• Korean Journal of Optics and Photonics
• /
• v.28 no.4
• /
• pp.153-157
• /
• 2017

An infrared camera and laser common-path optical system is applied to DIRCM (directional infrared countermeasures), to increase boresighting accuracy and decrease weight. Thermal effects of a laser beam in a common-path optical system are analyzed and evaluated, to predict any degradation in image quality. A laser beam with high energy density is absorbed by and heats the optical components, and then the surface temperature of the optical components increases. The heated optical components of the common-path optical system decrease system transmittance, which can degrade image quality. For analysis, the assumed simulation condition is that the laser is incident for 10 seconds on the mirror (aluminum, silica glass, silicon) and lens (sapphire, zinc selenide, silicon, germanium) materials, and the surface temperature distribution of each material is calculated. The wavelength of the laser beam is $4{\mu}m$ and its output power is 3 W. According to the results of the calculations, the surface temperature of silica glass for the mirror material and sapphire for the lens material is higher than for other materials; the main reason for the temperature increase is the absorption coefficient and thermal conductivity of the material. Consequently, materials for the optical components with high thermal conductivity and low absorption coefficient can reduce the image-quality degradation due to laser-beam thermal effects in an infrared camera and laser common-path optical system.

• Clean Technology
• /
• v.14 no.3
• /
• pp.171-175
• /
• 2008

The effect of the addition of $Al^{3+}$ dopant on the electrochemical characteristics of $Li_{4}Ti_{5}O_{12}$ was investigated. $Li_{4}Ti_{5}O_{12}$ is known as a 2ero-strain material, and $Li_{3.95}Al_{0.15}Ti_{4.9}O_{12}$ has been manufactured by solid-state reaction with high energy ball milling (HEBM). The samples were heated at 800, 900 and $1000^{\circ}C$ in electric furnace. The structural and surface structures were measured by XRD (X-ray diffraction) and SEM (scanning electron microscopy). Cut-off voltage of charge/discharge cycles was $1.0{\sim}3.0 V$ to investigate reversible capacity, cycle stability and plateau voltage. The reversible capacity of $Li_{3.95}Al_{0.15}Ti_{4.9}O_{12}$ was 138 mAh/g.

• Korean Journal of Agricultural Science
• /
• v.22 no.1
• /
• pp.103-109
• /
• 1995

The model foods were prepared by simulating mositure, protein and starch, and they were heated for 30 mins, at $80^{\circ}C$ and then cooled at $25^{\circ}C$ in water bath. Their rheological properties were investigated by the use of Brookfield wide-gap rotational viscometer at $30{\sim}60^{\circ}C$, and the rotation speed ranged from 0.6 to 6 rpm and solid content ranged from 8% to 11%, the results obtained were as follows. 1. All the model foods ($P_1S_3$, $P_2S_2$, $P_1S_1$, $P_2S_1$, $P_3S_1$, $P_4S_0$) exhibited pseudoplastic behaviors with yeild stress and were thixotropic foods which showed time - dependent structural decays, but the starch food of 8 ~ 11 % solid content did not show the flow behavior. 2. The correlation between the rheological parameters and the protein content of model foods in various moisture content did not appeared a constant relationship. 3. The change of shear stress against shear rate in high starch foods was larger than that in high protein foods and the structure at initial shear time was decayed with a quatic equation according to the Tiu's Model and structural decay was in parallel with the increase of shear rate. 4. The temperature dependency of the apparent viscosity of $P_1S_2$, and $P_2S_1$ was fully expressed by Arrhenius equation and activation energies of their food were 2.35 and $1.34Kcal/g{\cdot}mol$, respectively.

• Korean Journal of Food Science and Technology
• /
• v.44 no.4
• /
• pp.478-483
• /
• 2012

In order to evaluate the microbial safety of the foodstuffs and manus in regards to foodservice operations, the total of 1,051 samples of drinking waters, vegetables, and cooked foods were collected. Total viable count (TVC), coliform group, and pathogens were analyzed. Twenty five percent samples of 441 drinking waters showed high contamination of above 2 log CFU/g TVC. Twenty percent of the waters were contaminated by above one log CFU/g coliform. Forty percent of non-heated food, Moochim, were contaminated by above 5 log CFU/g TVC and 26% of Moochim were contaminated by above 2 log CFU/g coliform. Bacillus cereus and Eschericia coli were detected on boiled rice and kimchi, and B. cereus was detected with a high ratio. Therefore, the foodstuffs and manus regarding foodservice operations appear to be generally safe. However, efficient microbial control for drinking water and Moochim-style food is necessary and in particular, careful management to reduce microbial contamination should be applied to drinking water.

