• Journal of the Korean Society of Marine Environment & Safety
• /
• v.17 no.4
• /
• pp.419-427
• /
• 2011

The characteristics for hydrogen production and the thermochemical properties of high temperature steam electrolysis(HTSE) device have been numerically analyzed in a two-dimension, steady-state with using the COMSOL $Multiphysics^{(R)}$. The main parameters for the calculation are applied voltage, ASR(Area-specific Resistance), temperature and pressure of the inlet gas flow. The results showed that thermal-neutral voltage was 1.2454 V and rather than the cell temperature increases or decreases with increasing applied voltage by thermal-neutral voltage starting this voltage the temperature in high voltage tended to rise and temperature in the low voltage tended to fall. And with, increasing the values of ASR, temperature inside the cell and the hydrogen production rate were decreased.

• Journal of the Korean Vacuum Society
• /
• v.8 no.4B
• /
• pp.524-529
• /
• 1999

We deposited diamond phase carbon thin films on Si substrate by the electrolysis of methanol solution. A little amount of ammonia solution was added to increase the current density of the electrolyte. We analyzed films by XRD and SEM. The chemical change of electrolyte during the electrolysis process was characterized by FTIR. We obtained better quality diamond phase carbon films at a lower applying boltage(300V) and temperature ($40^{\circ}C$) by adding ammonia solution to methanol electrolyte. Diamond (111), (220), (311) peaks were shown distinctively in XRD graph. Addition of ammonia solution resulted in lowering the applying bias voltage to 300V and the substrate temperature to $40^{\circ}C$ still maintaining a high current density at 80mA/$\textrm{cm}^2$, which prohibited a great loss of solution from vaporization. Possible change of chemical reaction due to the addition of ammonia solution was also discussed.

• Transactions of the Korean hydrogen and new energy society
• /
• v.13 no.2
• /
• pp.127-134
• /
• 2002

A Study on the application of ultrasonic with high frequency is carried out as a plan to rise the efficiency of the hydrogen fuel production in an electrolysis of water. KOH is selected as an electrolyte and concentrations are 0 %, 10 %, 20 %, and 30%. The solvent is city water. A measurable device of buoyancy by an electronic balance and a measurable device of voltage with a sensor of pressure are planned newly as a measuring device to measure the quantity of hydrogen production. An ultrasonic transducer with high frequency of 2 MHz is selected to give them the ultrasonic forcing. In results, it is clarified that ultrasonic influences the decrease of overpotential in the electrolytic solution. And basic data according to the pole interval and the temperature are obtained.

• Membrane Journal
• /
• v.30 no.6
• /
• pp.433-442
• /
• 2020

In this study, in order to build a molecular dynamics simulation model of ionomer for water electrolysis, an ionomer model that reflects the characteristics of a water electrolysis system in which excess water molecules exist was compared to an ionomer built according to the conventional simulation method of the fuel cells membrane. The final ionomer MD models have a strong phase separation and water channel that is one of the important characteristics of the perfluorinated ionomer, and are stable and water-insoluble under excessive water and high temperature conditions. In the ionomer MD models built in this study, the excess water molecules decrease an ion conductivity due to the dilution of ions, but increase a hydrogen diffusivity. Therefore, it is necessary to design the molecular structure of ionomers for water electrolysis in experimental studies as well as molecular dynamics studies according to the characteristics of the water electrolysis system reported in this study.

• Transactions of the Korean hydrogen and new energy society
• /
• v.35 no.2
• /
• pp.140-145
• /
• 2024

High temperature co-electrolysis of H₂O-CO₂ mixtures using solid oxide cells has attracted attention as promising CO₂ utilization technology for production of syngas (H₂/CO), feedstock for E-fuel synthesis. For direct supply to E-fuel production such as hydrocarbon and methanol, the outlet gas ratio (H₂/CO/CO₂) of co-electrolysis should be controlled. In this work, current voltage characteristic test and product gas analysis were carried out under various reaction conditions which could attain proper syngas ratio.

