• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.4
• /
• pp.223-231
• /
• 2012

The purpose of this study is to investigate basically the mechanism of heat transfer by the resolution of complex fluid flow inside a sophisticated designed screw dryer for the treatment of sewage sludge by using numerical analysis and experimental study. By doing this, the result was quite helpful to obtain the design criteria for enhancing drying efficiency, thereby achieving the optimal design of a multiple screw type dryer for treating inorganic and organic sludge wastes. One notable design feature of the dryer was to bypass a certain of fraction of the hot combustion gases into the bottom of the screw cylinder, by the fluid flow induction, across the delicately designed holes on the screw surface to agitate internally the sticky sludges. This offers many benefits not only in the enhancement of thermal efficiency even for the high viscosity material but also greater flexibility in the application of system design and operation. However, one careful precaution was made in operation in that when distributing the hot flue gas over the lump of sludge for internal agitation not to make any pore blocking and to avoid too much pressure drop caused by inertial resistance across the lump of sludge. The optimal retention time for rotating the screw at 1 rpm in order to treat 200 kg/hr of sewage sludge was determined empirically about 100 minutes. The corresponding optimal heat source was found to be 150,000 kcal/hr. A series of numerical calculation is performed to resolve flow characteristics in order to assist in the system design as function of important system and operational variables. The numerical calculation is successfully evaluated against experimental temperature profile and flow field characteristics. In general, the calculation results are physically reasonable and consistent in parametric study. In further studies, more quantitative data analyses such as pressure drop across the type and loading of drying sludge will be made for the system evaluation in experiment and calculation.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.7
• /
• pp.694-699
• /
• 2008

Considering the severe regulation associated with sludge treatment such as direct landfill and ocean dumping, there is no doubt in that an advanced study for the proper treatment of sludge is urgently needed in near feature. As one of viable method for sludge treatment, fry-drying of sludge by waste oil has been investigated in this study. The fundamental mechanism of this drying method lies in the phenomenon of rapid moisture escape in the sludge pore toward oil media. This is caused by the severe pressure gradient formed by the rapid oil heating between sludge and oil. As part of research effort of fry-drying using waste oil, a series of basic study has been made experimentally to obtain typical drying curves as function of important parameters such as drying temperature, drying time, oil type and geometrical shape of sludge formed. Based on this study, a number of useful conclusion can be drawn as following. The fry-drying method by oil immersion was found quite effective in the removal efficiency of sludge moisture, in general, the moisture content decreases significantly after 10 minutes and the whole moisture content was less than 5% after 14 minutes regardless of the drying temperature. The increase of oil temperature up to 140$^{\circ}C$ favors significantly for the removal of moisture but there was no visible difference above 140$^{\circ}C$. As expected, the decrease of diameter in sludge was efficient in drying due to the increased surface area per unit volume. Further, the effect of oil property by the change of oil type was noted. To be specific, for the case of engine oil the efficiency was found to be remarkably delayed in moisture evaporation compared with that of vegetable oil due to the increased viscosity of engine oil. It produced a result of increasing the evaporation of moisture largely relatively high in the drying temperature over 140$^{\circ}C$ compared with the drying temperature 120$^{\circ}C$ drying temperature as the drying time passed. Accordingly, the drying temperature is considered desirable as keeping over 140$^{\circ}C$ regardless of a sort of used oil.

• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.762-767
• /
• 2009

In this study, the feasibility of using vegetable oil extracted from tropical crop seed as a biodiesel feedstock was investigated by producing biodiesel and analysing the quality parameters as a transport fuel. In order to produce biodiesel efficiently, two step reaction process(pre-treatment and transesterificaion) was required because the tropical crop oil have a high content of free fatty acids. To determine the suitable acid catalyst for the pre-esterification, three kinds of acid catalysts were tested and sulfuric acid was identified as the best catalyst. After constructing the experimental matrix based on RSM and analysing the statistical data, the optimal pre-treatment conditions were determined to be 26.7% of methanol and 0.982% of sulfuric acid. Trans-esterification experiments of the pre-esterified oil based on RSM were carried out, then discovered 1.24% of KOH catalyst and 22.76% of methanol as the optimal trans-esterification conditions. However, the quantity of KOH was higher than the previously established KOH concentration of our team. So, we carried out supplemental experiment to determine the quantity of catalyst and methanol. As a result, the optimal transesterification conditions were determined to be 0.8% of KOH and 16.13% of methanol. After trans-esterification of tropical crop oil, the produced biodiesel could meet the major quality standard specifications; 100.8% of FAME, 0.45 mgKOH/g of acid value, 0.00% of water, 0.04% of total glycerol, $4.041mm^2/s$ of kinematic viscosity(at $40^{\circ}C$).

