• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• 제19권1호
• /
• pp.17-24
• /
• 1983

The authors carried out an experiment to find the optomotor response of killifish, Orizias latipes(TEMMINCK et SCHLEGEL) and Yellowtail, Seriola quinqueradiata (TEMMINCK et SCHLEGEL) according to the colors of the netting pattern on the visual screen and the revolving velocities of the visual screen. The experimental water tank was made of 0.5 cm thick transparent acryl in the cylindrical shape (100R$\times$42H cm). The water level in the tank was maintained 30cm high from the bottom. The colors of the netting pattern (mesh size: 19.1cm, width of netting twine: 1.5cm, hanging ratio: 84%) on the three visual screens were black, red and green respectively. The revolving velocities of the visual screen were controlled by pulley, bevel gear and variable speed motor in three steps; slow (15.0cm/sec), middle (37.4cm/sec) and high (62.9cm/sec). The fish was put into the water tank before each experiment and released in it for 30 minutes in order to acclimatize itself to the tank. The visual screen was revolved for 4 minutes per each experiment, at first the fish was released for 1 minute, and then the behavior of the fish was observed for 3 minutes. In the course of clockwise and counter clockwise experiments, 10 minutes-pause was given for the rest. The behavior of the fish was observed by video system, and rounding number and swimming speed of the fish were analysed. The results obtained are as follows: (1) Optomotor response rate of Killifish and yellowtail were 95% and 94% respectively. (2) Response of the fish according to the colors of the netting pattern on the three visual screens was best in black, and second in red and third in green. (3) Response of the fish according to the revolving velocities of the visual screen was best in high speed, and second in middle speed and third in slow speed.

• Journal of radiological science and technology
• /
• 제13권2호
• /
• pp.21-25
• /
• 1990

This report is study about difference of H-D curve in regular film and ortho type film, and obtained results as follows : 1. In the blue-color emission intensifying screen, ortho type films and in the green-color emission intensifying screens, regular type are decreased in their gradient. 2. When joint use of regular type film and ortho type film, the gradient difference not seen in blue color screen. 3. The gradient difference seen clearly in G4, KM screens(green color emission intensifying). Especially, in part of high film density, the gradient difference are great. So we have to right use of screen and film because not matched used of theare the sensitivity and gradient are decrease.

• Journal of Information Display
• /
• 제4권3호
• /
• pp.6-11
• /
• 2003

We have fabricated a carbon nanotube field emission display (CNT-FED) panel with a 2-inch diagonal size by using a screen printing method and vacuum in-line sealing technology. The sealing temperature of the panel was around 390$^{\circ}C$ and the vacuum level was obtained with 1.4x$10^{-5}$torr at the sealing. When the field emission properties of a fabricated and sealed CNT-FED panel were characterized and compared with those of the unsealed panel which was located in a test chamber of vacuum level similar with the sealed panel. As a result, the sealed panel showed similar I-V characteristics with unsealed one and uniform light emission with very high brightness at a current density of 243 ${\mu}A/cm^2$, obtained at the electric field of 10 V/${\mu}m$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제26권3호
• /
• pp.246-251
• /
• 2013

Screen printing is commonly used to form the front/back electrodes in silicon solar cell. But it has caused high resistance and low aspect ratio, resulting in decreased conversion efficiency in solar cell. Recently the plating method has been combined with screen-printed c-Si solar cell to reduce the resistance and improve the aspect ratio. In this paper, we investigated the effect of light induced silver plating with screen-printed c-Si solar cells and compared their electrical properties. All wafers were textured, doped, and coated with anti-reflection layer. The metallization process was carried out with screen-printing, followed by co-fired. Then we performed light induced Ag plating by changing the plating time in the range of 20 sec~5min with/without external light. For comparison, we measured the light I-V characteristics and electrode width by optical microscope. During plating, silver ions fill the porous structure established in rapid silver particle sintering during co-firing step, which results in resistance decrease and efficiency improvement. The plating rate was increased in presence of light lamp, resulting in widening the electrode with and reducing the short-circuit current by shadowing loss. With the optimized plating condition, the conversion efficiency of solar cells was increased by 0.4% due to decreased series resistance. Finally we obtained the short-circuit current of 8.66 A, open-circuit voltage of 0.632 V, fill factor of 78.2%, and efficiency of 17.8% on a silicon solar cell.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• 제16권1호
• /
• pp.70-76
• /
• 2004

High-temperature cylindrical sodium/stainless-steel heat pipes were manufactured and tested for transient as well as steady states. Total length of the heat pipe was 1 m and the diameter was 25.4 mm. Screen meshes of 3 different sizes were used to estimate the effect of mesh size on the thermal performance of the heat pipe. The minimum thermal resistance achieved was as low as 0.02$^{\circ}C$/W for the maximum thormal load of 2 ㎾. The average heat transfer coefficient in the evaporator was about 2,000 ㎾/$m^2$K and those in the condenser region were up to 5 times higher.

