• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.1
• /
• pp.63-71
• /
• 2018

In this study, the torque and horizontal stress acting on vane were measured and then used to determine a friction angle of sand. A dry Nakdong River sand was prepared for loose and dense conditions in a cell and then pressurized with 25, 50, 75 or 100 kPa from the surface of sand. A vane (5cm in diameter and 10cm in height) was rotated and the torque and horizontal stress were measured at real time. A maximum torque was 3.5-9.5Nm for loose sand and 7.4-17.6Nm for dense sand, respectively. The maximum torque increased as an overburden pressure increased. The maximum torque obtained at 14-20 degrees of vane rotation, which was not influenced by the initial alignment of earth pressure and vane blade. An initial horizontal stress ratio was 0.33-0.35 on the average. The horizontal stress increased initially and then decreased due to particle disturbance. A friction angle was calculated from real time varying horizontal stress and torque, which decreased with increasing overburden pressure. The friction angle of loose sand from vane shear test was similar to that of direct shear test but that of dense sand was overestimated.

• Journal of Korea Multimedia Society
• /
• v.9 no.2
• /
• pp.234-243
• /
• 2006

The recent rapid development of HCI and surveillance technologies has brought great interests in application systems to process faces. Much of research efforts in these systems has been primarily focused on such areas as face recognition, facial expression analysis and facial feature extraction. However, not many approaches have been reported toward face direction detection. This paper proposes a method to detect the direction of a face using a facial feature called facial triangle, which is formed by two eyebrows and the lower lip. Specifically, based on the single monocular view of the face, the proposed method introduces very simple formulas to estimate the horizontal or vertical rotation angle of the face. The horizontal rotation angle can be calculated by using a ratio between the areas of left and right facial triangles, while the vertical angle can be obtained from a ratio between the base and height of facial triangle. Experimental results showed that our method makes it possible to obtain the horizontal angle within an error tolerance of ${\pm}1.68^{\circ}$, and that it performs better as the magnitude of the vertical rotation angle increases.

• Journal of the Korean Home Economics Association
• /
• v.30 no.3
• /
• pp.15-32
• /
• 1992

The purpose of this study was to detect the effect of the lower body type on the shape of flare skirts. The subjects for the wearing test were 50 female students, who were controlled in their hip and waist shapes. The skirts used for wearing test were six types(three flar angles $\times$ two fabric types). The effect of lower body type on the shape of flare skirts was determind by the hemline trace method and the silhouette photography. The data were then analyzed by the repeated measures of analysis of variance and the SNK multiple range test. The results obtained from this study were as follows : 1) When a flare skirt made with larger flare angle and better drapable fabric was worn, the numeric of the nodes increased as the drop value(hip - waist) increased. When a flare skirt made with smaller flare angle was worn, the width of horizontal sectio of hemline increased as the drop value increased. The hemline uneveness decreased on the sides and back as the drop value increased. When a flare skirt made with worse drapable fabric was worn, the sides angle of the flarskirt increased as the drop value increased. 2) When a flare skirt made with larger flare angle was worn, the numeric of nodes increased as the ratio of dropped hip increased. The wave-height increased and the back variation ratio of wave-height was higher than the front variation ratio of wave-height as the ratio of dropped hip increased. The hemiline uneveness decreased on the back as the ratio of dropped hip increased. When a flare skirt made with larger flare angle was worn, the sides angle of the flare skirt increased as the ratio of dropped hip increased.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.33 no.2
• /
• pp.109-113
• /
• 2007

Introduction. In patients with mandibular prognathism, Bilateral Sagittal Split Ramus Osteotomy(BSSRO) combined with orthodontic treatment reduces oral volume and influences tongue and other surrounding tissues. Purpose of this study was to analyze post-operative tongue position and airway dimension, as well as mandibular changes in vertical, horizontal, and angular dimensions. Materials and methods. Height of dorsum of tongue, width of airway, gonial angle and lower facial height of mandibular prognathic patients who visited Kangdong Sacred Heart Hospital from Jan. 2001 to Dec. 2006 were anaylzed via pre-operative and post-operative cephalograms. T-test was used to compare pre-operative and post-operative measurements. Also, correlations among pre-operative measurements of the patients were analyzed. Results and conclusion. A significant correlation was shown between ANS-Xi-PM area and location of dorsum of tongue in pre-operative patients. A significant superior movement of tongue and decrease of airway width was observed in post-operative patients. Also the upper gonial angle decreased significantly.