• Resources Recycling
• /
• v.16 no.3 s.77
• /
• pp.3-11
• /
• 2007

Presently, most of gold is smelted from gold concentrates and anode slimes. Anode slimes are by-products of nonferrous smelters such as lead and copper. In addition, gold is recovered from waste dental and medical materials, waste gold coating solution, and waste printed circuit boards (waste PCBs). The smelting method of gold from gold concentrates and various wastes containing high concentration of gold is largely divided into chlorination, cyanidation, and amalgamation methods. For the anode slimes, electrolysis method is usually used, which largely consists of roasting, high temperature melting and electrolysis processes. Also, various wastes containing low concentration of gold are mainly treated by pyrometallursical processes. In the paper, current status on gold smelting technology is reviewed, and a novel process for gold smelting which is researched in the recent is briefly introduced.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.11
• /
• pp.26-32
• /
• 2014

In electrolysis smelting plants that using high DC current, the bus bar is most important facility for delivering the high current. The copper made bus bar is widely used for various advantages as good electrical and thermal conductivity, resonable malleability, ductility, and not rust easily. However, when high current in copper bus bar, temperature rises and maximum allowable current capacity is restricted by temperature of bus bar. In this paper, we investigated temperature variation of copper bus bar by putting cooling water channel imposed to bus bar construction. For the validity, various simulations were carried out.

• Journal of the Korean Ceramic Society
• /
• v.43 no.12 s.295
• /
• pp.764-767
• /
• 2006

Ni/YSZ $(Y_2O_3-stabilized\;ZrO_2)$ composite as an electrode component for High Temperature Electrolysis (HTE) was fabricated by mechanical alloying method using Ni and YSZ powders. Characterization of the synthesized composite was investigated with various analysis tools, including XRD, SEM and PSA, and a self-supporting planar unit cell prepared with the Ni/YSZ composite was prepared to study the electrochemical reactions for the production of hydrogen. The Ni/YSZ cermet is composed of crystalline Ni and YSZ, in a sub-micro scale, and has an even distribution without aggregated particles. In addition, under an electrochemical reaction, the unit cell showed an $H_2$ evolution rate from steam of 14 Nml/min and $600mA/cm^2$ of current density at the electrode.

• Nuclear Engineering and Technology
• /
• v.39 no.1
• /
• pp.1-8
• /
• 2007

Hydrogen and electricity are expected to dominate the world energy system in the long term. The world currently consumes about 50 million metric tons of hydrogen per year, with the bulk of it being consumed by the chemical and refining industries. The demand for hydrogen is expected to increase, especially if the U.S. and other countries shift their energy usage towards a hydrogen economy, with hydrogen consumed as an energy commodity by the transportation, residential and commercial sectors. However, there is strong motivation to not use fossil fuels in the future as a feedstock for hydrogen production, because the greenhouse gas carbon dioxide is a byproduct and fossil fuel prices are expected to increase significantly. An advanced reactor technology receiving considerable international interest for both electricity and hydrogen production, is the modular helium reactor (MHR), which is a passively safe concept that has evolved from earlier high-temperature gas-cooled reactor (HTGR) designs. For hydrogen production, this concept is referred to as the H2-MHR. Two different hydrogen production technologies are being investigated for the H2-MHR; an advanced sulfur-iodine (SI) thermochemical water splitting process and high-temperature electrolysis (HTE). This paper describes pre-conceptual design descriptions and economic evaluations of full-scale, nth-of-a-kind SI-Based and HTE-Based H2-MHR plants. Hydrogen production costs for both types of plants are estimated to be approximately $2 per kilogram.

• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.6
• /
• pp.533-539
• /
• 2010

Ni-YSZ supported button cells were prepared by spray-coating YSZ and screen-printing YSZ-LSM powder as an electrolyte and oxygen electrode on Ni-YSZ cermet disks. In order to identify the polarization loss mechanism in high temperature electrolysis current-voltage characteristics coupled with electrochemical impedance spectroscopy were investigated as a function of temperature, current load, and the humidity. The effects of the different current collectors of platinum and silver for oxygen electrodes were compared. With Ag current collector two polarization losses were distinguished. The high frequency component was attributed to the Ni-YSZ cermet which was less susceptible to temperature variation but increasing in loss with humidity. The lower frequency component was attributed to the LSM electrode. Platinum current collector led to a much lower polarization loss.