• 한국안전학회지
• /
• 제29권5호
• /
• pp.1-6
• /
• 2014

When the fluid energy convert into kinetic energy due to water hammer, the propagation velocity of pressure wave appear. The propagation velocity of pressure wave(1050 m/s) of very fast could be damage to the pipeline system. If the occurrence of water hammer is due to down-pressure, the faster the air exhaust or supply device is needed. it is high Speed Air Valve. In this paper, Each 3.12, 3.13, 3.72, $3.74kg/cm^2$ pipeline pressure were setting, and then executed pressure rapid drop for obtaining a high Speed Air Valve Operating time and pressure change data. the result was that pipe line pressure stabilization time were each 0.98, 1, 1.22, 1.25 sec. In other words, that pressure drop experimental results pipe line pressure was equal to atmospheric pressure without negative pressure After about one second. The study result would be useful to pipe line system stability design because this data could be foresee pressure stabilization time.

• 한국안전학회지
• /
• 제32권4호
• /
• pp.129-136
• /
• 2017

This study investigated the probability of possible accident through qualitative and quantitative analysis of the pressure safety valve types installed in facilities using high pressure gas to compare the installation domestic and foreign pressure safety valve standards sought the safety characteristics and safety improvement direction accordingly. The three types are the case where the shut-off valve is not installed at the front of the PSV (Case A), If a shut-off valve is installed at the front of the PSV for inspection (Case B) and If a shut-off valve is installed in front of PSV (C.S.O), PSV is installed in parallel (Case C). Three types of cases were compared with FTA and HAZOP. The results of study of the possible accidents due to over-pressure safety valve installation type, used in a high-pressure gas facilities was shows in the following order Case B > Case A > Case C. The results of analysis through FTA was in order to protect the reservoir for the possible occurring of accident the safety valve installation is depend on its type. In the FTA analysis, defects in the device itself which attached to the storage tank as a substitute for analysis of the probability of operator mistakes was Case B with as high as $2.01{\times}10^{-6}$. Depending on the type of installation analysis of Case B in order to ensure safety is prohibited to install shut-off valve and believes that mandatory regulations are needed. Rationally installing of pressure safety valve in the high pressure using facilities will be expected to improve the industrial safety from severe accidents such as high-pressure gas fire explosion.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2000년도 춘계학술발표회 초록집
• /
• pp.5-5
• /
• 2000

In the severe accident case like LOCA, Zircaloy(Zry) claddings are oxidized not only in high temperature but also in high pressures. It is a concem whether the safety of high bum up fuels can be maintained during severe accident. The effects of steam pressure on Zry-4 oxidation, and the effect of prc-existing oxide layer on the cladding in the high temperature-high pressure oxidation of Ziy-4 were investigated. The experimental temperature range was $700-900^{\circ}C$, and the pressures were between 0.1 and l5.0MPa. Partial pressure of steam tumed out to be the important one rather than total gas pressure. The higher the steam pressure was applied, the thicker the oxide became. nle effect of st,earn pressure on the oxidation of claddings with preexisting oxide was about 40-60% less effective than that of pickled cladding. Aocelerated oxidation in highpressure slean1 seems to be originated from the formation of microcracks produced during the transformation of tetragonal zirconia to monoclinic phase. Steam pressure seems to affect the stability of tetragonal phase.

• 한국전기전자재료학회논문지
• /
• 제16권9호
• /
• pp.790-794
• /
• 2003

This paper describes the fabrication and characteristics of ceramic thin film type pressure sensors based on Ta-N strain gauges for high temperature applications. Ta-N thin-film strain gauges are deposited onto a thermally oxidized Si diaphragm by RF sputtering in an argon-nitrogen atmos[here($N_2$ gas ratio: 8%, annealing condition: 90$0^{\circ}C$, 1 hr.), patterned on a wheatstone bridge configuration, and used as pressure sensing elements with a high stability and a high gauge factor. The sensitivity is 1.097 ～ 1.21 mV/Vㆍkgf/$\textrm{cm}^2$ in the temperature range of 25 ～ 200 $^{\circ}C$ and the maximum non-linearity resistance), non-linearity than existing Si piezoresistive pressure sensors. The fabricated ceramic thin-film type pressure sensor is expected to be usefully applied as pressure and load sensors that os operable under high-temperature.

• 한국해양공학회지
• /
• 제27권6호
• /
• pp.106-111
• /
• 2013

In this study, numerical simulations and performance evaluation has been carried out to investigate performance characteristics of air-type high pressure piston pump. ANSYS and CFX were applied for analyzing the structure and flow behavior of air-type high pressure piston pump, respectively. The performance evaluation of high pressure piston pump was performed experimentally, the results were compared with simulation. It was found that the freezing phenomenon was improved by 20% and the pressure fluctuation decreased by 50%, compared with the previous pump.