• Korean Journal of Applied Biomechanics
• /
• v.15 no.3
• /
• pp.175-183
• /
• 2005

This study investigates the kinetic characteristics of the Driggs motion in horse vaulting by stages through the three-dimensional video analysis of YTY and TABARA who won a high score and a low score respectively from the Driggs motion in horse vaulting during the Daegu Universiade 2003, which involves putting one's hands on the horse vaulting rotating sideways, stretching and rotating backward in the air, and twisting 900 degrees, so as to help develop the techniques of Korean gymnastic athletes. From the analyses of the duration of body center, horizontality, vertical position and horizontality, vertical speed and angle factors for each of four phases from the contact of the board to the takeoff from the horse vaulting. I arrived at the following conclusions: 1. It was found that the motion of bending oneself forward while rapidly stretching the knee joint when taking off from the board increases the horizontal speed of body center and shortens the time of the first jump. 2. It was found that S1 who won a high score shortened the time of the contact and takeoff from the horse vaulting and enlarged the shoulder joint angle for full blocking motion. It was also found that horizontal speed decreased while vertical speed increased when you rapidly stretch the right elbow joint while taking off from the horse vaulting. 3. It was found that horizontal distance was shortened to increase the height and time of staying in the air during the second jump.

• Korean Journal of Applied Biomechanics
• /
• v.15 no.3
• /
• pp.133-142
• /
• 2005

The purpose of this study was to compare of the kinematic variables from takeoff preparation to takeoff used by long jumpers who recorded over 8meters in 2002 Busan Asian Game and 2003 Daegu Universiade and 2001 national championship. The kinematic characteristics from the last three stride to takeoff at the takeoff board were analyzed such as velocities, heights and angles. The conclusion were as follows; In order to record over 8meters the national long jumpers should have under 5cm height variation at the penultimate stride of the run-up. In the approach phase the horizontal velocity of the jumpers should reach to 10m/s in touchdown at takeoff board The vertical velocity must have 3.75m/s simultaneously in order to record 8meters. The jumpers need to continue talent of the horizontal velocity in touchdown at takeoff board and require jumping power of the takeoff leg at takeoff board The appropriate body variation range ratio between takeoff and touchdown should be 1.2 vs 1 and the trunk angle at touch down on the board should be close to the erect posture for higher body flight.

• Korean Journal of Applied Biomechanics
• /
• v.26 no.3
• /
• pp.303-308
• /
• 2016

Objective: This study evaluated the vertical and horizontal forces in the frontal plane acting on a pedal due to the vertical alignment of the lower limbs. Method: Seven male subjects (age: $25.3{\pm} 0.8years$, height: $175.4{\pm}4.7cm$, weight: $74.7{\pm}14.2kg$, foot size: $262.9{\pm}7.6mm$) participated in two 2-minute cycle pedaling tests, with the same load and cadence (60 revolutions per minute) across all subjects. The subject's saddle height was determined by the height when the knee was at $25^{\circ}$ flexion when the pedal crank was at the 6 o'clock position (knee angle method). The horizontal force acting on the pedal, vertical force acting on the pedal in the frontal plane, ratio of the two forces, and knee range of motion in the frontal plane were calculated for four pedaling phases (phase 1: $330{\sim}30^{\circ}$, phase 2: $30{\sim}150^{\circ}$, phase 3: $150{\sim}210^{\circ}$, phase 4: $210{\sim}330^{\circ}$) and the complete pedaling cycle. Results: The range of motion of the knee in the frontal plane was decreased, and the ratio of vertical force to horizontal force and overall pedal force in the complete cycle were increased after vertical alignment. Conclusion: The ratio of vertical force to horizontal force in the frontal plane may be used as an injury prevention index of the lower limb.