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.4
• /
• pp.323-332
• /
• 2010

Petroleum-based adhesive resins have extensively been used for the production of wood panels. However, it is necessary to develop environmentally friendly adhesive resins due to the increase of manufacturing cost and the environmental issue, such as the emission of volatile organic compounds, of the pertroleum-based adhesive resins. This study was conducted to formulate environmentally friendly adhesive resins using by rapeseed flour (RSF), which is the by-product of bio-diesel produced from rapeseed, for replacing petroleum-based adhesives with them. To formulate RSF-based adhesive resins, RSF was hydrolyzed in de-ionized water, 1% and 3% sodium hydroxide solutions. As a crosslinking agent, PF prepolymers were prepared with 1.8, 2.1 and 2.4 mol formaldehyde and 1 mol phenol (1.8-, 2.1- and 2.4-PF), and then mixed with RSF hydrolyzates to complete the formulation of RSF-based adhesive resins. The RSF-based adhesive resins were applied to fabricate 3-ply plywood panels. The solid content of RSF-based adhesive resins were ranged from 26.08% to 36.12% depending on the hydrolysis condition of RSF and PF prepolymer type with a high viscosity. The tensile shear strength and wood failure of plywood fabricated with RSF-based adhesive resins exceeded a minimum requirement of KS standard for ordinary plywood regardless of the hydrolysis condition of RSF and PF prepolymer type. Formaldehyde emissions of the plywood panels fabricated with 1.8-PF and RSF hydrolyzates were lower than that of E0 specified in the KS standard. Based on the results, RSF might be used as a raw material of environmentally friendly adhesives for the production of plywood panels, but further researches - the increase of solid content of RSF-based adhesives for reducing press time and the microscopic observation of plywood specimen for identifying the relationship between tensile shear strength and the penetration of adhesives into wood structure - are required to commercialize the RSF-based adhesives.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.1 no.1
• /
• pp.89-97
• /
• 2005

Recently, for the problem solution of demand and supply imbalance of fine aggregate due to the shortage of natural fine aggregate resource and the environment regulation on sea sand extraction in the construction field, the studies for the application of recycled fine aggregate using waste concrete are being progressed versatilely. On the other hand, the treatment of fly-ashes that of industrial by-product originated in the steam power plant is discussed by the continuous increasing of origination quantities. In the ease of using fly-ash, advantages are the improvement of workability, viscosity and long-time strength, and the reduction of hydration heat under the early ages, as the admixtures for concrete, but the studies for the application of fly-ash as recycled concrete admixtures are inadequacy. There fore, in this study, through investigating the properties of fresh, hardened and durability according to the replacement of recycled fine aggregate and fly-ash, it is intended to propose the fundamental data for structural application of recycled concrete using recycled fine aggregate and fly-ash. As the result of this study, they arc shown that the engineering properties and durability, in the case of replacement ratio 100% of recycled fine aggregate, arc similar to those of concrete using natural fine aggregate, so it is considered that recycled fine aggregate could be used as the fine aggregate for concrete. Also, the performances of recycled concrete are improved by replacing fly-ash.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.33 no.4
• /
• pp.653-660
• /
• 2006

Fuji VII is a glass-ionomer cement specially targeted for early protection in erupting first and second molars. Properties of Fuji VII such as very high level of fluoride release, low viscosity and no need to preliminarily etch the substrate would be useful to erupting molars with primary pit and fissure caries or hypoplastic area for preventive goal or remineralization. The purpose of this study were to evaluate remineralization of Fuji VII glass ionomer cement and to compare with one of other restorative materials such as conventional glass ionomer cement, resin-modified glass ionomer cement, compomer and composite resin. Forty-two extracted human molars were used for this study. All teeth were immersed in demineralizing solution for 48 hours after Class V cavity preparation was made on sound proximal surface. The teeth were randomly divided into six groups and restored with Fuji VII, Fuji II, Fuji II LC improved, F2000, $Filtek^{TM}$ Z250 and control group was unrestored. The middle area with $130{\pm}20{\mu}m$ thickness was separated from specimen using microtome and demineralized area was photographed under polarized microscope. Separated area was relocated to specimen and stored in artificial saliva, After four weeks, changes of demineralized area were observed and compared to them restorated immediately. The results from the this study can be summarized as follows ; 1. Fuji VII, Fuji II, Fuji II LC improved have more prominent remineralization effect than F2000, $Filtek^{TM}$ Z250, control group. 2. No significant differences in remineralization effect are seen between Fuji VII and Fuji II, Fuji II LC improved.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.61 no.3
• /
• pp.153-162
• /
• 2016

We investigated the physicochemical properties and starch structure of various rice varieties including 15 colored cultivars. NKHC showed the highest level of protein, lipid, and total dietary fiber levels. Reddish brown rice showed higher lipid content than that in black rice cultivars. Apparent amylose content of waxy and non-waxy colored rice varieties was within the range of 3~5% and 15~18%, respectively. IP exhibited the highest total starch (TS) content, whereas, NKHC and HJJ showed lower TS content than that in other cultivars. Pasting temperature of all colored rice cultivars, except IP, was about $68^{\circ}C$. Peak viscosity of IP, JJJ, Hong, and GGHM showed high values of 138, 130, 128, and 124, respectively. All the colored rice cultivars presented A-type X-ray diffraction pattern and polygonal shapes of starch granules were observed using scanning electron micrographs (SEM). Major groups of amylopectin chain lengths were B (12 < DP ${\leq}$ 24) and A (DP ${\leq}$ 12). SMHC showed the highest B chain content and the lowest A chain content (P < 0.05). These experimental results provided useful information for scientists and the food industry regarding colored rice starches.