• Journal of the Korean Electrochemical Society
• /
• v.14 no.1
• /
• pp.16-21
• /
• 2011

$Li_4Sn_xTi_{5-x}O_{12}$ was manufactured by high energy ball milling (HEBM) and used as an anode material for lithium ion battery. Various amount of $SnO_2$was added to $Li_4Ti_5O_{12}$ and heated at different temperatures. The purpose of this research was to see the effect of $SnO_2$ addition into $Li_4Ti_5O_{12}$. Manufactured samples were analyzed by TGA, XRD, SEM, PSA. Battery cycler was used to test the charge/discharge properties of active materials. Heat treatment temperature of $800^{\circ}C$ was needed to make a stable structure of $Li_4Sn_xTi_{5-x}O_{12}$ and the particle size distribution was $0.2{\sim}0.6\;{\mu}m$. Charge/discharge process was repeated for 50 cycles at room temperature. The initial capacity was 168mAh/g and the voltage plateau was observed at 1.55V(Li/$Li^+$).

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.32 no.3
• /
• pp.96-102
• /
• 2022

Hydroxyapatite (HAp) was synthesized from calcium hydroxide (Ca(OH)₂) reacting with phosphoric acid (H₃PO₄) in aqueous solution. HAp powders were synthesized from extremely high concentration of precursor solutions over 3 M of Ca(OH)₂ aqueous suspension using modified process parameters such as phosphoric acid (H₃PO₄) pouring rate, aging time and post ball milling process. Regardless of phosphoric acid pouring rate, the DCPD (dicalcium phosphate dihydrate) was formed at room temperature and when heated above 700℃, β-TCP (tricalcium phosphate) was synthesized and the amount reached its maximum at 900℃. When the synthesized powder was sintered at 1150℃, β-TCP, a high temperature impurity phase, remained. The single HAp phase without DCPD was obtained from post ball-milled precipitates followed by 3 day aging. For the ball-milled precipitates even without the aging process, the desired single HAp phase without β-TCP could be obtained by heat treatment above 500℃. The post ball milling process provided a convenient route for HAp synthesis.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.55 no.6
• /
• pp.817-826
• /
• 2022

This study was conducted to determinean optimal soaking solution for inhibiting the texture softening of shrimp Litopenaeus vannamei pressured at high temperature (S-P/HT) in a retort, and also to optimize concentrations of 0.5% calcium chloride (CC) and 5.0% potato starch (PS) for preparation of a mixed solution (MS) and soaking time (ST) in the MS. On the basis of the results of expressible drip (4.6%), water holding capacity (95.1%), hardness (18.4 N/cm²) and sensory texture (7.2 score), the MS was found to be the optimal soaking solution for inhibition of texture softening under S-P/HT conditions, The concentrations of CC (X₁, %), PS (X₂, %), and ST (X₃, min) were selected as independent variables, and hardness (Y₁), springiness (Y₂) and sensory texture (Y₃) were selected as dependent variables. The optimal conditions of X₁, X₂, and X₃ were 0.51%, 6.34%, and 364 min, respectively. Under the optimal conditions, the experimental values of Y₁, Y₂ and Y₃ were 18.3±0.8 N/cm², 4.4±0.3 mm and 7.7±0.2, respectively, which did not diffr significantly from the predicted values (P>0.05). In conclusion, the optimized models of X₁, X₂, and X₃ for the preparation of S-P/HT using CC-PS were suitably fitted.

• Journal of Life Science
• /
• v.32 no.9
• /
• pp.667-677
• /
• 2022

Dolsan mustard seeds (DMS) were added in whole, crushed, and roasted form at 0.5 g (S-1), 1.0 g (S-2), and 1.5 g (S-3), respectively to broth and heated for 10 or 15 min. After cooling, the quality characteristics were measured. Salinity and pH decreased with boiling time. The antioxidant activities of the experimental broth were measured in terms of total polyphenol content, total flavonoid content, electron donating ability (EDA), 2,2-azino-bis (3-ethyl-benzothizoline-6-sulfonic acid) (ABTS) radical scavenging activity, and ferric reducing antioxidant power (FRAP). The overall, antioxidant activity was higher in broths containing 1.0 g and 1.5 g DMS than in those containing 0.5 g DMS and the activity increased with increasing boiling time. Sinigrin was not detected in the control group, and no significant difference in sinigrin content was noted among broths containing different concentrations of DMS. A high glutamic acid content was detected in the control broth, whereas glutamic acid, aspartic acid, glycine, proline, alanine, and arginine were detected in the broths containing DMS. The free amino acid contents, particularly aspartic acid and glutamic acid contents, were high in umami. Volatile components, such as 2-propenyl-isothiocyanate (ITC), allylthiocyanate, n-butyl ITC, and 3-butenyl ITC, were detected in the DMS-containing broths. Sensory evaluation revealed that a higher amount of DMS added and a longer heating time increased the overall taste preference, and the difference was statistically significant. The purpose of this study was to present basic data on the quality characteristics of DMS-added broths to aid in the development of new products using DMS.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.15 no.4
• /
• pp.283-290
• /
• 1982