• Korean Journal of Applied Biomechanics
• /
• v.15 no.4
• /
• pp.97-104
• /
• 2005

Previous studies of kinematic analysis of golf swing usually dealt with variations vertically. The purpose of the study was to examine the horizontal hip joints motion of the fifteen male professional golfers during driver swinging. Kinematic variables were calculated by the Kwon3D motion analysis program. Paired t-tests and one-way ANOVA were used to compare the hip height, distance, displacement, and position differences. Results showed that there were no hip height changes and no hip height differences between left and right hip from address to impact. The axis of the backswing was braced right hip, the axis of the downswing was moving left hip. Hips position at the top of the backswing showed that hips move to target prior to hands, which means the sequential motion of the chain linked body segments. From address to impact, left hip moving distance was longer than right hip(p<.001), but during the whole swing, right hip moving distance was longer than left hip(p<.001). Hip rotation angle to target line was $-48.14{\pm}9.32^{\circ}$ at top of the backswing, $40.88{\pm}8.44^{\circ}$ at impact, and $104.70{\pm}8.14^{\circ}$ at finish.

• The korean journal of orthodontics
• /
• v.24 no.4 s.47
• /
• pp.799-817
• /
• 1994

The purpose of this study was to evaluate the initial skeletal pattern and growth change of whom had responsed well to chincap therapy. 93 patients seleted for this study were in mixed dentition and treated with chincap for more than 2 years. And 54 subjects were selected from these total samples and classified into two groups by the improvement of four measurements : ANB difference, APDI, Wits appraisal, and AF-BF. One was good response group which consisted of 26 children and the other was poor response group with 19 patients. Various measures of the craniofacial structure in the initial lateral cephalograms and the annual increments were calculated and analyzed by comparing two groups with t-test. The results were as follows : 1. Good response group had more horizontal growth pattern in initial stage of treatment than poor response group, and the contributing factors of this result were anterior posterior facial height ratio, gonial angle, lower genial angle and SN-mandibular plane angle. 2. The maxilla was positioned more anteriorly in good response group. 3. The amounts of vertical growth of maxilla was smaller but the horizontal growth of maxilla was larger in good response group. 4. The mandible rotated more infero-posteriorly in good response group. 5. The good response group had more vertical growth pattern of mandibular condyle.

• Korean Journal of Applied Biomechanics
• /
• v.14 no.3
• /
• pp.135-147
• /
• 2004

This study was conducted to investigate the technical factors of Lu Yu Fu vault actually performed by three men gymnasts participated in artistic gymnastics competition of 2003 summer Universiade in Daegu through the DLT method of three dimensional cinematography. To analyze these vaults, the instant events of Lu Yu Fu were set in the board touchdown(BTD), the board takeoff(BTO), the horse touchdown(HTD), the horse takeoff(HTO), the peak height(PH), the mat touchdown(MTD) respectively and the phases of that vault were set in the board contact(BC), the preflight(PRF), the horse contact(HC), the postflight(POF), the grounding on mat(GM) respectively After calculating the performance times, the CG displacement velocity, the kinetic energy impulse reaction force moment arm torque at the horse, the released angle piked angle addressed angle, the angular momentum angular velocity of whole body in x axis, and the horizontal displacement between the feet and CG, the following conclusions were reached. To perform the better Lu Yu Fu vault, a gymnast must have the large horizontal velocity of whole body with fast run-up, decrease the duration time and the horizontal vertical displacement of whole body in PRF, have the enough time to judge the correct magnitude and direction of force to brake or push the horse so as to lengthen the HC duration time at any cost. Also it is desirable to increase the horizontal vertical displacement of whole body in POF if possible, maintain the adequate piked position to decrease the angular velocity of whole body in x axis, prepare the grounding on mat previously and delay the release of the hand from the body to keep the angular momentum.