• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.69-72
• /
• 2002

The high temperature deformation behavior of SiCp/2124Al composite and 2124Al alloy was investigated by hot compression test in a temperature ranged $400~475^{\circ}C$ over a strain rate ranged $10^{-3}~1s^{-1}$. The billets of 2124Al alloy and SiCp/2124Al composite were fabricated by vacuum hot pressing process. The stress-strain curve during high temperature deformation exhibited a peak stress, and then the flow stress decreased gradually into a steady state stress with increasing the strain. It was found that the flow-softening behavior was attributed to the dynamic recovery, local dynamic recrystallization and dynamic precipitation during the deformation. The precipitation phases were identified as S' and S by TEM diffraction pattern. Base on the TEM inspection, the relationship between the Z-H parameter and subgrain size was found based on the experiment data. The dependence of flow stress on temperature and strain rate could be formulated well by a hyperbolic-sinusoidal relationship using the Zener-Hollomon parameter.

• 대한금속재료학회지
• /
• 제49권3호
• /
• pp.211-220
• /
• 2011

To improve the low ductility and high strain-rate sensitivity in Sn-Bi based solder alloys, the influences of the minor additions of alloying elements (Ag, Mn, In) were investigated. The strain-stress curves of various Sn-40Bi(-X) alloys, including a pre-suggested Sn-40Bi-0.1Cu composition were measured using a tensile testing machine. As a result, the elongation and ultimate tensile strength (UTS) values were compared. The small addition (0.5 wt.%) of Ag significantly enhanced the ductility and high strain-rate sensitivity of the alloys at strain rates of $10^{-4}$ to $10^{-2}\;s^{-1}$ mainly due to the increase and refinement of eutectic lamellar structures. The microstructure change increased the area of grain boundaries, thus ameliorating the grain boundary sliding mode. It was also found that Mn is an effective element in enhancing the ductility, especially at the strain rates of $10^{-3}$ to $10^{-2}\;s^{-1}$ The enhancement is likely attributed to the fine and homogeneous microstructure in the alloys containing Mn.

• 대한기계학회논문집B
• /
• 제29권3호
• /
• pp.390-401
• /
• 2005

In this study, extinction limit extension of unsteady $(CH_{4}+N_{2})$/air diffusion flames was investigated experimentally. A spatially locked flame in an opposing jet burner was perturbed by linear velocity variation, and time-dependent flame luminosity, transient maximum flame temperature and OH radical were measured over time with the high speed camera, Rayleigh scattering method and OH laser-induced fluorescence, respectively. Unsteady flames survive at strain rates that are much higher than the extinction limit of steady flames, and unsteady extinction limits extend as the slope of the strain rate increases or the initial strain rate decreases. We verified the validity of the equivalent strain rate concept by comparing the course of unsteady extinction process and steady extinction process, and it was found that the equivalent strain rate concept represents well the unsteady effect of a convective-diffusive zone. To investigate the reason of the unsteady extinction limit extension, we subtracted the time lag of the convective-diffusive zone by using the equivalent strain concept. Then the modified unsteady extinction limits become smaller than the original unsteady extinction limits, however, the modified unsteady extinction limits are still larger than the steady extinction limits. These results suggest that there exist the unsteady behavior of a diffusive-reactive zone near the extinction limit due to the chemical non-equilibrium states associated with unsteady flames.

• 열처리공학회지
• /
• 제32권1호
• /
• pp.1-11
• /
• 2019

In this study, microstructure evolution and crystallographic orientation are investigated under various deformation conditions in M1 magnesium alloy. M1 magnesium ingot was rolled at 673 K with the rolling reduction of 30%. The compression test specimens were machined out from rolled plate, and then the specimens were annealed at 823 K for 1h. Uniaxial compression tests were conducted at 723 K and under the strain rate ranging from $5.0{\times}10^{-4}s^{-1}$ to $5.0{\times}10^{-2}s^{-1}$ up to a true strain of -1.0. For observation of crystal orientation distribution, EBSD measurement was performed. Occurrence of the dynamic recrystallization and grain boundary migration were confirmed in all case of the specimens. The distribution of the grains is not uniformed in the experimental conditions.

• 열처리공학회지
• /
• 제33권4호
• /
• pp.180-184
• /
• 2020

The crystallographic texture plays an important role in both the plastic deformation and the macroscopic anisotropy of magnesium alloys. In previous study for AZ80 magnesium alloy, it was found that the main texture components of the textures vary with the deformation conditions at high temperatures. Also, the basal texture was formed at stress of more than 15-20 MPa and the non-basal texture was formed at stress of less than 15-20 MPa. Therefore, in this study, uniaxial compression deformation of AZ80 magnesium alloy was carried out at high temperature (stress of 15-20 MPa). The uniaxial compression deformation is performed at temperature of 723 K and strain rate 3.0 × 10^-3s^-1, with a strain range of between -0.4 and -1.3. Texture measurement was carried out on the compression planes by the Schulz reflection method using nickel filtered Cu Kα radiation. EBSD measurement was also conducted in order to observe spatial distribution of orientation. As a result of high temperature deformation, the main component of texture and its development vary depending on deformation condition of this study.