• The Korean Journal of Food And Nutrition
• /
• v.30 no.1
• /
• pp.31-40
• /
• 2017

This study was undertaken to evaluate the quality characteristics and antioxidant characteristics of commercially available mixed grains in Korea. The quality characteristics of mixed grain products studied were the mixing ratio, water binding capacity, water solubility, swelling power, and pasting characteristics. The antioxidant characteristics assessed the total polyphenol, flavonoid contents, DPPH and ABTS radical scavenging activities. The mixing ratio of commercially available mixed grain products consisted of 5~25 kinds of grains, with maximum products containing 15-grain products. The water binding capacity, water solubility, and swelling power in commercially available mixed grain products were 99.83~122.83%, 6.91~39.26% and 7.76~86.92%, respectively. The peak, trough, breakdown, final and setback viscosity were $31.53{\pm}20.17RVU$, $25.24{\pm}13.22RVU$, $6.29{\pm}7.43RVU$, $50.27{\pm}25.84RVU$ and $18.74{\pm}8.68RVU$, respectively. Total polyphenol and flavonoid contents were $817.14{\sim}2,524.29{\mu}g\;GAE/g$ and $106.36{\sim}1,099.09{\mu}g\;CE/g$, respectively. The DPPH and ABTS radical scavenging activities were 31.91~151.70 mg TE/100 g and 28.09~119.92 mg TE/100 g, respectively. Products with high phenol content and radical scavenging activity were found to contain greater proportion of brown rice, colored rice, barley and soybean.

• Food Science of Animal Resources
• /
• v.27 no.2
• /
• pp.228-234
• /
• 2007

The purpose of this study was to investigate quality characteristics of the meat batter containing dietary fiber extracted rice bran. The formulations of meat batters were manufactured in a model system with 2% raw rice bran and 2, 4, 6% levels of dietary fiber extracted rice bran, respectively. The proximate compositions of dietary fiber extracted rice bran were 53.27% dietary fiber, 6.10% crude fat, 22.99% crude protein, 12.78% crude moisture, and 7.41% crude ash. Compared with control of uncooked meat batter, the pH value of all treatments were significantly different(p<0.05). The pH of cooked meat batter were similar to uncooked meat batter. $CIE\;L^*-\;and\;CIE\;b^*-value$ of uncooked meat batter containing dietary fiber extracted rice bran were lower than control, but CIE $a^*-value$ of treatment was higher than those in control(p<0.05). All treatments had significantly lower cooking loss and emulsion stability than control(p<0.05). Compared with control, viscosity of the treatments containing dietary fiber extracted rice bran were observed significantly higher than those in control (p<0.05). And then hardness, cohesiveness, gumminess, and chewiness of treatments were higher than in control(p<0.05). Conclusively, the results of this study showed that addition of dietary fiber extracted rice bran affected the high quality properties of meat batter.

• Journal of Food Hygiene and Safety
• /
• v.24 no.4
• /
• pp.352-356
• /
• 2009

The purpose of this study was to introduce the toxicological study review to evaluate the safety of PDMS on the 69th JECFA meeting. Polydimethylsiloxane is a polymer and its ADI was established at 23rd JECFA meeting in 1979. The ADI was maintained although the specification was expanded at its 26th, 29 th, 37 th meetings. Recently, it was reported that PDMS with low molecular weight and viscosity has high absorption rate and different toxicity, so it was submitted at 69th meeting. Toxicological studies of PDMS were submitted from the sponsor and additional information is collected from a document searching. The toxicological studies were reviewed in accordance with the 'Guidelines for the preparation of toxicological working papers for the Joint FAO/WHO Expert Committee on Food Additives'. In the available acute, sub-chronic and chronic toxicity studies on PDMS, dose-related increases in incidence and severity of ocular lesions(corneal crystal, inflammation of the corneal epithelium etc.) were consistently observed after oral dosing. It seems to be a local irritant effect, but the mechanism by which the ocular lesions arose is unclear, although the lack of absorption of PDMS indicates that it is unlikely to be a direct systemic effect. Consequently, the relevance of the ocular lesions for food use of PDMS could not be determined. The ADI of PDMS was re-established from 0-1.5 mg/kg bw/day to 0-0.8 mg/kg bw/day by applying additional safety factor 2 based on its ocular toxicity. The result of 0-0.8 mg/kg bw/day is a temporary ADI until further data are provided to 2010.