) were obtained when the medium was supplemented with 50 g/l of xylitol mother liquor. Upon further purification of the fermentation broth by ion exchange and decolorization, L-arabitol was crystallized with a purity of 98.5%.

• Journal of Korea Foundry Society
• /
• v.14 no.6
• /
• pp.520-529
• /
• 1994

This study describes the influence of the trace amount of sulphur on the nucleation behavior of graphite crystals in high purity Fe-C-Si alloys prepared by levitation melting method. Detailed microstructural analyses of high purity(HP) and sulphur added(HP＋S) samples showed that the nucleation of graphite crystals was prevented by sulphur. With decreasing the sulphur content, the shape of graphite crystals tended to spherulitic, and below 2ppm S, that of graphite crystals was only nodular. The critical cooling rate for the nucleation of griphite crystals was calculated as $1.5{\times}10^3k/s$. It is obvious from this work that residual C-C clusters act as an effective nucleation site for graphite crystals and one of the important role of nodularizing elements is to act as scavenger which removes harmful impurities from the solution.

• Transactions of the Korean hydrogen and new energy society
• /
• v.16 no.3
• /
• pp.290-295
• /
• 2005

For the application of fuel cell, the content and concentration of impurities in hydrogen stream must be classified. The purpose of this study is to provide analysis tool for the determination of impurities in hydrogen with ultra high purity. To produce UHT hydrogen, we purified hydrogen gas by both getter-based catridge and liquid-nitrogen soaked catridge. We compare two methods and propose new method to know about what is in hydrogen stream.

• Progress in Superconductivity and Cryogenics
• /
• v.3 no.1
• /
• pp.69-73
• /
• 2001

For developing the cryogenic air separation unit, it requires some technology such as basic process design. equipment design and manufacturing based on the cryogenic physical properties and separation theory. In this study, we developed a process and equipment for producing high purity nitrogen which has the production capacity of 1600N㎥/h under 1 ppm $O_2$ and $H_2O$. Also we found that the number of theoretical plate(NTP) of distillation column was 44 and maximum nitrogen recovery ration of this process was 42% from the process simulation. The performance test was also carried out for the nitrogen recovery ratio and equipment efficiency. The results showed that the optimum nitrogen recovery was 41% and the maximum equipment efficiency was attained.

• 한국생물공학회:학술대회논문집
• /
• 2005.04a
• /
• pp.351-354
• /
• 2005

A new isolation and purification method was developed aiming at increasing yield and purity for homoharringtonine. This method was a simple andefficient procedures, for the isolation and purification of homoharringtonine from Cephalotaxus koreana, consisting of solvent extraction, adsorbent treatment, low-pressure chromatography, and high performance liquid chromatography (HPLC). The crude homoharringtonine was efficiently pre-purified adequately to perform HPLC through a combination withadsorbent treatment and low-pressure chromatogaphy. The homoharringtonine can be simply obtained with high purity and yield from crude homoharringtonine by HPLC. Purified homoharringtonine was characterized.

• Journal of the Korean Ceramic Society
• /
• v.15 no.2
• /
• pp.89-97
• /
• 1978

The basic mechanism of adherence in sintered high purity alumina ceramic-to-metal bonding was studied. Emphasis was placed on flux composition, porosity of the fired ceramics, and metallizing mixtures. The study was conducted on 95 and 99.5% alumina, using molydbenum-manganese, molybdenum-manganese-silicon dioxide metallizing compositions. Metallizing was performed in wet hydrogen (dew point, ＋17$^{\circ}C$) at 145$0^{\circ}C$ for 45min. This experiment indicated that adhernece mechanism of ultra high purity alumina ceramic was attributed to formation of $MnAl_2O_$4, and in the case of 95% alumina containing glass, the migration of glass from the interface into the void of the metal coating was the main role to the adhrence. It showed also that greater the bond-strength was resulted as porosity was increased.

• Journal of the Korean Ceramic Society
• /
• v.24 no.5
• /
• pp.431-436
• /
• 1987

High purity Al2O3 has been extracted from serlcite of clayminerals, selicite was treated by H2SO4(2N∼18N) solution, NH4OH treatment(PH8.5∼10.0) and metallic impurities such as Fe were removed by NaOH treatment. The tendency of extraction yield of ${\alpha}$-Al2O3 have been investigated by relating reaction time, acid concentration. Reaction products were analyzed by DT-TGA, chemical analysis and X-ray diffractometer. Prepared ${\alpha}$-Al2O3 power is fired in air at 1400$^{\circ}C$, 1600$^{\circ}C$ 2hr. The results are as follows; 1. The most suitable extracting conditions of ${\alpha}$-Al2O3 from Selicite were N-H2SO4, 120 min acidtreating time. 2. The optimum pH condition was 9.0. 3. Physical properties of sintered Al2O3 bodies were as follows. Relative density is 99%. Water absorption is 0.26%. Rock well hardness is 89.

• Journal of the Korean Ceramic Society
• /
• v.30 no.5
• /
• pp.420-426
• /
• 1993

The machinability of ceramics has been experimentally studied. The experiments were conducted on alumina cernmics of various purity, quartz, and cordierite using the sintered diamond tools and CBN tools. Tool wasre, surface roughness, and cutting resistence were measured and analysed. It was found that the workpieces could be machined with the diamond and CBN tools, but the sintered diamond tools were more efficient for the machining of the high strength ceramics. The machining of alumina ceramics with sintered diamond tools showed that (1) wet machining prolonged tool life comparing with dry machining, (2) workpiecewith higher purity had better surface roughness, (3) severe cutting conditions led to the chipping and fracture of tool and increase of the surface roughness and cutting resistance, (4) 20~40m/min of cutting speed, 0.01~0.02mm/rev of feed, and 0.1~0.2mm of cutting depth are suggested as proper cutting conditions for the high strength ceramics.