• 한국미생물·생명공학회지
• /
• 제22권1호
• /
• pp.7-12
• /
• 1994

One bacterial strain, that had made the largest inhibition zone at the antagonism assay and also that lost the inhibition activity by the protease treatment, was isolated from raw milk. That strain was identified as Streptococcus salivarius subsp. thermophilus. The specific growht rate of this strain was maximum at 45$\circ $C. However, at this temperature the strain produced no bacteriocin. The bacteriocin activity was quite stable even at high temperature. Moreover, the activity of the vacteriocin was sensitive to proteases. but not to $\alpha $-amylase, DNase I, or RNase.

• 한국연소학회지
• /
• 제19권2호
• /
• pp.8-14
• /
• 2014

Experiments were conducted to clarify role of the outermost edge flame on low-strain-rate flame extinction in buoyancy-suppressed non-premixed methane flames diluted with He and $N_2$. The use of He curtain flow produced a microgravity level of $10^{-2}-10^{-3}g$ in $N_2$- and He-diluted non-premixed counterflow flame experiments. The critical He and $N_2$ mole fractions at extinction with a global strain rate were examined at various burner diameters (10, 20, and 25 mm). The results showed that the extinction curves differed appreciably with burner diameter. Before the turning point along the extinction curve, low-strain-rate flames were extinguished via shrinkage of the outermost edge flame with and without self-excitation. High-strain-rate flames were extinguished via a flame hole while the outermost edge flame was stationary. These characteristics could be identified by the behavior of the outermost edge flame. The results also showed that the outermost edge flame was not influenced by radiative heat loss but by convective heat addition and conductive heat losses to the ambient He curtain flow. The numerical results were discussed in detail. The self-excitation before the extinction of a low-strain-rate flame was well described by a dependency of the Strouhal number on global strain rate and normalized nozzle exit velocity.

• 한국지반환경공학회 논문집
• /
• 제15권5호
• /
• pp.67-74
• /
• 2014

본 연구에서는 점토의 액성한계에 따른 압밀특성을 연구하기 위하여 일정한 압력으로 예압밀 된 재성형 점토를 이용하여 표준압밀시험과 일정변형률 압밀시험을 수행하였다. 압밀시료들은 카올리나이트에 중량대비 6 %, 9 %, 12 %, 15 %의 벤토나이트를 혼합하여 제작하였으며, 시료들의 액성한계시험을 수행한 결과 각각 77 %, 84 %, 88 %, 91 %의 값을 얻을 수 있었다. 또한 액성한계의 약 2배의 증류수를 첨가 후 충분히 교반하여 0.2 MPa의 일정한 압력조건하에 예압밀시켜 제작하였다. 최근 일반적으로 사용되고 있는 표준압밀시험과 ASTM, D4186-82에 따라 변형률 속도를 0.001 %/min, 0.004 %/min, 0.01 %/min을 적용하여 일정변형률 압밀시험을 수행하고 선행압밀하중을 0.2 MPa의 예압밀압력에 대해서 비교 분석하였다. 그 결과 액성한계가 낮을수록 빠른 변형률 속도에서 선행압밀하중이 예압밀압력과 유사하게 나타났으며, 액성한계가 높을수록 느린 변형률 속도에서 선행압밀하중이 예압밀압력과 유사하게 나타났다.

• Structural Monitoring and Maintenance
• /
• 제10권2호
• /
• pp.155-174
• /
• 2023

High performance concrete (HPC) has been extensively used in thin overlay for repair purpose due to its excellent strength and durability. This paper presents an experiment, where the sensor-instrumented HPC overlays have been followed by dynamic strain and moisture content monitoring for 1 year, under normal traffic. The vibrating wire and soil moisture sensors were embedded in overlay before construction. Four given HPC mixes (2 original mixes and their shrinkage-modified mixes) were used for overlays to contrast the strain and moisture results. A calibration method to accurately measure the moisture content for a given concrete mixture using soil moisture sensor was established. The monitoring results indicated that the modified mixes performed much better than the original mixes in shrinkage cracking control. Weather condition and concrete maturity at early age greatly affected the strain in concrete. The strain in HPC overlay was primarily in longitudinal direction, leading to transverse cracks. Additionally, the most moisture loss in concrete occurred at early age. Its rate was very dependent on weather. After one year, cracking survey was carried out by vision to verify the strain direction and no cracks observed in shrinkage modified mixes.

• 대한기계학회논문집A
• /
• 제40권6호
• /
• pp.573-579
• /
• 2016

충격하중을 받는 재료의 변형거동에 관한 연구는 공학 및 산업의 다양한 분야에서 관심 받고 있으며, 이들 기계/구조물 부재의 변형 및 파괴거동의 다수는 중간 변형률속도 영역에 해당하는 것으로 알려져 있다. 따라서 이러한 변형률속도역에서 동적변형거동을 고려하는 것이 설계의 필수조건이 되었다. 이들 영역은 준정적과 SHPB 시험장치를 이용하는 고 변형률속도의 중간 영역에 위치하고 있어서, 종래의 적당한 시험장치를 이용하여 중 변형률속도를 얻는 것이 용이하지 않았다. 따라서 중간 변형률속도역에서 재료의 변형 및 파괴거동에 관한 유용한 데이터의 보고는 제한적이다. 본 연구에서는 이러한 문제를 해결하기 위해, 구축한 낙추식 충격 인장시험 장치의 신뢰성을 확보하였고, 이를 사용하여 탄소강의 중 변형률속도역에서 동적거동을 평가하였다.