Sardine and mackerel so called dark muscled fish have been underutilized due to the disadvantages in bloody meat color, high content of fat, and postmortem instability of protein. Recent efforts were made to overcome these defects and develope new types of product such as texturized protein concentrates and dark muscle eliminated minced fish. Approach of this study is based on the rapid dehydration of foamed fish-starch paste by dielectric heating. In process comminuted sardine meat was washed more than three times by soaking and decanting in chilled water and finally centrifuged. The meat was ground in a stone mortar added Ivith adequate amounts of salt, foaming agent, and other ingredients for aid to elasticity and foam stability. The ground meat paste was extruded in finger shape and heated in a microwave oven to give foamed, expanded, and porous solid structure by dehydration. Dielectric onstant $(\varepsilon')$ and dielect.ic loss $(\varepsilon")$ values of sardine meat paste were influenced by wavelength and moisture level. Those values at 100 KHz and 15 MHz were ranged 2.25-9.86; 2.22-4,18 for E' and 0.24-19.24; 0.16-1.20 for E", respectively, at the moisture levels of $4.2-13.8\%$. For a formula for fish-starch paste preparation, addition of $20-30\%$ starch (potato starch) to the weight of fish meat, $2-4\%$ salt, and $5-10\%$ soybean protein was adequate to yield 4-5 folds of expansion in volume when heated. Addition of e99 yolk was of benefit to micronize foam size and better crispness. In order to provide better foaming and dehydration, addition of $0.2-0.5\%$sodium bicarbonate, foaming agent, was proper to result in foam size of 0.5-0.7 mm and foam density of $200-400\;/cm^2$ which gave a good crispness. Heating time was depended upon the moisture level of fish-starch paste. For a finger shaped paste (1.0cm. $D\times10cm.L$) heating for 150-200 sec. in a microwave oven (700W. 2.45GHz) was sufficient to generate foams, expand, and solidify the porous structure of fish-starch paste. When the moisture content was above $55\%$ browning and scorching was deepened due to over-expansion and over-heating whereas the crispness was hardened by insufficient expansion at lower moisture content. In quality evaluation of the product, chemical composition of $30\%$ starch and $3\%$ salt added product was moisture $8.8\%$, lipid $2.4\%$, carbohydrate $46.7\%$, protein $36.1\%$, and ash $6.0\%$. Eleven membered panel test evaluated that fish-starch paste was acceptable in color, crisp-ness, taste, except a trace of fishy odour which could be masked by the addition of spice extracts.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.24 no.2
• /
• pp.123-129
• /
• 1991

The skipjack and Alaska pollack meat were packed in square No. 3B can, and thermally processed at $121.1^{\cir}C$ so far as to reach Fo values of 5, 10 and 20, respectively. Also the another samples which were heated at $98^{\cir}C$ for 30 minutes were prepared. We have examined the changes of nitrogenous extractives and texture by thermal processing at high temperature in both fish meats. Moisture contents of both fish meats decreased slightly with the increasing of Fo values. When the samples were heated at $98^{\cir}C$ and $121.1^{\cir}C$, pH and VBN contents increased markedly in both fish meats; increasing ratio of pH and VBN contents in skipjack meat was larger than those of Alaska pollack meat. Histamine were detected in concentration of 6.1mg/100g, 0.1mg/100g in raw skipjack and Alaska pollack meat, 8.2mg/100g, 0.1mg/100g in Fo 20 samples of these fish meats, respectively. The contents of total free amino acids in skipjack and Alaska polack meat were 984.8mg/100g, 282.3mg/100g, and these total contents decreased slightly with increasing of Fo values. Little changes were observed in free amino acid composition, but only His, Tau, Ala in skipjack meat and Tau in Alaska pollack meat decreased significantly by heat treatment. Also the degredation of IMP were Proceeded during Preparation and heat treatment of samples, and TMAO changed into TMA almost equivalently. In changes of textures, as compared with heating of 98t for 30 minutes; Fo 5 heat treatment became more softened these fish meats.