• 한국결정성장학회지
• /
• 제14권1호
• /
• pp.6-11
• /
• 2004

Bias 인가된 hot filament CVD 방법을 이용해 티타늄을 RF sputtering 법으로 고속도강에 피복하여 중간 층으로 한 후 다이아몬드 박막을 피복할 때 bias 전압의 영향과 계면 층의 특성을 조사하였다. 다이아몬드 증착 시 bias가 인가될 경우 필라멘트에서 전자 방출이 촉진되어 다이아몬드 핵생성과 성장을 촉진시켰으며 본 실험에서의 최적 증착 조건은 증착 압력 20 torr, bias 인가전압 200V, 기판온도 $700^{\circ}C$로 나타났다. 강에의 다이아몬드 박막 형성 시 중간 층으로서의 티타늄은 Fe 및 C에 대한 확산도가 높고 탄화물 형성 원소이므로 다이아몬드 핵생성 및 성장에 적합한 원소로 나타났다.

• Journal of Welding and Joining
• /
• 제15권2호
• /
• pp.54-63
• /
• 1997

For the purpose of establishing laser welding condition (laser power, welding speed and beam focus) and of evaluating tailored blanks for two kinds of thin steel sheets SPCC and SK5M using in the thin plate structure such as automobile, train, and so on, investigated their $CO^2$ laser weldability under various initial welding conditions. SPCC thin sheet showed good weldability under some welding conditions. But, high carbon steel sheet SK5M needed heat treatment after welding to obtain ductility of the welded joint. And next, tailored blank was tested through deep drawing to evaluate reliability of their obtained laser welding conditions. The forming depths by tailored blank were SPCC+SPCC=22-25mm and SK5M+SK5M=13-25mm.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.256-259
• /
• 2004

In the present study, AZ31B sheets has a bad formability in room temperature, but the formability is improved significantly as increasing the temperature because of rolled magnesium alloy sheet has a hexagonal closed packed structure (HCP) and a plastic anisotropy. In this paper, after tensile test in various temperatures, strain rate, show the tensile mechanical properties, yield and ultimate strength, K-value, work hardening exponent(n), strain rate sensitivity(m). As temperature increased, yield, ultimate strength and K-value, work hardening exponent(n) are decreased but strain rate sensitivity(m) is increased. As cross-head-speed increased, yield, ultimate strength and K-value, work hardening exponent(n) are increased. And according to the temperature, how change the plastic anisotropy factor R. In addition, we observed how temperatures and cross-head-speed effect on microstructure.

• 한국염색가공학회지
• /
• 제34권3호
• /
• pp.197-206
• /
• 2022

The purpose of this study was to confirm the optimal spinning conditions for PLA (Polylactic acid) as a fiber forming polymer. According to the melt spinning test results of PLA, the optimal spinning temperature was 258℃. However, it needs to note that relatively high pack pressure was required for spinning at 258℃. At an elevated temperature, 262℃, mono filament was broken easily due to hydrolysis of PLA at a higher temperature. In case of fiber strength, it was confirmed that the draw ratios of 2.7 to 3.3 were optimal for maximum strength of melt spun PLA. Above the draw ratio, 3.3, the strength of the PLA fibers was lowered. It was presumed that cleavage of the PLA polymer chain over maximum elongation. The heat setting temperature of GR (Godet roller) showed that the maximum strength of the PLA fibers was revealed around 100℃. The degree of crystallinity and the strength of the PLA fibers were decreased above 100℃. The optimal take-up speed (Spinning speed) was around 4,000m/min. Thermal analysis of PLA showed 170℃ and 57℃ as Tm (melting temperature) and Tg (glass transition temperature), respectively.

• International Journal of Computer Science & Network Security
• /
• 제23권10호
• /
• pp.1-10
• /
• 2023

This paper proposes a method to extend Inter-Carrier Interference (ICI) canceling Orthogonal Frequency Division Multiplexing (OFDM) receivers for 5G mobile systems to spatial multiplexing 2×2 MIMO (Multiple Input Multiple Output) systems to support high-speed ground transportation services by linear motor cars traveling at 500 km/h. In Japan, linear-motor high-speed ground transportation service is scheduled to begin in 2027. To expand the coverage area of base stations, 5G mobile systems in high-speed moving trains will have multiple base station antennas transmitting the same downlink (DL) signal, forming an expanded cell size along the train rails. 5G terminals in a fast-moving train can cause the forward and backward antenna signals to be Doppler-shifted in opposite directions, so the receiver in the train may have trouble estimating the exact channel transfer function (CTF) for demodulation. A receiver in such high-speed train sees the transmission channel which is composed of multiple Doppler-shifted propagation paths. Then, a loss of sub-carrier orthogonality due to Doppler-spread channels causes ICI. The ICI Canceller is realized by the following three steps. First, using the Demodulation Reference Symbol (DMRS) pilot signals, it analyzes three parameters such as attenuation, relative delay, and Doppler-shift of each multi-path component. Secondly, based on the sets of three parameters, Channel Transfer Function (CTF) of sender sub-carrier number n to receiver sub-carrier number l is generated. In case of n≠l, the CTF corresponds to ICI factor. Thirdly, since ICI factor is obtained, by applying ICI reverse operation by Multi-Tap Equalizer, ICI canceling can be realized. ICI canceling performance has been simulated assuming severe channel condition such as 500 km/h, 8 path reverse Doppler Shift for QPSK, 16QAM, 64QAM and 256QAM modulations. In particular, 2×2MIMO QPSK and 16QAM modulation schemes, BER (Bit Error Rate) improvement was observed when the number of taps in the multi-tap equalizer was set to 31 or more taps, at a moving speed of 500 km/h and in an 8-pass reverse doppler shift environment.