• Geomechanics and Engineering
• /
• 제16권1호
• /
• pp.71-83
• /
• 2018

Compacted bentonites were chosen as the backfill material and buffer in high level nuclear waste disposal due to its high swelling pressure, high ion adsorption capacity and low permeability. It is essential to estimate the swelling pressure in design and considering the safety of the nuclear repositories. The swelling pressure model of expansive clay colloids was developed based on Gouy-Chapman diffuse double layer theory. However, the diffuse double layer model is effective in predicting low compaction dry density (low swelling pressure) for certain bentonites, and invalidation in simulating high compaction dry density (high swelling pressure). In this paper, the new relationship between nondimensional midplane potential function, u, and nondimensional distance function, Kd, were established based on the Gouy-Chapman theory by considering the variation of void ratio. The new developed model was constructed based on the published literature data of compacted Na-bentonite (MX80) and Ca-bentonite (FoCa) for sodium and calcium bentonite respectively. The proposed models were applied to re-compute swelling pressure of other compacted Na-bentonites (Kunigel-V1, Voclay, Neokunibond and GMZ) and Ca-bentonites (FEBEX, Bavaria bentonite, Bentonite S-2, Montigel bentonite) based on the reported experimental data. Results show that the predicted swelling pressure has a good agreement with the experimental swelling pressure in all cases.

• 한국화재소방학회논문지
• /
• 제31권5호
• /
• pp.63-69
• /
• 2017

본 연구에서는 초고압 펌프의 개발과 같이 사용할 수 있는 초고압용 장거리 호스 개발에 관한 연구이며, 접근과 방수거리의 도달이 어려운 초고층 건물 및 대심도 터널의 화재진압에 효율적으로 적용이 가능함과 동시에 축광 성능을 포함하여 소방관의 화재 진압 시 퇴로 확보에도 도움이 될 수 있는 초고압용 호스의 개발에 관한 연구이다. 호스의 성능으로서 압력 3 MPa, 유량 2000 lpm을 목표로 초고압 호스를 개발하였으며, 2중의 자켓과 3중의 폴리우레탄 코팅 및 52의 경사를 사용하여 매우 촘촘하고 높은 고압에도 견딜 수 있는 초고압 소방호스를 개발하였다. 개발된 초고압 호스의 성능을 확보하기 위하여 구조 및 외관, 고압에서의 누수, 길이, 신장률, 박리시험, 마찰시험, 파단압시험 및 자유낙하 시험 등이 공인된 인증기관에서 수행되었으며 수행결과 성능에 이상이 없는 것으로 파악되었다. 또한 소방관의 화재진압 시 퇴로를 확보하기 위한 축광 성능의 초고압 호스에 추가하여 연구 및 개발하였으며, 휘도시험의 값으로 축광의 발광시험 개시부터 40분 후까지 휘도 측정치가 휘도시험의 기준 값 이상으로 충분히 확보되는 것을 확인할 수 있었다. 향후, 이와 같은 초고압용 소방용 호스가 상용화가 되어 현장에서 적용된다면 초고층 건물의 화재진압 및 장대터널에서의 화재진압에 있어서 현재 사용되고 있는 소방호스 보다 개선된 화재 진압 및 안전한 퇴로를 확보하는 측면에서 기여할 수 있을 것으로 판단된다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2664-2669
• /
• 2008

Feedwater heaters of many nuclear power plants have recently experienced severe wall thinning damange, which will increase as operating time progresses. Several nuclear power plants in Korea have experienced wall thinning damage in the area around the impingement baffle-installed downstream of the high pressure turbine extraction stream line- inside number 5A and 5B feedwater heaters. At that point, the extracted steam from the high pressure turbine is two phase fluid at high temperature, high pressure, and high speed. Since it flows in reverse direction after impinging the impingement baffle, the shell wall of the number 5 high pressure feedwater heater may be affected by flow-accelerated corrosion. This paper describes operation of experience and numerical analysis composed similar condition with real high pressure feedwater heater. This study applied squared, curved and new type impingement baffle plates to feedwater heater same as previous study. In addition, it shows difference of pressure distribution and value between single phase and two phase based on experience and numerical analysis.

• 한국자동차공학회논문집
• /
• 제6권5호
• /
• pp.162-173
• /
• 1998

The high pressure common rail injection system offers a high potential for improving emmisions and performance characteristics in large direct diesel engines. High pressures in the common rail with electronic control allows the fuel quantity and injection timing to be optimized and controlled throughout a wide range of engine rpm and load conditions. In this study, high pressure supply pump, common rail, pipes, solenoid and control chamber, and nozzle were modeled in order to predict needle lift, rate of injection, and total injected fuel quantity. When the common rail pressure is raised up to 13.0 ㎫ and the targer injection duration is 1.0ms, the pressure drop in common rail is about 5.0㎫. The angle of effective pressurization is necessary to be optimized for the minimum pump drive torque and high pressure in common rail depending on the operating conditions. The characteristics of injection were also greatly influenced by the pressures in common rail, the areas of the inlet and exit orifice of the control chamber.

• 한국기계가공학회지
• /
• 제11권6호
• /
• pp.55-61
• /
• 2012

In this study, it was grasped to the flow characteristics of injection nozzle installed in high pressure holder for improving productivity. Chip curling occurred during cutting process for difficult-to-cut material detracts product qualities and productivity. Among of method preventing the phenomenon, high pressure injecting cutting oil is an alterative. In this study, the optimal nozzle was designed by CFD method and it was conducted to analyse on the effect of high pressure injection on chip shape generated during cutting process and wear of insert by experimental method. As the result, it could be confirmed that high pressure injection is favorable for preventing chip curling and insert from wearing.