• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2016년도 추계학술대회 논문집
• /
• pp.3-32
• /
• 2016

High power impulse magnetron sputtering (HiPIMS) technique has been developed for more than 15 years. It is characterized by its ultra-high peak current and peak power density to obtain unique thin film properties, such as high hardness, good adhesion and tribological performance. However, its low deposition rate makes it hard to be applied in industries. In this work, the development of HiPIMS system and integration of radio frequency (RF) or mid-frequency (MF) power supplies were introduced. Effects of duty cycle and repetition frequency on the microstructure, mechanical property, optical and electrical properties of some binary, ternary and quarternary nitride coatings and oxide thin films were discussed. It can be observed that the deposition rate was effectively increased by the superimposed HiPIMS with RF or MF power. High hardness, good adhesion and sufficient wear resistance can be obtained through a proper adjustment of processing parameters of HiPIMS power system.

• 동력기계공학회지
• /
• 제10권1호
• /
• pp.52-59
• /
• 2006

Graphite is well known as a material which has high-temperature thermostable property, chemical resistance against acid and alkaline state also is very easy to environment. Nowadays the need of graphite product is increasing rapidly because of its advantages. In this paper, the mechanical property of newly developed graphite products with high density is investigated with especially in compression test. I introduced the graphite specimens for this study by NGF method with two expandable graphite and compared to the specimens of commercial graphite sheet from expanded graphite which made by the rolling process. I investigated the characteristics of these materials by measuring specific weight, hardness, compressive strength and investigating structures by SEM, It is verified that the graphite products with NGF method has superior properties for using gasket materials than that of commercial graphite sheet.

• Journal of information and communication convergence engineering
• /
• 제7권2호
• /
• pp.219-222
• /
• 2009

An efficient interpolation FIR filter structure for high-density and low-power electronic devices is proposed. The proposed structure is based on polyphase decomposition property and look-up table method. By computer-aided design simulations, it is shown that the use of the proposed method can result in reduction in the number of gates by 54% and can reduce power consumption by 9%.

• 제어로봇시스템학회논문지
• /
• 제9권8호
• /
• pp.647-650
• /
• 2003

PLC (Power Line Communication) is the communication method using the existing power line installed in houses and offices to convert and transmit high frequency communication signal from tens of KHz to tens of MHz, and receive the filtered signal using high frequency filter The advantage of PLC is that PLC uses the existing power line installed in houses and offices so it does not require separate power line. Easy and convenient access using electric outlets is another advantage of PLC. However, PLC has some disadvantages such as limited transmission power, high load interference and noise, variable signal attenuation, characteristic of impedance, and selective possibility of frequency property. We designed the boiler temperature control system unit by using the PLC modem. We can avoid unnecessary heating of separate temperature control unit, and save the cost accordingly control stability of the proposed system is proven through the experiment.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 학술대회지
• /
• pp.499-502
• /
• 2004

A two-stage Class E power amplifier operated at 2.44GHz is designed in 0.25-$\mu$m CMOS process for Class-l Bluetooth application. The power amplifier employs c1ass-E topology to exploit its soft-switching property for high efficiency. A preamplifter with common-mode configuration is used to drive the output-stage of Class-E type. The amplifier delivers 20-dBm output power with 70$\%$ PAE (power -added-efficiency) at 2-V supply voltage.

• 동력기계공학회지
• /
• 제16권1호
• /
• pp.58-64
• /
• 2012

Power plant boiler is one of the most important utilities providing steam to turbine in thermal power plant. It is composed of thousands of boiler tubes for high efficient heat transfer. Boiler tube material is used in such high temperature and pressure as $540^{\circ}C$, $170kg/mm^2$. The boiler tube material is needed to resist corrosion damage, creep damage and fatigue damage. 2.25%Cr-1Mo steel is used for conventional boiler tubes. In these days steam temperature and pressure of the power plant became higher for high plant efficiency. So, the material property of boiler tube must be upgraded to meet the plant property. Several boiler tube material was developed to meet such condition. X20CrMoV12.1 steel is also developed in early 1980's and used for superheater and reheater tubes in supercritical boilers. The material has martensitic structure, which is difficult to evaluate the material degradation. Boiler tube material at severe condition was tested to evaluate long term and short term degradation and creep. Through long term and high temperature degradation test, lath structure was decreased and recrystallization has been proceeded by sub-crystal. And in this research the effect of temperature and stress on boiler tube characteristic,for example, deformation by creep was changed rapidly at relatively high temperature and stress because creep was affected easily by temperature and stress.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권5호
• /
• pp.349-353
• /
• 1999

