• Aerospace Engineering and Technology
• /
• v.9 no.2
• /
• pp.1-7
• /
• 2010

Fatigue properties of composite materials are extremely important to design durable and reliable helicopter rotor blades. However, it is very difficult to apply conventional fatigue test loads in short period. Therefore, accelerating test speed and facilitating spectrum load realization are required. In this study, we have developed a fatigue testing method that uses a resonance of simply supported beam type blade specimen. This test consists in exciting the blade specimen with a frequency that corresponds to its natural frequency. In that case, the test specimen similar to a beam fixed between two pivot points starts vibrating and is significantly deformed. Resonant fatigue tests were performed by changing exciting vertical amplitude and frequency, and S-N curves of each composite materials were successfully obtained.

• International Journal of Aeronautical and Space Sciences
• /
• v.10 no.2
• /
• pp.117-124
• /
• 2009

In the environment where various and complicated threat signals exist, RWR (Radar Warning Receiver), which can warn pilot of the existence of threats, has long been a necessary electronic warfare (EW) system to improve survivability of aircraft. The angle of arrival (AOA) information, the most reliable sorting parameter in the RWR, is measured by means of four-quadrant amplitude comparison direction finding (DF) technique. Each of four antennas (usually spiral antenna) of DF unit covers one of four quadrant zones, with 90 degrees apart with nearby antenna. According to the location of antenna installed in helicopter, RWR is subject to signal loss and interference by helicopter body and structures including tail bumper, rotor blade, and so on, causing a difficulty of detecting hostile emitters. In this paper, the performance degradation caused by signal interference by tail rotor blades has been estimated by measuring amplitude video signals into which RWR converts RF signals in case a part of antenna is screened by real tail rotor blade in anechoic chamber. The results show that corruption of pulse amplitude (PA) is main cause of DF error. We have proposed two algorithms for resolving the interference by tail rotor blades as below: First, expand the AOA group range for pulse grouping at the first signal analysis phase. Second, merge each of pulse trains with the other, that signal parameter except PRI and AOA is similar, after the first signal analysis phase. The presented method makes it possible to use RWR by reducing interference caused by blade screening in case antenna is screened by tail rotor blades.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.325-329
• /
• 2003

Nowadays many peoples are using helicopter in various fields, not only military use but also common people applications such as air-measurement, photography, transportation of goods and persons, saving life and fire fighting etc. And it will be expected more popular than now. Most important part of helicopter to increasing performance and to reducing noise is rotor hub-system. Hub system consists of rotor-blade and rotor-hub. We participate to develop next-generation rotor hub system with elastomeric bearing, part of rotor hub. In this paper we introduce about the role and shape of elastomeric bearing in next-generation helicopter hub system. Then we study about bearing-material requirements and measuring methods. Finally we represent some experimental results.

• Journal of Aerospace System Engineering
• /
• v.4 no.2
• /
• pp.21-25
• /
• 2010

Fatigue properties of composite materials are extremely important to design durable and reliable helicopter rotor blades. However, it is very difficult to apply conventional fatigue test loads in short period. Therefore, accelerating test speed and facilitating spectrum load realization are required. In this study, we have developed a fatigue testing method that uses a resonance of simply supported beam type blade specimen. This test consists in exciting the blade specimen with a frequency that corresponds to its natural frequency. In that case, the test specimen similar to a beam fixed between two pivot points starts vibrating and is significantly deformed. Resonant fatigue tests were performed by changing exciting vertical amplitude and frequency, and S-N curves of each composite materials were successfully obtained.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.343-349
• /
• 2011

A loosely coupling method is adopted to combine a computational fluid dynamics (CFD) solver and the comprehensive structural dynamics (CSD) code, CAMRAD II, in a systematic manner to correlate the airloads, vortex trajectories, blade motions, and structural loads of the HART I rotor in descending flight condition. A three-dimensional compressible Navier-Stokes solver, KFLOW, using chimera overlapped grids has been used to simulate unsteady flow phenomena over helicopter rotor blades. The number of grids used in the CFD computation is about 24 million for the isolated rotor and about 37.6 million for the rotor-fuselage configuration while keeping the background grid spacing identical as 10% blade chord length. The prediction of blade airloads is compared with the experimental data. The current method predicts reasonably well the BVI phenomena of blade airloads. The vortices generated from the fuselage have an influence on airloads in the 1st and 4th quadrants of rotor disk. It appeared that presence of the pylon cylinder resulted in complex turbulent flow field behind the hub center.

• Journal of Aerospace System Engineering
• /
• v.8 no.3
• /
• pp.41-46
• /
• 2014

Fatigue evaluations for the rotor blades of commercial or military rotorcraft have been carried out using the safe life concept since 1950s. Particularly, in the case of a rotor blade made of a composite material, a highly reliable fatigue life could be predicted by evaluation the cumulative damage using combination of fatigue life curve and load spectrum. However, there is a limit in adequately evaluating the strength reducing phenomena caused by damages or defects generated during the manufacturing process or impact damage induced by operational usages, using only the safe life concept. In this study, the fatigue evaluation process based on the damage tolerance concept is described and illustrated by means of successful application to substantiate the retirement time of composite rotor blades.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.541-542
• /
• 2009

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.2
• /
• pp.159-166
• /
• 2018

In this study, the internal structural design, dynamic characteristics and load analyses of the small scaled rotor blade required for LCH(Light Civil Helicopter) main rotor wind tunnel test were carried out. The test is performed to evaluate the aerodynamic performance and noise characteristics of the LCH main rotor system. Therefore, the Mach-scale technique was appled to design the small scaled blade to simulate the equivalent aerodynamic characteristics as the full scale rotor system. It is necessary to increase the rotor speed to maintain the same blade tip speed as the full scale blade. In addition, the blade weight, section stiffness, and natural frequency were scaled according to the Mach-type scaling factor(${\lambda}$). For the design of skin, spar, torsion box, which are the main components of the blade, carbon and glass fiber composite materials were adopted, and composite materials are prepreg types that can be supplied domestically. The KSec2D program was used to evaluate the section stiffness of the blade. Also, structural loads and dynamic characteristics of the Mach scale blade were investigated through the comprehensive rotorcraft analysis program CAMRADII.

• Aerospace Engineering and Technology
• /
• v.1 no.1
• /
• pp.1-7
• /
• 2002

This paper describes the analysis method about the dynamic characteristics and vibratory load through HDS(Helicopter Design Study). To analyze the dynamic characteristics of helicopter rotor blade, the natural frequencies and modes are calculated according to rotor operational speed(Ω). Generally the proximity of rotor natural frequency and N times of rotor operational speed is a dominant component to determine the helicopter vibration. Also we can predict the airframe vibration by calculating the airload of rotating blade exactly. We expect to establish the design procedure of rotor dynamics by describing the two major analysis methods necessary to rotor design.

• Journal of Aerospace System Engineering
• /
• v.1 no.1
• /
• pp.73-78
• /
• 2007

Self-noise from the rotor blade of the UH-1H Helicopter is obtained numerically by using the Brooks' empirical noise model. All of the five noise sources are compared with each other in frequency domain. From the calculated results the bluntness noise reveals dominant noise sources at small angel of attack, whereas the separation noise shows main noise term with gradually increasing angel of attack. From the results of two different tip Mach numbers with the change of angel of attack, the OASPLs at M = 0.8 show about 15dB larger than those at M = 0.4.