• Journal of radiological science and technology
• /
• 제11권2호
• /
• pp.21-26
• /
• 1988

Newly developed orthochromatic film HR series have many different types according to high speed, high resolution and special latitude. And now authors have practiced various screen-film combinations, those were usual regular type Fuji new RX film-LT screen and orthochromatic type HR films-rare earth G3, G4 screens. As a result of the experiment, we obtained high speed with high resolution and expansion of diagnostic range on the following combinations compared with usual new RX/LT series. Those combinations were RXO-G and HR-L films to skull, HR-G films to knee joint and hand part, HR-L film to abdomen. Therefore it may be desirable to select adquate kinds of HR series films according to investigated parts.

• Journal of Biosystems Engineering
• /
• 제30권4호
• /
• pp.195-201
• /
• 2005

The output of Stirling engine is influenced by the regenerator effectiveness. The regenerator effectiveness is influenced by heat transfer and flow friction loss of the regenerator matrix. In this paper, in order to provide a basic data for the design of regenerator matrix, characteristics of heat transfer and flow friction loss were investigated by a packed method of matrix in the oscillating flow as the same condition of operation in a Stirling engine. As matrices, several kinds of combined wire screen meshes were used. The results are summarized as follows; The packed meshes with high mesh no. in the side of heater part of regenerator showed effective than the packed meshes with low mesh no. in the side of cooler part of regenerator. The temperature difference and pressure drop of the regenerator were not made by the specific surface area of wire screen meshes but by the minimum free-flow area to the total frontal area. Among the No. 150 single screen meshes, 200-60 combined meshes, the 200-150-100 combined meshes showed the highest in effectiveness.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.125-125
• /
• 2011

In this study, we investigated the electrical, optical, structural, and surface properties of indium zinc oxide (IZO)/Ag/IZO multilayer electrode grown by specially designed roll-to-roll sputtering system using the flexible substrate. By the continuous roll-to-roll sputtering of the bottom IZO, Ag, and top IZO layers at room temperature, they were able to fabricate a high quality IZO/Ag/IZO multilayer electrode. At optimized conditions, the bottom IZO layer (40 nm) was deposited on a flexible substrate. After deposition of the Bottom IZO layer, Ag layer was deposited onto the bottom IZO film as a function of DC power (200~500 W). Subsequently, the top IZO layer was deposited onto the Ag layer at identical deposition conditions to the bottom IZO layer (40 nm). We investigated the characteristics of IZO/Ag/IZO multilayer electrode as a function of Ag thickness. It was found that the electrical and optical properties of IZO/Ag/IZO multilayer electrode was mainly affected thickness of the Ag layer at optimized condition. In case of IZO/Ag/IZO multilayer electrode with the Ag power (350W), it exhibited a low sheet resistance of 7.1 ohm/square and a high transparency of 86.4%. Furthermore, we fabricated the touch screen panel using the IZO/Ag/IZO multilayer electrode, which demonstrate the possibility of the IZO/Ag/IZO multilayer electrode grown by roll-to-roll sputtering system as a transparent conducting layer in the touch screen panel.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• 제47권4호
• /
• pp.66-75
• /
• 2015

Disposable diaper waste is consisted of plastic, fiber, and SAP (Super Absorbent Polymer). They are valuable to be used as raw materials of other products including plastic blocks and pulp mold. Nevertheless, disposable diaper waste have been disposed by landfill and incineration without recycling. Due to strict environmental regulations it is necessary to develop fractionation technique to recycle the disposable diaper waste. In this study the fractionation technique using pilot-scale stock preparation units was investigated. Process for separation of plastic and fibers from disposable diaper waste was composed by the combination of pilot-scale pulper, drum screen, screen and cleaner. Recovery rate of plastics and fiber was checked according to the various operating conditions. In drum screen, recovery rate of plastic was high when the cut size of disposable diaper waste was $5cm{\times}5cm$. The highest recovery rate of fiber was achieved with 0.3 mm slot screen. It is important to control the neutral state of SAP for improvement of recovery rate of fiber since SAP can be swelled easily in water. Therefore SAP can be controlled efficiently by the addition of calcium chloride into the pulper. Consequently recovery rates of plastics and fibers were over 90 and 80% under the optimum pilot operating conditions.

• Journal of the Microelectronics and Packaging Society
• /
• 제22권4호
• /
• pp.83-89
• /
• 2015

In this paper, we propose a fabrication technique for enhanced electrical properties of piezoelectric thick films with excellent patterning property using sol-infiltration and a direct-patterning process. To achieve the needs of high-density and direct-patterning at a low sintering temperature (< $850^{\circ}C$), a photosensitive lead zirconate titanate (PZT) solution was infiltrated into a screen-printed thick film. The direct-patterned PZT films were clearly formed on a locally screen-printed thick film, using a photomask and UV light. Because UV light is scattered in the screen-printed thick film of a porous powder-based structure, there are needs to optimize the photosensitive PZT sol infiltration process for obtaining the enhanced properties of PZT thick film. By optimizing the concentration of the photosensitive PZT sol, UV irradiation time, and solvent developing time, the hybrid films prepared with 0.35 M of PZT sol, 4 min of UV irradiation and 15 sec solvent developing time, showed a very dense with a large grain size at a low sintering temperature of $800^{\circ}C$. It also illustrated enhanced electrical properties (remnant polarization, $P_r$, and coercive field, $E_c$). The $P_r$ value was over four times higher than those of the screen-printed films. These films integrated on silicon wafer substrate could give a potential of applications in micro-sensors and -actuators.