• 한국레이저가공학회지
• /
• 제17권2호
• /
• pp.11-18
• /
• 2014

This research was conducted as a fundamental study to apply tailored blank welding technique into automotive production process. Specially we tried to apply the TWB technique to exhaust system. The materials used in this work were ferritic 439 stainless steel sheet with a thickness of 1.2mm and 0.8mm. Welding tests were conducted for BOP test and dissimilar thickness (0.8 to 1.2t) cases. Major process parameters were position of focus, travel speed, shielding gas and joint (gap) condition. As a result, there are nothing significant welding characteristic compare with TWB of carbon steel. Stainless steel shows the good weldability and mechanical properties (tensile, hardness and forming strength) also shows high level. Just problem is gap condition. However, also in this case, it shows not only good forming strength but also base metal fracture after tensile test. And to conclude, it is good opportunity to make lightweight design muffler using TB welding technique.

• 제어로봇시스템학회논문지
• /
• 제6권3호
• /
• pp.329-337
• /
• 2000

This study describes a pressure tracking control of hydroforming process which is used for precision forming of sheet metals. The hydroforming operation is performed in the high-pressure chamber strictly controlled by pressure control valve and by the upward motion of a punch moving at a constant speed, The pressure tracking control is very difficult to design and often does not guarantee satisfactory performances be-cause of the punch motion and the nonlinearities and uncertainties of the hydraulic components. To account for these nonlinearities and uncertainties of the process and iterative learning controller is proposed using Cerebellar Model Arithmetic Computer (CMAC). The experimental results show that the proposed learning control is superior to any fixed gain controller in the sense that it enables the system to do the same work more effectively as the number of operation increases. In addition reardless of the uncertainties and nonlinearities of the form-ing process dynamics it can be effectively applied with little a priori knowledge abuot the process.

• Transactions on Electrical and Electronic Materials
• /
• 제5권2호
• /
• pp.55-60
• /
• 2004

High-temperature Superconductor(HTS) tubes were fabricated in terms of different chemical compositions and various SrSO$_4$additions by centrifugal forming method. For powder melting by induction the optimum range of melting temperatures and preheating temperature were 1050$^{\circ}C$, 1100$^{\circ}C$ and 550$^{\circ}C$ for 30 min, respectively. The mould rotating speed was 1000 rpm. A tube was annealed at 840$^{\circ}C$ for 72 hours in oxygen atmosphere. The plates like grains more than 20 $\mu\textrm{m}$ were well developed along the rotating direction of mould regardless of initial chemical compositions and the amounts of SrSO$_4$in Bi2212. The specimen with Bi2212 composition exhibited T$\_$c/ of 83 K, while the specimens fabricated with other compositions are lower than 60 K. The measured I$\_$c/ and J$\_$c/ at 77 K(B = 0 T) in Bi2212 with 7 % SrSO$_4$ composition were about 680 A and 380 A/$\textrm{cm}^2$.

• 한국전산구조공학회논문집
• /
• 제29권2호
• /
• pp.105-114
• /
• 2016

구조물에 충격하중이 작용하면, 그 구조물은 통상적으로 대변형을 동반하는 소성변형과 최종적으로 그에 따른 파단을 경험하게 된다. 본 연구에서는 사고적 극한 상태에 대한 합리적인 설계를 위해 열성형된 판과 냉간성형된 판의 재료상수를 고속인장시험에 대한 수치시현을 통해 정의하였다. 변형율이 중간 속도 이하인 경우에는 변형율 속도의 영향을 무시할 수 있다는 가정과 함께 Cower-Symond 모델과 John-Cook 모델에 포함되는 재료상수들의 유용성을 참고문헌들의 결과와 비교하여 입증하였다. 본 논문은 향후 연구 내용에 대한 언급을 포함하면서 마무리하였다.

• 전기학회논문지
• /
• 제67권9호
• /
• pp.1239-1248
• /
• 2018

This paper proposes a fault tolerant and high efficiency operation algorithm for a 4 LEG DC/DC converter for a battery energy storage system(BESS) forming a main power source in a standalone DC micro grid. The BESS for the main power supply in the stand-alone DC micro-grid is required to operate at high speed according to fault tolerant control and load by operating at all times. Fault-tolerance control changes the short-circuit fault to an open-circuit fault by using a fuse in case of leg fault in 4 legs, and operates stably through phase shift control. In addition, considering the loss of the power semiconductor, the number of LEG operation is adjusted to operate at high efficiency in the full load region. In this paper, fault tolerant control and high efficiency operation algorithm of DC/DC converter for BESS in standalone DC micro grid is presented and it is proved through simulation and experiment.