• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.961-964
• /
• 2003

This paper presents the temperature annealing effect on the dark current of the InGaAs waveguide photodiodes, which are developed for high-speed optical receivers. The interesting experimental phenomena were observed that the dark current is significantly decreased and the breakdown voltage is slightly increased after annealing at $250^{\circ}C$ whereas the dark current and the breakdown voltage are almost constant after annealing at $200^{\circ}C$. Based on the experimental results, the long-term annealing is more effective for the dark current improvement than the conventional curing process.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.41-46
• /
• 2003

Until now, the quantity to recycle wasted concrete as the great supplementary value was very little. But considering a insufficiency of the present state of aggregates, the recycling of wasted aggregates is indispensable. This study will offer the basic application data of the recycled aggregates to make by the new attempt and offer the basic data of the great supplementary value of recycled aggregate to make good use of precast process. The result of compressive strength, tensile strength, flexural strength and drying shrinkage test of concrete by recycled aggregates were similar to the property of normal aggregate concrete, and the contrary effect of recycled aggregate by high temperature steam curing do not have been found out. Therefore the great supplementary value of recycled aggregate to make good use of precast process is possible way to be helpful to a insufficiency of the present state of aggregates.

• 한국연소학회:학술대회논문집
• /
• 2006.04a
• /
• pp.13-18
• /
• 2006

Radiant burners are applicable to drying, preheating and curing in materials manufacturing processes. High radiation efficiency is one of the most important performance criteria for these burners. The wide variation in reported radiation efficiencies are partly due to the differences in the measurement techniques. In the present work, water cooled radiant heat flux meter was used to measure radiant heat flux from a metal fiber mat burner. Non-contact type thermometer was also utilized to measure the surface temperature of the burner. Combustion gas was measured by gas analyzers. According to the thermal loads and stoichiometric ratios, radiant heat transfer ratio and combustion performance were discussed here in.

• Journal of the Korean Wood Science and Technology
• /
• v.12 no.1
• /
• pp.38-43
• /
• 1984

Water soluble urea-melamine-phenol copolymer adhesive manufactured with 80 percent of urea resin contents was manufactured by different molar ratio for a high temperature curing type, and their properties and strengthes were examined through manufactures of plywood with Kapur (Dryobalanops spp.) veneers. The results are summarized as follows: 1. Specific gravities of air dried plywood manufactured from each adhesive ranged from 0.78 to 0.84 and their moisture contents met the KS requirement. 2. In dry and wet shear strength, $U_{80}M_{10}P_{10}$ copolymer resin showed the highest value and urea resin was the lowest, indicating that melamine and phenol were effective for increasing glue shear strength of urea resin. 3. In case of glue shear strength after boiling test, phenolic resin was the nest and melamine was not so effective as phenol on reinforcement of boiling water resistance of urea resin.

• Aerospace Engineering and Technology
• /
• v.1 no.2
• /
• pp.179-185
• /
• 2002

In this study, the structural design method for the modified long-endurance UAV is presented. Composite materials using room temperature curing method and wet lay up procedure is applied to all wing structures. The modified wing is composed of 3-piece component for improvement of ground handling. As the sandwich structure is efficient for light weight and high stiffness, all skin is used the sandwich consisting of glass/ epoxy fabric and balsa wood. The proof test is performed up to limit load corresponding to 4g load condition for the modified wing structure.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.11a
• /
• pp.48-49
• /
• 2013

This test investigates early strength and durability of concrete using early strength type materials(cement, Polycarboxylate acid). The goal of this test is to secure the strength of 5.0 MPa in 12 hours early age and strength of 14 MPa for 24 hours correspondingly. This type of admixtures, concrete curing temperature, amount of binder and other concrete properties were confirmed by experimental factors. Comparing outcomes from two cases on using early strength type materials and common materials resulted in reducing of costs and shortening of the construction period, that determined the economical benefits of using early strength materials in construction.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.1
• /
• pp.44-49
• /
• 2021

Recently, infrared (IR) and near-infrared (NIR) light-emitting diodes (LEDs) were widely used for home medical applications owing to its low output power and wide exposed area for curing. For deep penetration of the light under the skin, multiple LEDs with wavelengths of 700~10,000 nm were located on a flexible printed circuit board. When multiple wavelengths of LEDs were soldered on a circuit board, the lifetime of LED module highly depends on LEDs with a short lifetime. The mean time to failure (MTTF) was able to calculate with the experimental results under high temperature and the Arrhenius model. The results of this study could help companies to approve the warranty of LED modules and its product.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.11a
• /
• pp.125-126
• /
• 2023

This work explores the effectiveness of graphene nanoribbons (GNRs) in modifying the fire resistance of cement paste. The GNRs are added to the ordinary Portland cement at 0.10 wt% of the cement, and the sample is heated to target temperatures after curing for 28 days. Subsequently, the variations of compressive strength and pore structure are inquired by compared to the control sample without nano reinforcing and the sample with the same amount of carbon nanotubes (CNTs).

• Composites Research
• /
• v.37 no.4
• /
• pp.330-336
• /
• 2024

Silicon carbide (SiC) fibers exhibit excellent heat and chemical resistance at high temperatures. In this study, polycarbosilane melt spinning, oxidation curing, and pyrolysis were performed to fabricate amorphous SiC fibers, and their resistance heating characteristics were evaluated. A stick-type amorphous silicon carbide fiber heating element was manufactured, and the resistance was measured using the two-point probe method. The structural, electrical, and heating characteristics were evaluated at different pyrolysis temperatures. The fiber produced at 1300℃ displayed the highest conductivity and the maximum heating compared to the fibers produced at 1200℃ and 1400℃. This may be attributed to difference in the structures of the fibers, particularly the SiC and graphitic carbon structures.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.2
• /
• pp.160-167
• /
• 2017

The purpose of this study is to identify the possibility of developing the 100% Recycled-resources Absorbent-Pervious Alkali-activated Blocks using both the alkalli-binder and the recycled aggregate. In addition, It established a test method such as Void ratio, compressive strength, coefficient permeability, absorption, and evaporation. As a result, an alkali-activated using recycled aggregate block was able to manufacture an 24 MPa class absorbent-pervious blocks with a liquid type sodium silicate and early high temperature curing. In this case, water-holding capacity, absorption and relative absorption were more effective than the natural aggregates. In conclusion, Absorbent-pervious alkali-activated Block Using recycled aggregate has a surface temperature reducing effect of approximately 10 % compared to ordinary concrete block.