In this paper, to fabricate the AC power electroluminescent device (PELD) with high brightness, new structure that constructed single emissive layer between electrodes was proposed. Dielectric and phosphor material structure that constructed single emissive layer between electrodes was proposed. Dielectric and phosphor material were BaTiO3 and ZnS:Cu respectively. Fabricated AC power EL devices were estimated by optical and electrical properties of EL spectrum, brightness, CIE coordinate system, transferred charge density and EL emission wave in time domain. With above results, we found that brightness of newly proposed AC powder EL power EL device was 2754 cd/m2 at 100V, 400 Hz and compared with conventional device structure.

• 한국지역사회생활과학회지
• /
• 제17권2호
• /
• pp.3-14
• /
• 2006

This study intends to offer suggestions for improving the security and competitive power of traditional liquors by investing in the status of intellectual property rights. Merchandising and the marketing strategies of traditional liquor are also addressed. The data was collected through a questionnaire survey given to 101 CEOs of traditional liquor manufacturers. The major results of this study were as follows: The management types of traditional liquor manufacturers were classified as the company 57 (56.4%), the corporation or the union 29 (28.7%), domestic industry 10 (9.9%), and marketing community or technology center 5 (5.0%). The competitive power degree of traditional liquor products was classified as strength 30 (31.6%), usual 30 (31.6%), weakness 35 (36.8%). The elements of strong competitive power were taste, functional (wellbeing) character, and attractiveness of the brand name. On the other side, reasons for weakness in competitive power were the marketing system, price competitiveness, and advertisement. The trademark registration of the traditional liquor appeared with 53%. The reasons not to pursue a trademark registration included the complicated and unnecessary process of registration acquisition, high registration expenses, etc. The perceptions of CEOs about the consumer's brand awareness for their product were low with an average 2.97. Explanations included insufficient advertisement and public relations, unrefined trademark design, and the meaninglessness of brand names. The marketing strategy of traditional liquor manufacturers according to annual sales were as follows: Manufacturers with high sales emphasized marketing strategies that focused on functional character, traditional image, high quality in image and package materials and design, high price strategies based on quality, and various sale promotions.

• 한국재료학회지
• /
• 제15권1호
• /
• pp.19-24
• /
• 2005

For the good combination of high-temperature strength, toughness and creep property, $9-12\%$ chromium steels are often used for gas turbine compressors, steam turbine rotors, blade and casing. In this study, the correlation of microstructural evolution and mechanical properties was investigated fur the specimens heat-treated at 600, 650 and $700^{\circ}C$ for 1000, 3000 and 5000 hrs. The microstructure of as-received specimen was tempered martensite with a high dislocation density, small sub-grains and fine secondary phase such as $M_23C_6$. Aging for long-time at high temperature caused the growth of martensite lath and the decrease of dislocation density resulting in the decrease in strength. However, the evolution of secondary phases had influence on hardness, yield strength and impact property. In the group A specimen aged at $600^{\circ}C\;and\;650^{\circ}C$, Laves phase was observed. The Laves phase caused the increase of the hardness and the decrease of the impact property. In addition, the abrupt growth of secondary phases caused decrease of the impact property in both A and B group specimens.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.283-286
• /
• 2005

Because CV Joint which is one of the component of automobile power train system communicates high power and performs power steering function, it requires high qualities such as high strength, high toughness and high fatigue resistance. This component undergoes a series of production processes such as forging, machining and heat treatment and required properties for this component depends on plastic deformation and heat treatment heavily. Therefore in this study, in order to these effects on mechanical properties due to plastic deformation and heat treatment we performed heat treatment following plastic deformation and then tensile test.